I verified that the VPN implemented between a static IP address and a dynamic IP address every time the GPRS router IP address change address, the VPN does not rise.
I attach the configuration implemented by ASA5505 dynamic side.How can I fix it?
: Saved
: Written by enable_15 at 06:45:34.029 UTC Sat Dec 3 2011
!
ASA Version 8.2(1)
!
hostname ASA2
[code]...
I have a site with an ASA5505 and 2 isp connections but the catch is the 2 isp's are giving me a dynamic IP so I am unable to use this [URL]
View 3 Replies View RelatedI'm having problems configuring an IPSEC VPN between an SRP521 with a dynamic IP and a ASA5505 with a static IP. Static to Static is fine between these devices and I can configure that without problems. Dynamic to Static however.
View 1 Replies View RelatedI have a stack of 4 Cisco WS-C2960S-48FPS-L switches running c2960s-universalk9-mz.122-58.SE1 code. One of our network monitoring tools is indicating discards on a certain port on the switch. Upon further investigation I am seeing the Total output drops values change in a very odd manner.
The numbers seem to go from 573 to 1146 to 1719 then back down to 573 and it starts the same pattern over: [code]
The port utilization is quite low, the highest I've seen over the past 7 days is 3.5% with a polling period of every 30 seconds using Statseeker. Yet the discards are bouncing all over the place.
I've searched though the bugs for 12.2(58)SE1 and didn't see anything.
I have 2 computer connected and both have dynamic IPIf I change one of my computer's IP from dynamic to static Will it be okay to another comp ? ( Can it still connected to Internet / LAN )
View 1 Replies View Relatedi need to change from dynamic IP to Static for work, Iv rang my provider talk talk and the only way i can do this is go to a buisness line and pay more a month is there anyway i can log into my router and change from dynamic to static myself? im not on about the IP thats starts 192.blah blah blah its the one where u go somewhere like whatsmyip.com mine is dynamic as it changes if router is reset, there is hiccup in internet or computer is off for the night etc...
View 2 Replies View RelatedI Have a D-Link 364M, and a dynamic IP. But I've had this IP for over 2 years now and it does not changeCalled the ISP, they said it's a router issue and I need to contact D-LInk. D-Link says they do not cover my router anymore so I can't get support. Unplugging the router for 24 hours did nothing So I assume the problem is some internal setting on the router website that is doing this.
View 5 Replies View RelatedI need assistance regarding changing of DYNAMIC WAN IP to desired WAN IP to connect my e-mail server of my office, Problem is :i have a dynamic WAN IP at my home internet router , and my e-mail server at office only allows assigned WAN ips to connect , I want to connect from my home, i know the WAN ips which are allowed to connect my e-mail server and i want to change my dynamic wan ip virutally to desired WAN ip for incoming and outgoing traffic from my wireless router, What I need to do :I need to change my dynamic WAN IP to an static desired ip at my wireless router?
View 4 Replies View RelatedHow to change my dynamic ip address in windows 7
View 2 Replies View RelatedHow do I change my cisco wireless from a dynamic setting to a static settings.
View 1 Replies View RelatedI currently have an out of the box ASA5505 and need to change the internal interfact from 192.168.1.1 to 10.20.3.1 so it fits in with the rest of the network.Tried using the ASDM Startup wizard (via 192.168.1.1) and it just seems to hang on "delivering the commands to the device".
View 16 Replies View RelatedHow to remotely changing ip address for my ASA5505.
View 1 Replies View RelatedThe problem is that the PABX is sending out an internal address in it's INVITE messages and the ASA5505 isn't changing the internal address to the external address.We need> From: Calling Number <SIP: SIP Username@Public IP Address>However our PABX sends out> From: Calling Number <SIP: SIP Username@Private IP Address>. How to translate the internal IP address to the external IP address on an ASA 5505?
View 1 Replies View RelatedI am configuring Clientless SSL VPN on ASA5505 with 8.2(2)17. After the login, default page should be "Home", but if activating "Anyconnect". it always goes to Anyconnect as a first page. If disabling "Anyconnect" using SSL VPN Customization Editor --> Portal --> Application, it always goes to the other one. Never get "Home" as a first page, can I set the first page manually?
View 3 Replies View RelatedAs per CISCO QoS document URL, IOS from 12.2(13)T support drop command in policy map. But our CISCO ASR 1013 having IOS of Version 15.2(1)S1 doesn't have drop syntax.How can we drop specific application using QoS in ASR 1013 of IOS version 15.2 and higher?,Can I allow few users for a particular application (like P2P) and drop other users based on users source IP?
View 2 Replies View RelatedI having a basic query in troubleshooting E1 link , here im facing packet drop in the link and we are testing by providing local loop and remote loop from the CSU/DSU at local point and at remote point . I have tried ping test while the loop is given at local point and remote point ie i have pinged my local serial interface IP address (eg 10.0.0.1 -local & 10.0.0.2 -remote ) in Remote Loop i could see no errors and drops and also the traffic on the interface output and input is the same(eg input rate 1000bps and output rate 1000bps) .My query is that when i am pinging the local interface IP does the icmp packet travels till the loop point and comes to the same interface(like a boomerang) .
ICMP packet
->->->->->->->->->->->->->->->
R1 Local CSU/DSU | Remote CSU/DSU (remote loop given )
O-----------O------------------------------O |--------------------------------------O R2
<-<-<-<-<-<-<-<-<-<-<-<-<-<-<-|
We've had Cisco 1252 APs running on PoE (3750E gives the port 20W of power) for well over 3 years with no problems. These have not been touched, moved or configured since they went in.
All of sudden we're seeing these APs drop off the network and investigations reveal that they show as IEEE PD when you do a show power inline.
Some of these are slated to be replaced after the ports were changed, the cables replaced and port reset (also an old spare 1252 was inserted in to one of these ports and it came up fine, indicating an issue with these APs).
If it was one or two then maybe I could believe that the APs are at fault, but with so many (10 so far) I'm struggling to believe it. Could it be the code we are running on the switches? We are running 12.2(50)SE3.
my Cisco anyconnect VPN clients are able to access all of my internal networks accept to another site which has a IPSEC VPN site-to-site. The Cisco ASA forwards the packets destined to this remote site to a Cisco router which NATS the source addresses (pool 10.17.252.0/24) to a 192.168.46.0 range. The remote network is 155.x.x.x which I have included in my internal subnets object-group and added a route on the ASA to route it inside.
I have configured NAT so that it does not NAT anything from the anyconnect client range to the internal subnets. I am using version 8.3(2) and the NAT rule is:
nat (outside,inside) source static SSLPOOL SSLPOOL destination static INSIDE_NETS INSIDE_NETS
I can still not connect to the remote side via the VPN; when I run this throught packet-tracer, I get a failure on phase 6:
Type: WEBVPN-SVC
Subtype: in
Result: DROP
Result:Drop reason: (acl-drop) Flow is denied by configured rule
I cant seem to work out what it is that is blocking it. The NAT rule above is rule 1 in case some other NAT rule is causing the issue..
i see that the wifi on the SRP Freezes. If i am connected via lan, i can still surf the net or connect to another access point on the network and surf. But the wiress devides connected to the SRP loose connectivity even though it shows that the wifi connection is connected. I am running on the latest firmware. this problem has started occcuring only recently
View 3 Replies View RelatedIXIA----DUT-----IXIA
| | |
|_______ |________|
DUT has redudant connections to IXIA. Im pumping traffic from IXIA and traffic takes PATH A .. When I shut PATH A, i expect traffic to shift to PATH B within 100ms (example). How do I test this ?
I have a problem with configuring of my vwic3-2mft-t1/e1 card on Cisco 2821 router. I need drop some raw data timeslots from E1 frame and then insert them into frame on other port. I enter the following commands:
card type e1 0 0
controller e1 0/0/0
tdm-group 0 timeslots 1-4
clock source line
controller e1 0/0/1
tdm-group 2 timeslots 1-4
[code]....
I find these commands in Cisco 1 and 2-port T1/E1 Multiflex Voice/WAN Interface Cards for the Cisco 1700 Series Router configuration guide for vwic2 cards.But this config is not working properly. show connect output is showing status of connection "UP", show controller e1 shows no errors on both e1 ports, but data not flows between ports.What am I doing wrong? Have vwic3 and vwic2 cards different configuration procedures or not?
I have a working configuration with a 2811 router at my remote site in which I take the T1 (point-to-point PRI) into port 0/0/0 on the dual-port vwic2-mft-t1/e1 card. Then I plug my PBX into the 0/0/1 port. I channelize the T1 so 1/2 of the channels are used for data (13-24) and channels 1-8 are passed through the vwic2 to the PBX. I'm using the connect tdm t1 0/0/0 0 t1 0/0/1 0 command to pass the voice calls through to the PBX.
I tried to upgrade the router to a 2911 with the same card and the same configuration copied and pasted over and as soon as I put the connect tdm t1 0/0/0 0 t1 0/0/1 0 statement in, I drop the data side of the T1 and lose my connection to the WAN. If I take the command back out, the WAN still doesn't come back up until I reboot the router.
Has the syntax changed? I have a case open with TAC but so far no luck, as they can't seem to figure out which group should take this case, voice or data..
ASA 5510 running without issues for a while but we needed extra port so added a 4GE SSM.
Having installed the 4GE SSM we had some issues with the card not liking a connection to our switches and only working by plugging directly from the server into the firewall, not great as we wanted extra servers on the line in the future. So we upgraded the firmware and no are at an impasse.
We have upgraded to 8.0(4)3 and now we cannot get any traffic through the port, we can't even connect to an external DNS server. Running a packet trace I get an immediate error on the first step '(l2_acl) FP L2 rule drop', and it appears as though the outside connection is down.
I have some experience on setting up basic port forwarding and NAT for internet access, webservers, mail but this has thrown me.
I've recently just moved house and we got Virgin Media 50mgs broadband installed with their wireless super hub which is also a Netgear product.However I first noticed up in my room I have weak signal on my wireless devices I have my Dell laptop, xbox 360 and desktop pc with wifi card.I researched this and went out and bought a Netgear wireless extender:
[code]...
Now this does work it gives me excellent signal but it keeps dropping the connection which is extremely frustrating when playing the xbox or on an online game on the pc.I contacted Netgear and all they suggested was updating the firmware
I currently have an issue with the wireless internet at home whilst watching videos, playing online games, completing homework etc... On the computers working over the wireless network there seems to be a randomly occurring drop out of the internet. My home network connection looks to be solid, but the internet drops out for around 5-10 seconds and then comes back.Here is a screenshot from Xirrus the wifi inspector program from the pc in my room connected via the network:[URL]The home network (Munasinghe and family) had a signal of -78 dBm.The second signal, Optus (name of ISP) wifi had a signal of -85 dBm. This signal value often decreases or disappears altogether.
View 1 Replies View RelatedThis is not a problem I would not have noticed save for starting to use Skype. Every 10 to 20 minutes, my internet drops out. This occurs whether my laptop is connected via LAN cable or wirelessly to the router. Skype drops down to one bar, then drops out, and tries repeatedly to redial, sometimes achieving a very scratchy voice call for several seconds before dropping out again. If you redial in 2 minutes, it is fine and achieves medium quality video calls. Whilst skype is floundering around, I can sometimes browse the internet, but sometimes it is offline. I have phoned my ISP and they claim no problems on their end. Beyond that I really don't know where to start on looking for the problem.
View 7 Replies View RelatedWell while browsing net on my mobile/laptop suddenly the Wifi get disconnected. But the wifi of access point does not drops. Its connected to the router in which wifi drops.Also the net on my desktop connected to the router via ethernet cable, does not go offline. I re,ain connected to net via Desktop even when wifi drops.
View 14 Replies View RelatedI had a Linksys Wireless-G router for a long time and had very good luck with it. However, I ended up getting a couple of Wireless-N devices and wanted to get a different router. I bought the Linksys E3000. I got it home and set it up, and at first it worked. Then it would all of a sudden drop everything connected to it. I would restart the router, and in short order it would drop all connections again. This completely baffled me for awhile, until I actually touched the bottom of the router, and it was quite hot. I had it laying flat on a a table, so I could never understand why it was getting so hot. Anyway...I stood it up on it's side and it worked for awhile. Then it would randomly drop various things connected to it. The last straw was when I was listening to internet on the Apple TV, while viewing the internet on my PC and it started dropping the connection every five minutes. Anyway, I have now hooked my Wireless-G Linksys back up and it is working great.
is Wireless-N even needed? I live in a small place, so I don't need it to reach a long distance, and I don't transfer a tremendous amount of date wirelessly, so that doesn't really matter. Should I even try to fix this router? I looked on the Linksys page and I am running the newest firmware.
We have a Cisco 4400 WLC running version 7.0.220.0 and are experiencing clients randomly dropping both broadcast and multicast at the same time. This is not specific to one area of the site and the duration of the MC/Brodacast loss varies. These comms outages don’t happen on all the clients at once but usually affect one client at a time. After a few minutes or a few hours, the client will start receiving the multicast without user intervention.
The site has Cisco 1522 AP's that have rather interesting logs where the DTLS sends fatal errors, followed by CAPWAP going into discovery state. Not sure if this has the same affect or if that's a completely seperate issue.I was told it could be the GTK but I don't believe 7.0.220 has this feature even enabled. The clients are Cisco 3230 and Cisco 1310's. The clients are running version 12.4(25d)JA1 while the 3230 router is running version 12.4(24)T7. What supporting logs or configs need to be shared to better troubleshoot. This has been going on for quite some time and is frustrating the end user as multicast is essential to the operation.
I have a 1841 router connected to an ISP (currently SDSL EFM 10Mbps through an ISP modem, the router and the model are connected with a FastEthernet interface). On another location I have a linux server.There is an ipsec tunnel (3des-sha esp) between the router and the linux server (actually done with a crypto mac).The router has a hierarchical QOS policy on the egress interface.When sending traffic from the network inside the router to the linux host without the ipsec tunnel, everything is working fine and throughput is correct.When sending traffic from the inside network to the linux host internal ip through the ipsec tunnel, some packets are lost and the traffic throughput decrease.When sending traffic through the tunnel in the reverse direction (from the linux host to the internal network), everything is fine.I looked at the QOS statistics and the dropped packets counters don't increase. I looked at the egress/ingress interface statistics and no packets dropped there.I lowered the MTU on the egress interface, but it didn't solve the problem. I played by sending various ping icmp packets size, but even small packets are sometimes lost.I tried to check the router CPU, but it seems relatively fine (<= 10%)I captured the traffic on both side, and I see the packets emitted, and then I can see that some of the esp packets of the corresponding side are not received, so it looks like the cisco router is the culprit. This 1841 router is running: 1841 Software (C1841-ADVIPSERVICESK9-M), Version 12.4(24)T4,How can I troubleshoot where and why those packets are lost?
View 0 Replies View RelatedI have a Cisco RV120W router with 1.0.4.10 firmware. The router drop the internet connections, freeze/timeout in admin interface randomly. How can I determine that this is the router's fault, or if it's the switch / internet access is causing it?
View 4 Replies View RelatedI am running ping between two Nexus 7018 over WAN link ,and I can see some set pattern of packet drop(7.40 % drop) with MTU size 1500.When I ping between my 6500 VSS pair and same Nexus 7018 over different SP WAN link on diffrent location , I am still getting same kind of packet drop (8% drop) with MTU 1500. Has any one else come across this issue with Nexus?
View 1 Replies View RelatedI have a Cisco 871W that periodically will drop its signal. how to configure this for maximum reliability? I set it to use chanel 2462.
View 1 Replies View Related