Does the Cisco 867w ISR router has an IOS with the Advanced IP Services? I need to use this router with Amazon VPC and BGP is required, where the Universal IOS does not accommodate BGP.
View 5 RepliesI have a Dell Desktop Studio running Windows Vista Home Premium 64-bit SP2.Since I got my PC new, almost 3 years ago, I have regularly gotten a Windows error "Advanced Networking Services stopped working." Windows never finds a solution when I click on that option. I've always ignored the message because I do no networking, but now I want to set up a wireless network so I can stream to my TV.
View 7 Replies View RelatedDoes the 3750G-12S-E support Advanced IP Services version of IOS?
View 3 Replies View RelatedI am trying to set up a VPN between my Cisco 867w device and the Amazon EC2 VPC solution. Amazon have stated that the Cisco ISR routers of IOS 12.4t and above should work, but when trying to input the config generated form the Amazon system into the router, the BGP config lines are not recognised. Does this router support BGP?
View 3 Replies View Relatedi have a 881G and an IP SLA icmp configured. (ip sla 1). I can get the status of it by the OID:
1.3.6.1.4.1.9.9.42.1.2.10.1.1.1
But, on the same router i have a track 1 for the SLA 1 and a track 2 monitoring track 1 with threshold . What i want, is to get the OID of track 2 so i can get the status of it. Which OID is that?
I am trying to set up a minecraft server but I am having trouble port forwarding. I port forwarded a linksysWRT160v3 router but still nobody could connect. So I read online that I might have to also port forward something sitting next to my router. (IDK what it is, i think its a modem or something) It is a Efficient Simon Speed Stream 5100. It says to type in 192.168.0.1 in my web browser for advanced setup but when I did it took me to a search engine.
View 3 Replies View RelatedWhat happened to "cable test" in 2.10 and 2.11? Thought this was I nice feature to check all connections. Also lots of settings in "advanced wireless are gone" (some are moved, many gone) Why?
View 1 Replies View Relatedin the QoS-section of the SRW2008P web-interface I can choose only between Disable and Basic, Advanced mode is greyed out.
I've created a new ACL but QoS Advanced mode isn't available.
What can I do to activate it?
Boot Version: 1.0.1
Software Version: 1.0.4
Hardware Version: 00.03.00
I'm having a issue when configuring Cisco ACS 5.2 appliance 1121 to integrate windows 2000 Active Directory as an External Users Database.I'm using an account with administrator privileges on AD (can create computer objects).The ACS register itself successfully to the domain but it doesn't retrieve the AD Groups, even when i change the seach base and filter.At this link says that ACS supports AD over Windows 2003, 2008 and 2008R2 but it doesnt say that not supports Windows 2000.[URL]
View 2 Replies View RelatedLMS 3.2.1, what is the correct baseline template syntax to accomplish the requirement 2:
Requirement 1
• Check if the router is running H323: You can do it looking for the command “h323-gateway voip interface”. If that command is found on a router then it is an H323 voice gateway
• Configure the global command: voice class h323 1
[Code]...
I got a ISE 3315 with an IP-Plus license on it. Now I need to install a Wireless advanced license, but I got an error when trying. I've read that the wireless license doesn't need the ip-base one but I can't remove it?
View 1 Replies View RelatedType of Wireless Adapter I have: Intel WiFi Link 1000 BGN When I click on (Properties) and then click the (Advanced) tab, there is a list of properties on the left and a list of values to choose from on the right. I'm curious on what each property does and, which property/value would be most "effective" or "appropriate" for a certain location/situation I'm in.
View 1 Replies View RelatedI have a SRP547W that I have configured the following way:
LAN 192.168.15.1/24 VLAN1
LAN 10.10.10.1/24 VLAN10
LAN 10.10.2.1/24 VLAN100
PPPOE ADSL
Software DMZ going to 10.10.10.x and another to 10.10.2.x - this is working OK
I now want to use the Advanced Firewall features to block all ports except those that I need as the software DMZ forwards everything. When I try to create the rules I get "the values are invalid" message no matter what I try.
I want to create explicit allow rules, followed by a deny all rule for each of the IP addresses used for the software DMZ
Have I got the Subnet Mask Correct for the Destination IP? Or should it be 255.255.255.0? It doesnt make a difference either way
Policy DetailsNameValueSource IP Address0.0.0.0Source Subnet Mask0.0.0.0Destination IP Address10.10.10.xDestination Subnet Mask255.255.255.254ProtocolAnySource PortAnyDestination Port443ActionPermitScheduleEverydayTimes24 Hours
I cant access the advanced user interface web page through the IP address 192.168.2.1. It's a belkin N router that worked for the first few days but now we can't access the Internet wirelessly if we shut the laptop down and reboot. Belkin talked me through every possible way to connect to AUI but no joy. Even tried using firefox, which worked once but we then lost connection again. Getting frustrated now. May take router back to the shop as it's only ten days old.
View 1 Replies View RelatedOur company is moving to a new location temporarily and we will be looking to do wireless for our network instead of wired. We have a dell power edge 2900 server running windows SBS 2008 and a switch with more than enough ports for what we need.What i need to know is how exactly to do the wireless and what hardware would work best for us. We plan to have approximately 45 computers hooked into the server and have some wired but for the most part wireless. Also we would want to look into advanced security options for our wireless set up as we will be in the same building as a few other companies.
View 5 Replies View RelatedA few months ago I purchased an e2500 Cisco Linksys router to use in my home. This past Christmas, my family got about 4 new wifi devices which they added to the network bringing the total number of devices on my home network to 10. I wanted to know if there are any advanced settings in Cisco Connect that I can tweak to make my wifi speeds faster because right now I'm getting about 55 Mbps on most of my devices. I was also wondering what the typical range of the e2500 router was and if the e4200 offers a large improvement.
View 3 Replies View RelatedManually type http://192.168.1.1/Wireless_Advanced.asp and the Advanced Wireless Settings tab appears! (I found this info in dd-wrt forum). A lot more settings to play with here, including transmission power for both 5GHz and 2.4GHz.
View 3 Replies View RelatedI've got a DIR-655 that I use as a wireless access point/switch (dhcp off) behind my Actiontec Verizon Fios router. The DIR-655 is in the basement and has my PS3 and Xbox hard wired to it.I've got playon server setup on my pc upstairs which is connected wireless to the Actiontec router. If I connect my ps3 wirelessly to the Actiontec, it immediately sees the playon server and streams movies without issue. However, when I hardwire the PS3 to the DIR-655, it will not pickup the playon server connected to the Actiontec router.I've got dhcp turned off and multicasting turned on under advanced settings of the Dlink.
View 5 Replies View RelatedI purchased an XPS-17 Laptop from Dell, which was delivered last week. This system includes the Intel Centrino Advanced-N 6200 wireless network card. I also purchased the Netgear Push2TV HDTV wireless adapter on the advice of the Dell customer representative. The representative assured me that the two functions were compatible, and that all I needed to do was to have the network card search for new networks. Unfortunately the network card does not "see" the Netgear module, only the wireless LAN operating in my home. The Netgear Push2TV is connected to the TV via HDMI, and the TV displays the Push2TV setup screen indicating that it is waiting for a connection from a network card.
I have spoken with Dell Tech Support with no success. First of all the Tech Support representative had no knowledge of the wireless TV display capability, let alone the Netgear Push2TV device, thus did not know how to diagnose the situation, neither did her supervisor. I authorized remote access into the computer and they tried all they knew how to do with no success. Finally, after 2 hours, I was told that Dell was aware of an incompatibility issue between the two devices, and that I should just wait until it was resolved by Dell and/or Netgear in "one or two days". After hanging up, I realized that I had not been given a Case Number, thus had no record of the call.I have been checking the Drivers/Downloads site daily, but find no new releases that are not already installed on the computer.
I can´t connect to wifi because it simply doesn't read my wireless network card, I can only connect by an ethernet cable. I've tried to see if it appears in the device manager but it doesn't..
View 7 Replies View RelatedI have just fitted a centrino 6200 half mini card in an attempt to improve wireless conectivity and more so range
I assume that it would come up as new hardware found and then run the driver to get it to work. When fitted it doesnt appear in device manager and when trying to run driver the driver just runs then stops
I want to know where I can edit advance settings of my EA6500. Cisco Clout Connect is too basic for my taste.
View 1 Replies View Relatedwhat is the optimal advanced settings for the ae2500 wireless adapter while gaming. I keep getting lag spikes with my games. Is there a always on option or like a gaming mode? If so what is it.
View 1 Replies View RelatedI Recently purchased the Linksys AE2500 adapter, upon looking at the advanced adapter settings, I couldn't find any more information pertaining to these settings on any linksys website or in fact online, where can I find a guide about these settings, Nothing about these setting was included on the CD.I set the basic one such as roaming aggressiveness but there are others that I would like to know about.
View 8 Replies View RelatedI just installed new E4200V2. After completing software install, everything appears to be working fine, except that I can't get to the advanced setup page, either through Cisco connect software or from the web page utility. Either way, the advanced settings web page never finishes loading. I am using the correct login information for the web page utility. It accepts the username "admin" and password, but never loads. Browser just sits there. Browser status bar says "waiting for http://192.168.1.1.
View 3 Replies View RelatedI recently bought a rtp300 and its on the 3.1.24 fw version I have been looking everywhere and i have not found any answer to my problem.It doesnt seem that you can change the pppoe settings (vpi,vci, encapsulation or PPP authentication ) anywhere. Should i return it If i apply the 5.01.04 i could those settings?
View 2 Replies View RelatedI have a new laptop, Inspiron 15R 5520, which comes with Intel Centrino Advanced-N 2230 network card. It can only detect my wireless-G netowrk at home, but not wireless-N. I have another computer that can connect to my wireless-N, so network is working fine. I have updated the driver to the greatess and latest.
View 2 Replies View RelatedI'm having some connection problems with my new laptop (Dell XPS 14z).When I'm close to my router (D-Link DIR 635), the connection works just fine.When I'm a bit further from my router, I get a poor connection and a slow speed. I've tested 2 other laptops at the same spot, both of which have no problem with the connection.
View 2 Replies View RelatedI have an XPS L502x laptop with an Intel Centrino Advanced-N 6230 wireless card with the latest driver 15.6.0.0. For the past couple of weeks the strength of the signal as measured by the Intel proset tools goes from excellent to poor in the space of 60 seconds, back and forth. It seems to do this on all channels from 1 to 13. It definitely is affecting Internet performance. I have the security set at WPA-Personal in an attempt to try and stabilise the network. I have also been using iSSIDer to try and find the best channel since there are about 10 other wireless networks from other houses around me. I have a D-Link 645 router which is admittedly about 10 metres and 2 or 3 walls away. However, until a fortnight ago, the network was dead stable showing a strong signal (4 or 5 bars (-50). Now it is all over the place. Could it be a damaged card?
View 5 Replies View RelatedI have a problem with my laptop , i had an old intel centrino advanced-n 6200 and this was not working anymore.I manged to buy a intel centrino advanced-n 6235 instead of 6200 as i could not find it.But when i installed it and installed the drivers the pc is telling me that "This device cannot start. (Code 10)"
View 5 Replies View RelatedRegion : UnitedKingdom
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : Sky
how to deselect the WMM option on the advanced wireless settings? The box is ticked and it won't allow me to deselect it?Model number TD-W8980
I've got a WPA wireless network set up that utilizes a total of 4 WRT54GL routers as access points (on channels 1, 6, and 11 [the two APs furthest from each other both utilize 11). Each AP generally supports about 5 clients at a time (though sometimes as high as 10).Generally, everything is working, but the clients furthest from the access points occasionally lose their connections, and some users have reported periods when they are completely unable to obtain an IP. I am virtually certain that this is based on poor signal strength resulting from distance from the APs and/or RF interference from other APs in the building. I have done everything possible to improve signal strength by router placement, optimizing channel usage based upon RF surveys, and upgrading to high-gain omnis.
This leaves nothing to do apart from tweaking the advanced wireless settings to marginally improve problems related to weak signal and/or RF interference, so I've been reading everything I can find on these boards and elsewhere about changing Fragmentation Threshold, RTS threshold, and beacon interval. However, I'm left with the following questions.
1) There seems to be disagreement about Fragmentation threshold and RTS threshold settings. Some (including the Linksys Technical Troubleshooting Wizard) recommend that both be set to 2304. I have also seen people insist that Fragmentation be set to 2306 and RTS to 2304. A few recommend 2306 for both thresholds, and some advise 2306 for Fragmentation and 2307 for RTS (though by my limited understanding, it simply disables RTS when the value is higher than the fragmentation threshold value). Which of these settings is best? And more importantly, WHY is it the best? Generally, I understand what the settings do, but I am reluctant to change them when there doesn't seem to be a consensus about exactly what they should be.
2) With respect to beacon interval, I've seen both 75ms and 50ms recommmended to replace the default of 100ms. For a network of my size (4 APs, averaging 5 users each), will increasing the number of beacons (and hence the RF traffic even when the network is idle) pose a problem? Also, I'm a little less clear as to how this would improve connectivity.
Since these settings will affect all users, I want to make sure that I'm using settings that will be beneficial on the whole. The last thing I want to do is inadvertantly make things worse, and since I can't test things directly from the standpoint of each user.
I am interested to know if there is anywhere (even in the code) where i can play with the guest network settings?
*. ability to change the default webpage login for guest network
*. Ability to set a lease time for guest network
*. Ability to use special characters in the password (@!$%)
is it even possible or an open source firmware is the way to go?