I have a client machine that requiers a DSL connection
my office already has a leased line to the building so don't want to pay for a DSL and BT phone line.
Can i configure my 2811 to act as a DSL server so that I can plug the clients ADSL modem into my router and let it think that it has a valid DSL connection.
Then the 2811 can provide internet over my leased line.
Ok ive finally got hold of something ive wanted to dabble around with for a long time now, my very own DSLAM! I have a Alcatel Lucent ISAM 7356, it has 48 ports for VDSL2 connections for POTS and xDSL lines, i know its backwards compatable with ADSL2+ aswell as VDSL2, Now heres where im struggling, i have no setup guide, no knowledge on how to configure the thing , it does have 1 lan port aswell as a 9 pin D sub console port and a fibre uplink port, i can power the unit on but i have no idea how to comunicate with the thing to configure it ( which will probley be another question when i get to that part) Just for your knowledge, ive been interested in setting one of these up to extend the reach of broadband from one house down the street where virgins network stops so i can bring high speed broadband right to the end of the street where i live.
View 4 Replies View RelatedI have cisco 2811 router and two ISP copper line. How can configure it as BGP router.
View 11 Replies View Relatedconfigured 2 EzVPN groups using a 2811 router, i am trying to do this but is not working i have another VPN working thru EzVPN but if i try to configure another group for another EzVPN client is not working and the problem is that the debug crypto isakmp say that Apr 3 08:45:25.802: ISAKMP:(1309): phase 2 SA policy not acceptable!
How is that possible? in my understand the EzVPN server will inject the the IKE (phase 1) and IPSec (Phase 2) parameters for the client and that's they dont need to negotiate nothing, is important to say that the EzVPN client is an ASA5505 with onlu DES encryption enabled, 3DES and AES are not available due to licensing reasons.
I have a 2811 router and how to configure a RADIUS server using the CLI.
View 3 Replies View RelatedFacing a unique problem in my cisco Router (2811) .. Router is well configured but suddenly it stops working , when logged in using console the configuration register is observed to be 0x2142.
How does it automatically changes register value during operation?
How do you configure port-security on a 2811 router? If not, is there a way to configure some type of security on each port ?
View 3 Replies View RelatedI'm am wanting to know how to configure Easy VPN server with downloadable ACLs on a cisco router 2811.
Indeed, I would like to set up a remote access vpn that uses radius for authentication of VPN clients. The radius server is connected to an Active Directory server that contains the log in / password. I would like to on the basis of the user who connects to the VPN, the ACL that define the services or servers to which this user can access is automatically applied on the router and define the rights of the users.
Currently 2811 series router is configured for site to site VPN, CAN I configure USER VPN on the same box. We want Users to connect to VPN Server using Cisco VPN Client. best authentication method for USER VPN
View 1 Replies View Relatedconfiguring policy based route for my cisco router?Basically, I have a 2811 cisco router with 2 ADSL ports. 1 port is for iiNet line and another port is for Telstra line.I want to configure a policy based route on the router so that:Any traffic coming from 1 internal IP (i.e. 172.16.x.1) will go through iinet line (i.e. Dialer 0) interface.Any traffic from rest of the office will go through the Telstra line (i.e. Dialer 1) interface. Is there any easy way to configure this policy based route?
View 8 Replies View RelatedI have a Cisco 6500 router at my POP site and I have a Cisco 2811 at the tail site. I have to bond 3 city to city T1s to make a 4.5Mg pipe between the 2 ends. How do I configure the routers to make this happen? This is a configuration example for a single T1:
POP end on 6500:
interface Serial1/0/1:0
ip address 10.125.1.1 255.255.255.248
Tail site on 2811:
interface Serial0/2/0
ip address 10.125.1.6 255.255.255.248
I've been collecting information on principles of SHDSL connection. I have found plenty of examples on how to configure only one SHDSL link. Very soon I'm going to the site to install two independent SHDSL links in Cisco 2811 which has one Cisco HWIC-2SHDSL module, so I can route one type of traffic through one connection and another type of traffic through another. Both SHDLS links have static IP addresses and probably different VPI/VCI values. how to install two SHDSL links into one HWIC-2SHDSL module, set one value for VPI/VCI on one link and another value for VPI/VCI on another link, also set one IP address on one link and another IP adddress on another link?
View 13 Replies View RelatedI have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies View RelatedMy setup is ISP-2811-PIX 515E-LAN. Right now, I am doing a PAT for IPSEC tunnels to terminate on the PIX. Do you recommend I use the 2811 instead of PIX for VPN or keep things the way it is? Trying to determine the best box to use.
View 4 Replies View RelatedI need to know which IOS should I download for my 2811 router to get all ip sla features
Router(config)# ip sla ?
<1-2147483> Entry Number
auto
enable
Note this is from my 2951 router.
I need full features like this in my 2811 router.so which IOS should I download.
I want to upgrade LMS 3.2 to 4.1. But when I look to "Special Notes and Exceptions for Devices Supported" document ,It seems that 2811 have 2 SysID.
Why there are two IDs for the same hardware and under which ID will my 2811 routers be classified into inventory database. This information is important since customer want to have support of 2811 in CiscoView of LMS 4.1 (around 200 devices).
Looking to implement CoPP in our 2811 ISR. We currently have the base 256mb of DRAM in there. Will this bring our router to its knees? I've priced a RAM upgrade.
View 0 Replies View Relatedi have a branch router that connects to mpls WAN. Also has a second interface that is used for dmvpn failover in case WAN goes down.We want to use this second interface also as the primary internet circuit for the branch. I changed the default route to the next hop address on the other side of the second interface and expected this to work.But i was told i need to set up NAT for this to work, and set up an ACL for NAT to use. how to set up NAT?
View 1 Replies View RelatedI have BGP router 2811. Want to configure BGP on it with two ISPs. How can i configure it?
View 1 Replies View RelatedI want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
I have a 2811 that I can remotely VPN to using Cisco VPN client however I cannot see the internal admin network (10.35.5.0).
Current configuration : 4845 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
[code].....
I have a particular site that is causing me trouble, this site is connected in a back to back configuration using 2811 at CO and 2621XM at CPE. The CO end is also the CO for 3 other sites so has a total of 4 wics installed (WIC-1SHDSL-v2), these other sites also have 2621XMs for the CPE.
The problem i am getting is when one site in particular transfers large files to/from client machines, the CPU on the 2811 jumps to 99%:
CPU utilization for five seconds: 99%/98%; one minute: 26%;
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
11 12881868 37249378 345 0.49% 0.50% 0.51% 0 ARP Input
54 8548592 30375358 281 0.40% 0.45% 0.41% 0 XDSL BACKGROUND
[Code]......
We have a cisco 2811 router with 2 ADSL interfaces. One dialer interface is used for internet and another dialer interface is used for VPN.
The dialer interface that is used for internet purpose is "Dialer 1" and the VPN is "Dialer 2".
The route looks like this: ip route 0.0.0.0 0.0.0.0 dialer 1
Basically, I am able to the ping the external IP address associated with the Dialer 1 interface, however, I cannot ping the external IP address associated with Dialer 2.
I have a Cisco 2811 with an additional HWIC-4ESW card. [code] I need to NAT anything heading out of the WAN port. [code] I can ping anything connected to my other private networks from my 10.0.24.0 network but nothing on the Internet. [code]
View 3 Replies View RelatedI just bought an additional router for my network and I'm in the process of setting it up.I have however hit a snag with enabling ssh on the device. It is a cisco router 2811 running IOS 15.0 (refer below to my attempts)
View 3 Replies View RelatedI want the below mentioned IOS image for backup purpose. But I am not finding it in cisco.com or anywhere in the in internet. where can I get this version of image other than my router.
c2800nm-advsecurityk9-mz.124-3d.bin
I have a 2811 ISR configured to provide the following services to my network: Internet access to LAN usersCisco Call Manager ExpressSite-to-stie VPN to 3rd party networksVPN server to provide VPN access to remote usersSecurity Zone configurationsStatic NAT configurations.Now I recently just got the ASA5510 device and I am not sure how to go about with the setup, whether to put the ASA in between the internet and the ISR (Internet - ASA - ISR - LAN), or put the ISR in between the internet and the ASA (Internet - ISR - ASA - LAN)? While i know I can move most of the config unto the ASA, i know that the CME cannot be moved, hence I would like to do the setup such that users on the network still have access to CME.
View 2 Replies View RelatedI've setup a NTP service by using Cisco 2811 routers. This works fine at the moment, but in the end there are some questions left.
1. I'm using two 2811 Routers, one for primary, which is resceiving the time from PUBLIC NTP 1, and one for backup, which is resceiving the time from PUBLIC NTP 2. Is it possible to compare these to times an check if the match? And if not, generate an alarm via e.g. SNMP
2. Is it possible to check via SNMP, if the routers are reaching PUBLIC NTP 1 and PUBLIC NTP 2 for sync?
I have a site that is connected to the internet via T1 into 2811 runing C2800NM-ADVENTERPRISEK9-M), Version 12.4(11)X. I have noticed that when i do a port scan on the outside nat pool i see well know ports in the closed state .ie...7,21,22,23,25,99,100,80,443. These pools for end users to access internet. Does this pose a security risk? What can i change to provide end user access to web but not let these well know ports open?
View 6 Replies View RelatedI have a Cisco 2811 router with two HWIC-ADSL cards configured for dsl connection. I have two lines from the same ISP and i am load balancing between them. I have created a couple of SLA's to check the state of the connections and add to the routing table the two default routes if both are up or any one of them is up.My problem is that when i try to download big files (especially antivirus updates) the download at some point stops (especially the antivirus exits with an error of unreachability). If i shut down one line everything works fine.Could i use something (configuration-wise) to prevent this problem from happening?????Is there any way i can combine the two lines? They are simple ADSL connctions with static ip's.
View 8 Replies View RelatedI want to create a VPN between two PC's, (the server "Data" and "Remote Desktop" check the topology below), the Router Clabeck (cisco 2811 ) is connected to the internet through int f0/0 using a PPPoE connection and connects all the LAN PC's by PAT to the internet (you can see all the configurations in the Show Run below), the "Remote Desktop" is any PC with internet connection.
F0/1 F0/0
DATA--------------------SW-------------------ROUTER(Cisco 2811)---------------------INTERNET---------------REMOTE DESKTOP
192.168.1.51 192.168.1.254 201.122.53.177 192.168.1.1
Current configuration : 2116 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[code]....
I try to implement the url filtering feature on a cisco 2811 router and whenever i enable the parameter map patterns the router retuns (after some time)
%Unable to compile obj regex.[code] The result is that the router blocks ALL webpages without giving a block page message.
