Cisco Switching/Routing :: Configure Bonding 3 T1s Between 6500 And 2811?
Jan 3, 2012
I have a Cisco 6500 router at my POP site and I have a Cisco 2811 at the tail site. I have to bond 3 city to city T1s to make a 4.5Mg pipe between the 2 ends. How do I configure the routers to make this happen? This is a configuration example for a single T1:
POP end on 6500:
interface Serial1/0/1:0
ip address 10.125.1.1 255.255.255.248
Tail site on 2811:
interface Serial0/2/0
ip address 10.125.1.6 255.255.255.248
View 3 Replies
ADVERTISEMENT
May 24, 2012
I have to configure router 2811 for Data and Voice network.However I have only one Fast Ethernet interface. [code]
what else do I need to configure on switchport on which Avaya phones are connected.And is there any extra command, i need to configure on the router and 2950 switch.
View 4 Replies
View Related
Dec 7, 2011
Is it possible to configure the switchports on a 6500 linecard before it has been inserted?
So for example, I have a 6509 with slot 9 free. I'm going to install a 48 port line card. Is it possible to configure those 48 ports before the card is inserted?
View 2 Replies
View Related
Jan 29, 2012
We have Nexus 7k running as my core with a 6500 manageing my server farm and IP services servers (call manager, IPTV ...)My edge switch are 4500s. We currently have RIP2 running between and the switchs and each 4500 is managing its own VLANs.The IPTV uses IGMP snooping and multicasting to broadcast the video feed. The problem that came up is that the we cannot configure a gatewar for the setup boxs for the IPTV system. They will only work on a single VLAN and they are spread all over the network.Can we configure only this VLAN to be propagated over our RIP network???
View 2 Replies
View Related
Feb 12, 2013
Setting up NTP. Currently the source for NTP within our network is our core 6500.Currently the NTP source for the 6500 are internet based NTP Servers. I would like to configure the 6500 to respond to NTP messages as the NTP Master. However will the 6500's source remain as the internet based NTP Servers?? In other words if the 6500is configured to be NTP Master, where would it get it's time from?
View 5 Replies
View Related
Jun 6, 2013
I have two switches (sanitized configs attached) and I am trying to bond int gi0/1 and gi0/2 between the two. Then I need int gi0/3 back to the main LAN switches. These are new Vlans created 982 and 983 for these switches. Question #1: do the configurations look correct? I haven't placed any laptops on the interfaces to test interconnectivity yet but I am wondering if it will work with no default routes.
The admin team needs these switches at location A for setup then they will be moved to Location B. The only thing that sucks for me is that the network admin before me created gateway interfaces for all the local Vlans on a main router as sub interfaces. For example, for these two subnets, I need to create subinterfaces below (at location A), which is why a gave the Vlan on the switches, ip addresses.
interface GigabitEthernet0/0.982
encapsulation dot1Q 982
ip address 10.98.2.1 255.255.255.0
ip flow ingress
no cdp enable
service-policy input mark-mplsqos-in
interface GigabitEthernet0/0.983
encapsulation dot1Q 983
ip address 10.98.3.1 255.255.255.0
ip flow ingress
no cdp enable
service-policy input mark-mplsqos-in
When I move the subnet to location B, I will also move the gateway. These two switches will be used mainly for a VMWare and HyperVisor environment so Vlan 982 is for VMA network and Vlan 983 is for management. The admin tells me the software needs to tag the packets, I am not sure if I care as the switches should handle that also.
View 1 Replies
View Related
Jun 9, 2013
I'm trying to configure a egress netflow in a 6500 (VSS) with VS-S720-10G supervisor. I foud some old posts and understood that netflow wasn't supported on 6500 but i found a new document and it seems that netflow is supported in Supervisor Engine 2T:[URL] Does the netflow still not supported in VS-S720-10G? It's weird because the command is supported:
#sh run int vlan 4
Building configuration...
Current configuration : 353 bytes
!
interface Vlan4
ip address X.X.X.X 255.255.0.0
[cod]....
View 1 Replies
View Related
May 15, 2013
we have currently a configuration with 3 bonded (link aggregation) channels, each delivering 1 Gb/s uplink, providing a total of 3 Gb/s uplink. Due to a recent network upgrade, we can now add more channels to the same group in order to have a total of 9 Gb/s uplink, meaning that we should bond toegether 9 channels. When we tried to change the old configuration in order to include six new channels to the bondend group we noticed 2 things: one channel was left in standby (blinking orange led),no increase in the uplink bandwidth semmed to happen,By looking around it looks like the channel group is limited to a maximum of 8 channels [*].
View 2 Replies
View Related
Feb 26, 2012
I have a switch layer 6500 series connected to a firewall, the port configuration between them is layer 2, in another words I do not configure an IP address in the Cisco switch port to conected it in the firewall, but when a apply a policy on firewall it lose communication with others vlans, just the vlan that is connected between the switch and firewall works, attachment the design. I think that is necessary to configure the connection between the firewall and switch as layer 3 ( a port with IP address in the switch), but I would like to know why? The switch is configured with about 10 vlan and it is a inter vlan routing, a default route is configured in the switch where the gateway is the firewall.
View 5 Replies
View Related
Dec 21, 2011
how can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies
View Related
Oct 23, 2011
I have four 2811 routers with IOS 12.4(15)T installed. Embedded Event Manager was introduced in IOS 12.3(4)T, why do I not have it?! I've been at this for over a month, when I try to see the command 'event manager' I get Unrecognized command? According to all EEM documentation I can find, this should work on our machines!
View 4 Replies
View Related
Jan 21, 2012
As per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 Replies
View Related
Sep 20, 2012
I am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
View 1 Replies
View Related
Jan 24, 2013
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies
View Related
May 9, 2013
I'm looking to restrict Inter-VLAN routing through L3 switch (cisco 6500) and wanted to know best possible way to do it. I used VACL and achieved success to some extent, but my config is making clients take up to 5-6 mins to authenticate IP address from the DNS (bootps).My VACL config was as follows:
Subnet to restrict is 10.100.15.0 (VLAN 15)
STEP 1: Created extended ACL to allow bootpc/bootps through DNS
ip access-list extended EACL_DNS
permit udp any eq bootps any
permit udp any eq bootpc any
STEP 2: Created standard ACLs to allow only relevant subnet, server VLANs & some IPs from other subnets for printers/scanners etc.
ip access-list standard SACL_VLAN_15
permit 10.100.15.0 0.0.0.255 (the subnet I'm restricting)
permit 10.100.50.0 0.0.0.255 (server VLANs)
permit 10.100.25.45 0.0.0.0 (printer in another VLAN which has to have access in VLAN 15)
STEP 3: Created VLAN access list
vlan access-map VACL_15 10
match ip address EACL_DNS
action forward
vlan access-map VACL_15 20
match ip address SACL_15
action forward
STEP 4: Applying VLAN Access list on VLAN 15 vlan filter VACL_15 vlan-list 15 Though the above works, below is noted:
1. I'm still able to PING 10.100.15.2 (the switch virtual interface) from outside the subnet, which I don't intend to do so. Howeve all cients in the subnet have no connectivity from outside the VLAN 15.
2. As mentioned its taking quiet some time to negotiate with the DNS server at system boot time.
View 3 Replies
View Related
Jan 4, 2012
i have 2811 router and i am coneccted via concole so i want to copy the 2811 ios to my PC is that possible?
how or give my the right decument to do this.
* idon't want to use TFTP becuse i have no ethernet connection to the router(only concole)
View 5 Replies
View Related
Oct 31, 2010
[URL]The Cisco 2811 does not support the HWIC-4T1/E1 module. But, I installed HWIC-4T1/E1 on the 2811 running 124-24.T2.
View 3 Replies
View Related
Dec 13, 2012
This is a 2811 rotuer running Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.4(24)T3, RELEASE SOFTWARE (fc2) Not sure why this isn't working. Can see it expects to parse the command. Can see this device is vtp server. Can see other vlans were defined here.
Router(config)#vlan ?
accounting VLAN accounting configuration
ifdescr VLAN subinterface ifDescr
Router(config)#vlan 35
^
% Invalid input detected at '^' marker.
[code]....
View 5 Replies
View Related
Jan 24, 2013
Just double-confirm that 2811 is compatible with HWIC-2FE based on your experience? Which IOS is compatible with HWIC-2FE? [URL]
View 3 Replies
View Related
Aug 10, 2011
I am facing a problem on a 2811 router. The CPU is remaining around 60% and the router throughput is reaching at most 18 MB while according to the data sheet the 2811 maximum throughput is 61MB. I have checked the output interpreter in order to try and figure out the cause of the high CPU and to determine if it is affecting throughput but there are not processes consuming more than 10%. I have attached the show tech-support and the show process cpu history outputs.
View 11 Replies
View Related
Jan 19, 2012
I currently have a 2811 and a LAN setup via a sub-interface FA0/1.3 and using a HWIC-AP I have a sub-interface dot11radio 0/1.5. I have them setup to work and surf the inet great, but I have recently been overly annoyed with the fact that the wifi cannot access windows shares on desktops and visa versa with the laptops.
The trick to make this happen is currently they are not on the same subnet. I know the answer is bridging the interfaces but when I do this using the simple commands:
bridge 1 protocol ieee
interface x & y
bridge-group 1
Although what should be simple has failed (good thing I tftp'd my working config). Here is my current configuration.
interface FastEthernet0/1.30
encapsulation dot1Q 30
ip address 192.168.3.1 255.255.255.0
[Code].....
View 3 Replies
View Related
Feb 17, 2007
Whether Cisco has part number for the large fan in 2811. I know p/n for small fan is already there, but I can't find any for large one( I think it s fan 3).
View 10 Replies
View Related
Sep 25, 2012
We have a site and on that site we have a server which is down form last two days. However , to manage these devices we are not using any tools. We are not able to find this server that where it is located and on which switch it is connected to.
I want to know that the timer for mac address is 5 minutes and arp timeout is 4 hours . Is there any way to find out the mac address of the server . I feel like this can we done with cef ? Is it true or not I am not sure. I am running 3750 stacks and 2811 routers. 3750 stacks are working as layer 3 devices. They are also running the pretty new IOS 12.2(53)SE.
According to my understanding now a days CEF entry does not expire if we are not using them. They remain in cache as we are running with destination base CEF.
View 4 Replies
View Related
Apr 25, 2012
I purchased several Cisco 2811 with Advanced IP Services - they are version 12.2.X
The product number looked like this
CISCO2811-HSEC/K9 2811 Bundle w/AIM-VPN/SSL-2,Adv IP Serv,10 SSL lic,128F/512D
I need to upgrade the IOS to version 15.1 - Do I require a license ? What happens if I install it without a License ? Am I entitled to a free license as I am not changing the software type (ADV IP Serv) ?
View 2 Replies
View Related
Jun 2, 2012
I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
View 3 Replies
View Related
Oct 30, 2011
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?
View 2 Replies
View Related
Sep 26, 2012
I have a remote site on a 2811 IOS 12.4(15). Interface FA 0/0 faces the ISP and is set for DHCP. What command can I run to see all of the information given out with the IP lease from the ISP? I need to find out what the IP address of the DNS servers are.
View 3 Replies
View Related
Feb 23, 2013
we have 2811 router with multiple servers connected to it's lan from which there are monitoring servers in between , the router suffers always from high cpu utilization
configuration has alot of ACLs & NAT & IPSEC Tunnel with wan bandwidth 20 M? Is there any method to reduce the high CPU utilization shown below !!
CPU utilization for five seconds: 90%/80%; one minute: 93%; five minutes: 90%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
104 737029848 427864243 1722 5.45% 5.65% 5.65% 0 IP Input
253 63392216 11081854 5720 1.04% 1.15% 1.12% 0 IP NAT Ager
260 82602372 137425723 601 0.64% 0.64% 0.66% 0 PDU DISPATCHER
[code]....
View 4 Replies
View Related
May 22, 2013
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
View 12 Replies
View Related
Mar 8, 2013
I have a Cisco 2811 router and i want to experiment on the IOS firewall.The thing is, none of the commands that are proposed in online guides - like ip inspect, ip audit, etc. - seem to be working. I just get "unrecognized command" on a router that is supposed to support such features. I'm wondering if it has something to do with the IOS image.
My show version output is this:
Cisco IOS Software, 2800 Software (C2800NM-SPSERVICESK9-M), Version 12.3(11)T9, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2005 by Cisco Systems, Inc.
Compiled Tue 13-Dec-05 08:24 by ccai
[code]....
View 5 Replies
View Related
Aug 31, 2012
I have a Cisco 2811 Router with a NM-16ESW card installed. I've connected this to my DSL connecting and I'm trying to build myself a learning lab. From the router I can ping to the internet and back to a test computer I have connected to one of the card's ethernet ports. From the test computer, I can ping the router's WAN interface, but no further. [code]
View 10 Replies
View Related
Dec 25, 2012
I want to configurate Vpdn protocol PPOE but i can not write protocol ppoe under vpdn group name on cisco 2811. cisco 2811 iso is 12.4 T adventurer and i upgrade it 15.1 advansecure but problem is still.
View 5 Replies
View Related
Dec 9, 2011
Will 2811 Router with 4 switch port module, How to do dual ISP configuration on this router.
View 10 Replies
View Related
