I have inserted a certificate check in the secure desktop prelogin policy. When using AnyConnect client version 2.5.2019, both Windows 7 and Windows XP computers fail to connect. The following pop up message is displayed...Posture Assessment Failed: prelogin failed.I have been successfully using IP address checks, file checks, OS checks, and registry checks during prelogin but cannot use a certificate check.
1. we upgraded our 5510 ASA firmware from 6.21 to 6.41
2. we also upgraded to the latest csd package (we have upgraded from 3.5.841 to 3.5.2008)
after 2 reloads, it seems that all my prelogin policies are gone ,i try enable / disable CSD and it just don't go back...i only have the default policy
There is ASA with remote access VPN and users are authenticated using third party signed certificates (CA is not local in ASA).When user certificate expires i can see it in syslog messages. For example:
%ASA-3-717009: Certificate validation failed. Certificate date is out-of-range, serial number: (...)
I would like to know if there is an opportunity to view user's certificate expiry date beforehand, say, 3 days before?
I have a Cisco ASA5520 that we are going to use to allow users to connect to our network via the Anyconnect client, I have authentication set up to validate against AD via LDAP, but was wondering if there were any way to set up the profile to check the PC before they log in....we do not want users using their home PCs to attach to our corporate network, only PCs that were issued to them by the company. Nothing is jumping out at me in the config, we are running some fairly old sofware on the boxes (ASA - v8.2(2), Anyconnect - v2.5.3046) I plan on upgrading the Anyconnect to v3.1 but will probably need to keep running the 8.2(2) version on the ASA due to support issues.
i know in Cisco PIX til 8.2 OS, if i have Nat control disabled and ACL permitting connection from Low Secirity ( DMZ ) to High Secuurity (INSIDE) then connectino should be successful, and i dont need any STATIC identity nat of inside IP to be created.
But i have Cisco PIX 525 with Version 7.2(2) Which is not allowing connection from DMZ to INSIDE , although nat control is disabled. and giving RFP check failure, any thought?
PIT525PIXINET# sh running-config nat-control no nat-cont
i have a router 1841 series and LMS send me amessage telling me the VPN AIM is not working on thsi device and i want to check the status of this VPN card
Error : compressed image check sum is incorrect 0xDC5C5348 Expected a check sum of 0x066C5349
I have uploaded a new firmware but same issue after booting, I have check the MD5 check sum in the image and Cisco and they are matching and verified, what could be the reason for all of this ?
How do I check IP address of others, when in chatting or playing online game, I could only know that he is Mr. X from YZA country which appears on Screen, But I also know he is using with wrong name and wrong Country name.I would to check his IP as well as his Place?
I want to check the transfer speed between my PC and another IP.The IP belongs to a DVR here is the general schematic of the sistem:Digital Video Recorder - Dynacolor - DynaGuard H.264 DVR (nDG80 - nDG600 - DG200) & DynaHawk Speed Dome & IP CamerFirst when I've worked with this system everything worked well but now after three weeks I have to open 5 ore more internet explorer windows to see live image and I can't see the recordings.I need to know the speed transfer because I want to know if someone had decreased my transfer speed between my PC and the router or DVR.
At one time a windstream (my internet provider) had talked me through a way to check the speed of my connections for my wireless network....I can' find the bookmark this was. How I can check this?
Yesterday, myself and local support team has been engaged to perform troubleshooting the issue of some web site accessing .Mos of this case is cased by MTU issue, So, I've tried to configure the following configuration on interface tunnel 0.Device: Cisco 7609 with IOS s72033-adventerprisek9_wan-mz.122-18.SXF8.bin
I've tried to figure out what the supporting command after 'ip tcp' in tunnel 0 and following likes..ip tcp ?compression-connections Maximum number of compressed connectionsheader-compression Enable TCP header compression.there is no such command about 'ip tcp adjust-mss.So, my questions is that what is the replace command for 'ip tcp adjust-mss' ? Is this only support on Router? such as Cisco 7200. or not, to take effect same functional on C7609, what is the command for that?
ASA running 8.2(5).When I enable ip spoofing on my network interfaces I see this getting logged:
Deny UDP reverse path check from 10.100.100.102 to 10.100.100.255 on interface SPECTRA-LAN
This is because interface SPECTRA-LAN (VLAN50) is the interface connected to the network with ip 10.100.100.0/24 but the interface do not have a ip address so it does not exist in the routing table I believe?However interface INTERN do also belong to network 10.100.100.0/24 which also is the management interface and the default route for hosts in network 10.100.100.0/24, but has no vlan.
1. move the management0/0 to SPECTRA-LAN and give SPECTRA-LAN ip 10.100.100.1?
2. give SPECTRA-LAN a ip address in the 10.100.100.0 range?
My routing table and interface list is:
Current available interface(s): DATA-BACKUP Name of interface Redundant1.10 DMZ Name of interface Redundant1.900 GUEST Name of interface Redundant1.990 HOSTING Name of interface Redundant1.100 Infrastruktur Name of interface Redundant1.20
I am working with ACS 5.2 and using Radius authentication for vpn client.
The authentication method used is Active Directory in an Windows enviroment with multiple domains in the same forest.
My problem occurs when i change a user from one group to another in Active Directory. After that i receive the following message when try to connect:
15039 Selected Authorization Profile is DenyAccess
The message is because match the default policy. Another user in the same AD group works fine. All domain in the forest have trust relation each other. I am using universal groups to include users from all domain belongs this forest.
how can i check the memory chips in the DIMM slots on a Cisco 2800 router ,my intention is I need to upgrade the IOS on the router for which I need to upgrade the DRAM and flash. Any CLI command available for the same ,as it is not very feasible to open the remote routers to check the DIMM configuration.
Does ASA 8.4.3 check the source IP address of a DNS reply and drop it if the reply address is different to that in the query?
Customers DNS server does this due to a recent change, their server now has a virtual address, but replies are sent from its physcial address. This is temporary. Their PIX is happy with this.
Replace the PIX with the ASA, DNS fails, the only reason I can see is due to the way their internal DNS operates.
How can you check if balance ACA is enabled in CSS11503? How can you see also if the content switch(CSS11503) is load balancing using balance ACA? "show load" command does not show it.
xxxxxx# show load Global load information: Reporting:Enabled Calculation method:Relative Step Size:Dynamic Configured:10 Actual:1280 Threshold:254 Ageout-Timer:60 Teardown-timer: Configured:20 Actual:20
Service load information: Average Average Peak Average Service Name Load Number ResponseTime Response Time ----------------------------------------------------------------------- DNS1 4 8999 33972 DNS2 4 8884 28254 SSH-WPHGT11 2 0 87509 WPHGT11 2 0 0 def-gwy-server 255 0 0 fe1-gw1-radius1 2 0 0 fe1-gw1-radius2 2 0 0 fe1-gw1-wap-8799 8 15344 662337 fe1-gw1-wap-9200 2 [Code].....
I have to make a live chat (web based using ASP.NET) , like a customer service chat when the client click to start chat , the server will repsond with checking any operators that is available to chat with the client.the operator must be login to the site as active operator .how can i make the server to check the available operator ? is there a syntax or codes that can be applied in this condition?
