I have the below configuration for a cisco asa 5505. There is a ADSL router in front of the ASA which has a static IP. I set up a remote-access VPN (using the wizard), but I cannot connect to the ASA firewall as the attached VPN client log shows. My only concern is that there might be something missing, ie a static route that goes to the inside interface. [code]
View 7 RepliesI have a ASA 5505 as a default gateway to a network, whenever I tracert to outside it shows every hop ip address as the ip address I'm trying to get too, quick example
lets say I'm in a 192.168.0.0/25 network but I want to trace to 10.10.10.10
2 Interface (at the moment Same Security Level same-security-taffic permit)
interface Vlan12
nameif STI-Netz
security-level 100
[Code].....
I I try to ping a Host in the ITCS Network (i.e. 192.168.50.10) from the STI Interface I get the error that it failes to locate next hop. I'm quite confused buceause this network are direct attached, so the routes should be fine:
6Nov 30 201215:01:16110003192.168.3.990192.168.50.100Routing failed to locate next hop for icmp from NP Identity Ifc:192.168.3.99/0 to STI-Netz:192.168.50.10/0
We have an internal DNS server that all internal hosts do lookups to .. these requests are forwarded onto open dns for anything the dns server isnt authoritative for.. My question is we have purchased the botnet filter and this requires the asa5505 dns client to be active on at least one interface .. Should i point the asa dns to an external IP such as 8.8.8.8 and apply DNS enabled on interface outside ( am using asdm) I don't want the ASA to control DNS for our internal clients we already have a internal server for this, i DO want the asa5505 to check dns packets against its botnet filter, whilst still using open dns for forwarding.
View 1 Replies View RelatedI have a XP workstation behind my ASA that can not connect to a client's network via Cisco VPN Client using IPSec...
In the logs it shows the translation is working on 500 but the VPN Client has the error 412, that the client is not responding.
Config below
ASA Version 8.2(1)!hostname RWFW1enable password encryptedpasswd encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.1 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address x.x.x.x
[Code].....
I ve configures an asa 5505 for remote vpn with anyconnect. it works just fíne - from remote i can ping the Clients and Server inside, i can do RDP or Connect via SSH to any machine, map some volumes local and so on but: I can not connect microsoft sql server. It uses port 1433 for the first connect and establishes then a dynamic connection. So i am a Newbie - what rules or configs do i miss?
View 3 Replies View RelatedI Have asa 5520 with the code 8.0, the mem shows 94% and the CPU shows 85%
View 5 Replies View RelatedRecently, I have bought an ASA 5505 firewall which I have tried to connect to my ADSL router (Modem).It is now more than a week that I am trying to get internet connection through the firewall but I still can't succeed. I have tried many advices I get from this community but I still don't know what is wrong with my ASA Firewall configuration. From inside I am able to ping the inside and outside interface with a great success. and from my laptop which is connected to the firewall, I am able to ping the both interfaces (inside and outside) but still I can't access the internet.
As I don't have a static IP address from my ISP, I have configured the outside interface to pick up the ip address dynamically. Most of the time, the outside interface get the 192.168.1.2 ip address. [code]
Running ASA 5505
ASA Version: asa844-1-k8.bin
ASDM: Cisco ASDM 6.2(1)
I updated my ASA with version asa844-1-k8.bin.
However, whenever I try and run the ASDM client, I get the following error:
"Your ASA image has a version number 8.4(4)1 which is not supported by ASDM 6.2(1)."
How do I get the latest version installed on my Mac desktop? I know that I can connect via the web interface and run the ASDM client, but the same error persists. I have the asdm-649-103.bin file, but cannot connect to the ASA to install (I don't recall ever setting up SSH).
I am a beginner to ASA. I am trying to connect the ASA 5505 behind the netgear ADSL router which is getting dynamic IP address from the ISP. How to configure the ASA5505 outside interface for SSL VPN connectivity?
View 8 Replies View RelatedI have been working on a configuration for single IP address (on outside ) of ASA5505.I am trying to utilize the outside address 192.168.0.249 to PAT/NAPT to 10 inside machines [code]
What I am not sure of (actually that could be considered all encompassing) is the mapped services/real services.Any constructive comments assistance?
I could get a list of clients on the E3200 wireless (or wired) ports. I have my E3200 setup as a WAP LAN-LAN off a switch and it is not the DHCP server on the network. I can see a list of MACs on the client list, but no client names and no IP addresses. They are definitely named and show up on the WRT54GL (DHCP and NAT) as devices
View 5 Replies View RelatedCompletly new to Cisco ASA and need to get this working ASAP.ASA 5505 8.4(1) is the secondary FW and I need for it to allow everything going out and block everything coming in but for the VPN clients. Since a Cisco moron, I used the ASDM and it's wizards to make this work, which might explain my situation.
[code]....
My Cisco VPN Client connects to the ASA and receives 10.10.101.1 IP address, but I get no connectivity to the ASA or any other 192.168.101.x server or service (tried telnet, RDP, ping, etc.)
I did some searching and the answers said it was supposedly possible but no info on how to do it. I am wondering if it is possible to configure a Cisco ASA 5505/10/20 to be a client to an existing (in this case) cisco client vpn. The reasons why are complicated (and imo irrelevant) but basically I need to be able to make a small network that can be on this vpn rather than individual machines.The client vpn is a basic IPSec over UDP Cisco VPN to an ASA5505.So how would I configure another ASA to connect to this like its a client?
View 3 Replies View Related, I have ipsec vpn setup on an asa5505 at one of my office locations but when I try to log in to the vpn with the vpn client it just dont work but I have a Linux laptop with vpnc loaded and that connects just fine no problems there ? by the way on my windows system i Have vpn client 5.0.07 asa5505 8.0.(4) asdm 6.1.(3)
View 5 Replies View RelatedI want to set up our ASA5505 firewall to allow access from the Cisco VPN Client software.I have nstalled the client software then tried using the VPN wizard to set up the connection without success, I am running Windows 7 32 bit and Cisco client 5.0.03.0530. [code]
View 22 Replies View RelatedI installed on 2 different PCs (Win7 64-bit) the Cisco VPN Client 5.0.07 with the same VPN profile for 2 different users. We use an ASA5505 (8.0(5) sec plus license) as the VPN end point for the clients. The VPN Clients can connect simultaneously to the ASA, they receive the split tunnel infos but only ONE client can ping the internal network ip range. The other one has no access to the internal resources! When they separately try to connect, there is no problem. Each of them can reach the internal net.On other 2 PCs (Win 7 32-bit) the clients have no problem reaching the internal net (simultaneously connect).
View 0 Replies View RelatedI have just purchased and setup a vpn on my ASA5505 and now I wish to setup a Windows VPN client to use it. Does CISCO have any free vpn clients for Windows?I tried to download a client from the CISCO downloads area, but it's for some kind of purchase agreement. I would have thought that the vpn client was free to download given my ASA comes with two free vpn licenses.
View 5 Replies View Relatedwhen it comes to IOS based SSL VPN setup, so have run into an issue which I can't seem to find an answer for.
What i'm after is a way to restrict access to an AnyConnect authenticated and connected client, on a specific profile, to a list of specific websites (all on the Intranet). Everything else must be blocked.
On the IOS device, I had it fudged to pretty much retstrict access to a certain IP and port, and used a mod rewrite in Apache to re-write a URL from that IP to the host the site actually resided on. It's cludged together and working, but it's not ideal (and it's not going to allow for scaling up to what I need).
I can find plenty of references here and on the net to using regex to create block lists based on a global policy to disallow specific URLS, but I need the inverse of that, and, only applied to a specific policy group.
Is this possible on an ASA5505? Is it possible on *any* ASA?
I use VPN Client 5.0.06.0110 to connect my home computer to my office, which has an ASA5505. If my immediate network connection to the PC client is lost while the VPN is active, I get a BSOD. There's no problem if my DSL drops or a cable beyond my router is unplugged. It only (and always) fails if the network cable to the PC running the VPN Client is diconnected (or if my router loses power) while the link is connected.
View 6 Replies View RelatedI have a PCF file that works fine on Windows XP. The tunnel to the ASA5505 comes up, and I can ping my server at 10.1.1.2.
I take the same PCF file and put it on a Windows 7 machine client version 5.0.07.0440 and the tunnel comes up. But I'm unable to ping my 10.1.1.2 server.
Does something in the pcf file need to change for this version of the client?
We have a cisco asa 5505 on which we have setup a group VPN. The VPN connections from all cisco vpn clients works fine except one. The keep getting the below error
"Secure VPN Connection terminated locally by the client. Reason 412: The remote peer is no longer responding. Connection Terminated".
Not sure why only one client won't be able to connect. The version we are using is 5.0.02 for VPN client.
I am working with an ASA5505. I have configured a Remote Access IPsec Connection profile. This profile is configured to give clients a virtual ip address via DHCP as shown in this configuration example: url...When the DHCP request is sent from the ASA to the DHCP server, the hostname in the request is set to the name of the IPsec connection profile and a number. Is it possible to have the hostname set to the host name of the client that initiated the connection?Does the ASA support receiving a hostname as part of a IKE Mode Config Request?
View 9 Replies View RelatedI've deployed AnyConnect on Windows 7 clients, and they are throwing this message after few days of usage: "The VPN client driver has encountered an error."
-Version: anyconnect-win-2.4.0202-web-deploy-k9
-OS: Windows 7 Pro 64-bit
-FW: ASA 5505
What seems to fix it:
1. Uninstall Any Connect Client then,
2. Remove C:UsersUserAppDataLocalCisco folder
We have two sites connect with an IPSec L2L VPN.
-Site A: 192.168.13.0/24
-Site B: 192.168.2.0/24
On both sites we have a ASA5505(Base license) to terminate the tunnel.On Site B we also got a remote access vpn to which we can connect using the vpn client.The lan2lan tunnel works fine and so the remote access vpn.Now i want to connect to Site A using my vpn client connected to Site B. [code] There are no vpn-filters or other special policys in place..If tried to ping from my vpn client to Site A while i was debugging ipsec 255 on site B: the asa matched the l2l-tunnel for traffic sourced from 192.168.25.x to 192.168.13.x but when im doing a show crypto ipsec sa detail there are no packets getting encrypted..so of course no packets reaching my asa on site a.
EasyVPN PIX515 server and ASA5505 client?
View 4 Replies View RelatedI need to configure our ASA5505 firewall for remote access to our network using EasyVPN software installed on a laptop. That laptop will be connected in the different places, using DSL or 3G toggle or Public Wi-Fi. For some people it's very easy, but I don't have any experience with firewalls.
View 9 Replies View Relatedinside network----ASA5505========internet===========Remote VPN client.
The ASA has one public IP on its outside interface and using PAT to the internet. It only has two interfaces, inside and outside using vlan. I created a IPSec VPN through CLI. My goal is for the remote client to browse the Internet throught tunnel.
Q1: Is it possible?
Q2: The remote side gets connected and has IP from the pool, with is part of inside network. But it cannot ping anything, including the gateway, which is the inside interface. I debug it, it shows the ASA receives the ping packages, but it doesnt send anything back to the client.
I have just configured a ASA5505 running 8.2.2 as a webvpn server for clientless VPN connections.
I need to setup a particular bookmark for a RDP session which forces the use of the java client for those who can't seem to get the ActiveX control working for some reason or another (virus scanners/firewalls/scerutiy policies etc).
I created a bookmark as follows, but it always tries to connect with the ActiveX control first when logging on from an IE client.
rdp://192.168.1.1/?force_java=yes
i tried to configured L2TP connection on ASA5505.Phase 1 and Phase 2 are completed but Windows Client doesn't work. [code]
View 4 Replies View RelatedWe are finding the price for ASA 5505 to high and our clients are having problem securing budgets for these devices. We don't want to move to different vendors and we have a team of people we already know Cisco well.I have seen Cisco router 877 which have the ipadvance ios, is this the same as the ASA5505.We would like to offer our clients an alternative to ASA5505, but something which can do the same as a edge device but also protect the client from malicious attacks and has CLI.
View 1 Replies View Relatedi have a question about tunneling a software EasyVPN client to a client ASA Network. It looks like this:
EasyVPN Server 192.168.202.0/24 Network extension mode to Client EasyVPN ASA 192.168.1.0/24 This works fine in both directions. But now i want to connect the client ASA network via EasyVPN software client from outside. The user are already able to connect to the ASA Server on its static outside IP obtaining an IP from a 192.168.21.0/24 pool. This works fine. But how am i able to connect to the 192.168.1.0/24 network from this client?
I have new ASA5520. After configured and upgrade with ASA 8.0(3) image its works for few times (few times means after restarted several times). But now the error comes as "Booting system, Please wait..."
View 9 Replies View Related