Cisco VPN :: 2811 - How To Configure Easy VPN Server And Downloadable ACL
Jun 9, 2011
I'm am wanting to know how to configure Easy VPN server with downloadable ACLs on a cisco router 2811.
Indeed, I would like to set up a remote access vpn that uses radius for authentication of VPN clients. The radius server is connected to an Active Directory server that contains the log in / password. I would like to on the basis of the user who connects to the VPN, the ACL that define the services or servers to which this user can access is automatically applied on the router and define the rights of the users.
View 1 Replies
ADVERTISEMENT
Oct 28, 2012
I have a 2811 router and how to configure a RADIUS server using the CLI.
View 3 Replies
View Related
Jul 11, 2011
Is it possible to configure Easy VPN on brach side which has 877 series router and ADSL connection for internet such a way that for internet traffic it will use the local ADSL line and for the server in HQ it uses the tunnel.or for internet also it will go thrugth tunnel and uses internet link at the HQ?
View 3 Replies
View Related
Feb 3, 2011
I have a 857 (124-4.T12). And would like to setup an Easy VPN server. I can run through the wizard in CCP, but it does not work from the VPN client. It does not complete the first stage of comm. All I have done is run the wizard and create a user. I'm fairly happy with Cisco routers, but the VPN part is new to me. I've read the walk through document on the Cisco site. I created it on a new local loop back.
The first time I run the wizard and click test it tells me none of the cyrpto interfaces are up. Are there some prerequisite I'm missing?
View 6 Replies
View Related
Mar 30, 2011
We recently installed a 2911 sec router.On this device there are three Ipsec GRE Tunnnels which are working fine and an Easy VPN Server.The problem is that when clients connect to the easy vpn server they cannot ping anything inside , the configuration regarding protected networks is fine.After restarting the router the first client conneced works but when disconnected all the others are authenticating and the cant see anythining in the internal network . By checking the routing table i realized that the route to the virtual access interface is missing for no reason. i used the #debug ip routing detail command and i got the following during the client connection
Mar 31 09:51:37.875: RT: interface Virtual-Access5 removed from routing tableMar 31 09:51:37.875: RT: delete route to 192.168.20.9 via 79.xxx.xxx.xxx, Virtual-Access5
why is this route getting deleted?
View 2 Replies
View Related
Aug 27, 2012
Previously, I was able to configure our Easy VPN Server with local authentication.But now, I am trying to use LDAP authentication to match with our policies.
My router is a Cisco1941/K9.
Current configuration : 5128 bytes!! Last configuration change at 13:25:16 UTC Tue Aug 28 2012 by admin! NVRAM config last updated at 05:03:14 UTC Mon Aug 27 2012 by admin! NVRAM config last updated at 05:03:14 UTC Mon Aug 27 2012 by adminversion 15.2service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Router!boot-start-markerboot-end-marker!!!aaa new-model!!aaa group server ldap ASIA-LDAPserver server1.domain.net!aaa authentication login ciscocp_vpn_xauth_ml_1 localaaa authentication login ASIA-LDAP-AUTHE group ldap group ASIA-LDAPaaa authorization network VPN_Cisco localaaa authorization network ASIA-LDAP-AUTHO group ldap group ASIA-LDAP!!!!!aaa session-id common!!no ipv6 cef!!!!!ip domain name domain.netip cef!multilink bundle-name authenticated!crypto pki token default removal timeout 0!crypto pki trustpoint
[code]....
View 16 Replies
View Related
Nov 23, 2012
I used the Cisco Configuration Professional to add an Easy VPN Server to my 3825. I'm able to connect when remote but I can't ping the default gateway of 192.168.1.1 which is in the same network as the VPN DHCP pool. I can access every single other device on the VLAN segments but not the default gateway which means when i connect I can't look at my router. And there's more, I cannot ping anything offnet (ie 75.75.75.75).
Attached are some images which show some details from the client during the VPN connect and a few from the router (i had to use the lan switch as a jump host). If you can figure this out before I go back to the coffee shop to test this tomorrow I will send you a cake.
[code]...
View 6 Replies
View Related
Jun 19, 2011
I'd like to set up a downloadable ACL from my ACS 5.2 server to be applied for users authenticating for just one of my SSIDs / WLANs.
I intend to use this primarily for mobile devices to allow them to go to any of my physical locations, connect to the same WLAN regardless of location and then get the same downloaded ACLs (filtered based off of destination port and address) applied in each case.
View 3 Replies
View Related
Jan 13, 2011
I have a client machine that requiers a DSL connection
my office already has a leased line to the building so don't want to pay for a DSL and BT phone line.
Can i configure my 2811 to act as a DSL server so that I can plug the clients ADSL modem into my router and let it think that it has a valid DSL connection.
Then the 2811 can provide internet over my leased line.
View 2 Replies
View Related
Sep 19, 2011
I have cisco 2811 router and two ISP copper line. How can configure it as BGP router.
View 11 Replies
View Related
Mar 6, 2011
I have configured 1841 router as VPN server. All VPN users are getting authenticated using radius in ACS 4.1 I need to apply per-user downloadable ACL.
I have configured ACS for the Downlodabale ACL. Even ACS report acivity shows that ACL is applied to the authenticated user, but the traffic is not blocked or passed accordingly.
View 2 Replies
View Related
Apr 2, 2013
configured 2 EzVPN groups using a 2811 router, i am trying to do this but is not working i have another VPN working thru EzVPN but if i try to configure another group for another EzVPN client is not working and the problem is that the debug crypto isakmp say that Apr 3 08:45:25.802: ISAKMP:(1309): phase 2 SA policy not acceptable!
How is that possible? in my understand the EzVPN server will inject the the IKE (phase 1) and IPSec (Phase 2) parameters for the client and that's they dont need to negotiate nothing, is important to say that the EzVPN client is an ASA5505 with onlu DES encryption enabled, 3DES and AES are not available due to licensing reasons.
View 4 Replies
View Related
Sep 13, 2012
Facing a unique problem in my cisco Router (2811) .. Router is well configured but suddenly it stops working , when logged in using console the configuration register is observed to be 0x2142.
How does it automatically changes register value during operation?
View 4 Replies
View Related
May 7, 2012
I have been reading article url....wp1430161 and I am trying to get my head around the type of port authentication Methods & Modes I am going to require for a Proof of Concept using a Cisco ISE as the Authentication Server.
The switchport will have a single IP Phone in a Voice VLAN and then a Single host in a Data VLAN. Reading this article, I think I should be configuring "802.1x" authentication method using "Single Host" Mode.
However will that support a Downloadable ACL dependent on the user credentials? And will it allow a restricted ACL to be downloaded if authentication of the Machine or the User fails.? I dont really want to create & manage Guest & Remediation VLANs with thier respective ACLs on every switch in my enterprise, including our remote branch offices.
View 1 Replies
View Related
Mar 29, 2011
How do you configure port-security on a 2811 router? If not, is there a way to configure some type of security on each port ?
View 3 Replies
View Related
Feb 27, 2012
Currently 2811 series router is configured for site to site VPN, CAN I configure USER VPN on the same box. We want Users to connect to VPN Server using Cisco VPN Client. best authentication method for USER VPN
View 1 Replies
View Related
Jan 19, 2013
configuring policy based route for my cisco router?Basically, I have a 2811 cisco router with 2 ADSL ports. 1 port is for iiNet line and another port is for Telstra line.I want to configure a policy based route on the router so that:Any traffic coming from 1 internal IP (i.e. 172.16.x.1) will go through iinet line (i.e. Dialer 0) interface.Any traffic from rest of the office will go through the Telstra line (i.e. Dialer 1) interface. Is there any easy way to configure this policy based route?
View 8 Replies
View Related
Jan 3, 2012
I have a Cisco 6500 router at my POP site and I have a Cisco 2811 at the tail site. I have to bond 3 city to city T1s to make a 4.5Mg pipe between the 2 ends. How do I configure the routers to make this happen? This is a configuration example for a single T1:
POP end on 6500:
interface Serial1/0/1:0
ip address 10.125.1.1 255.255.255.248
Tail site on 2811:
interface Serial0/2/0
ip address 10.125.1.6 255.255.255.248
View 3 Replies
View Related
Nov 6, 2012
I tried to download the new firmware version (2.0.04) for Linksys x2000 hw version 1 Annex A: error 404 page not found.Same issue with 2 different machines on different internet connections.
View 3 Replies
View Related
Mar 16, 2010
I've been collecting information on principles of SHDSL connection. I have found plenty of examples on how to configure only one SHDSL link. Very soon I'm going to the site to install two independent SHDSL links in Cisco 2811 which has one Cisco HWIC-2SHDSL module, so I can route one type of traffic through one connection and another type of traffic through another. Both SHDLS links have static IP addresses and probably different VPI/VCI values. how to install two SHDSL links into one HWIC-2SHDSL module, set one value for VPI/VCI on one link and another value for VPI/VCI on another link, also set one IP address on one link and another IP adddress on another link?
View 13 Replies
View Related
May 24, 2012
I have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
View 4 Replies
View Related
Sep 30, 2012
I've setup a NTP service by using Cisco 2811 routers. This works fine at the moment, but in the end there are some questions left.
1. I'm using two 2811 Routers, one for primary, which is resceiving the time from PUBLIC NTP 1, and one for backup, which is resceiving the time from PUBLIC NTP 2. Is it possible to compare these to times an check if the match? And if not, generate an alarm via e.g. SNMP
2. Is it possible to check via SNMP, if the routers are reaching PUBLIC NTP 1 and PUBLIC NTP 2 for sync?
View 3 Replies
View Related
Apr 20, 2012
I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies
View Related
Nov 30, 2011
i trying to set up a terminal server, 2811 with an HWIC-16A und two octo cables. [code] connect and sometimes not. It seems the connection is established but i don't get a prompt von the target device.The target devices are cisco 2811 and cisco catalysts 3560.
View 1 Replies
View Related
Sep 18, 2011
Basically the problem that I have is that I have a new Exchange server sitting on 192.168.12.2 IP address and on the router I have this NAT enabled
ip nat inside source static tcp 192.168.12.2 110 212.115.5.5 110 extendable ip nat inside source static tcp 192.168.12.2 25 212.115.5.5 25 extendable
The Exchange can receieve emails but it will not send them. It cannot make connection to any of the smart hosts on port 25 or can't even send mail using DNS. When I run telnet my.smarthost.com 25 it will not connect but if I run that from the router then it connects fine.
View 1 Replies
View Related
Nov 22, 2011
I running site-to-site IPsec VPN in Cisco 2811 IOS 12.4 both site. Here I encounter a problem to access server on Site A from Site B
Site A having Leased Line connected to router with Public IP. I have done static mapping 1 web server to Public IP (NAT). This to allow external users to access the server via Public IP. At the same time, users at Site B would need to access to same server via Internal IP since they have Site-to-Site VPN established. But once I done Static Mapping (NAT), user at Site B unable to access the server at Site A using its internal IP. But external user can access server via Public IP. What went wrong here. Do i need to add extra command to get this done?
View 3 Replies
View Related
May 22, 2012
I'm trying to connect a Cisco 2811 using an octal cable to a Juniper MX480 console port.Since the distance between Cisco 2811 and router is 20ft, im using couplers and a straight-through cable for the lack of slack. This wiring doesnt work, however in another city it works going straight from the Cisco 2811 octal cable to the router since they are in the same rack.
View 4 Replies
View Related
Jan 25, 2013
I know the best thing one should do is install an ISA server and an Active Directory Domain Controller on separate servers. But for some reason, I want to configure my Windows Server 2003 as an ISA server as well as an Active Directory Domain Controller. What can happen to my server making it run improperly. For example, my ISA server will function mainly as a Firewall, I wonder if all the rules I create in ISA server determine what I mean it should work or I have to consider any affection from Active Directory DC to those rules?I have to ask this question because I've already installed both ISA and AD DC on my Windows Server 2003, already created an Allow. All rule (just for testing connection) in ISA server but I can't ping from all the clients to my server, all the clients can ping each other and the server itself can ping to all clients. I just think that may be the affection from AD DC to my AllowAll rule in ISA server.
I successfully created some rules that worked greatly as they should work but when I hadn't installed AD DC yet (just installed ISA), however right after installing AD DC, it still worked well (this made me think that AD DC didn't affect to how ISA works). Then I configured a little related to DNS server, and maybe something I don't remember exactly and now I can't ping from my client PC to my server. My network is virtualized using VMware 8 workstation and GNS3, at first there is no need of GNS3 because I just want to test my internal network (some clients connected to the internal interface of ISA server). Depending on VMware that I can't be sure if it is some fault of VMware or any other thing but my configuration on the servers.
View 5 Replies
View Related
Mar 24, 2011
We a remote user set up with a Cisco 877W that connects into a ASA5510 using EasyVPN (remote user has dynamic external IP)
The home setup also has a physical Cisco VOIP phone that connects into a Call Manager Express system over the VPN. The home user cannot hear the other end properly and voice is breaking up when using office apps on the VPN link at the same time (Outlook etc),
We continue to hear his voice OK when he is having these problems hearing us, so I guess the upload of voice from the 877 is fine and not struggling with congestion, so I have not put Qos Policies on the 877 as I guess it can only control what it is sending out and this is already working OK. Therefore its the 877 downloading from the ASA that seems to be the issue, voice is not getting prioritised when other traffic is getting sent down the same vpn link.
I have set up the following QoS policy on the ASA for this link so Voice traffic is prioritized, but the issue still occurs so I guess it doesn't work,
class-map HomeUser match dscp ef match tunnel-group ezvpngroup
policy-map VPNQOS class HomeUser priority
service-policy VPNQOS interface OUTSIDE
View 2 Replies
View Related
Jul 9, 2012
I have configured an easy vpn server in cisco 1905 ISR using ccp.The router was already configured with zone based firewall. But when i try to connect my office using vpn client i can reach only upto the internal interface of the router but can't access the LAN of my company.Do i need to change any configuration in ZBF since it is configured as 'deny any' from outside to inside ? If then what all protocols do i need to match ? Also is there any NAT exemption for the VPN clients?
For reference please see my full configuration:
Router#sh run
Building configuration...
Current configuration : 8150 bytes
!
! Last configuration change at 05:40:32 UTC Wed Jul 4 2012 by
[code].....
View 1 Replies
View Related
Sep 21, 2011
I have a new ASA5505 which I want to use for Remote Easy VPN. The device connects to the remote ends but I am not able to ping the remote network. The interface is new to me and I am not sure where to add the routes. The local network is 192.168.66.0/24. The remote network is 192.168.4.0/24
I am trying to connect the Remote (conf) to the Corporate (conf). I have done this many times but now the new ADSM interface is confusing. I added the commands as you indicated with no success. The ASA gave me an error when I had added nat (inside) 0 access-list nonat. I wouldn't allow me to enable the EasyVPN option while this command was on the configuration. Here are the cry isa and cry ipsec isa files as requested.
View 7 Replies
View Related
Feb 25, 2011
I want to know, is it possible to configure VPN server over LAN? VPN server will have access of internet through ISP's Router. We have already purchased STATIC IP. I have tried it with Windows server 2003 for VPN server and Windows Xp with Client servers. But i;m unable to establish the connection between VPN server & VPN Client. IS there any software to diagnose that where problem exist actually.
View 1 Replies
View Related
Oct 15, 2012
How to configure Radius server on router in packet tracer
View 1 Replies
View Related
