Cisco VPN :: VPN From 7965 Phone
Aug 18, 2011
I'm trying to get the phone VPN function working from a Cisco 7965 phone. I can connect fine to the SSL VPN via a normal PC. When I try from a phone, it tries to connect and returns with: "VPN Authentication Failed"
yet, when I look on the ASA with "sh vpn-sessiondb anyconnect" I can see the phone has connected fine:
Username : fred Index : 17
Public IP : x.x.x.x
Protocol : AnyConnect-Parent
License : AnyConnect Premium, AnyConnect for Cisco VPN Phone
Encryption : AES128 Hashing : SHA1
Bytes Tx : 2417 Bytes Rx : 676
Group Policy : SSLClientPolicy Tunnel Group : SSLClientProfile
Login Time : 15:05:53 GMT/BDT Fri Aug 19 2011
Duration : 0h:00m:38s
Inactivity : 0h:00m:08s
NAC Result : Unknown
VLAN Mapping : N/A VLAN : none
View 2 Replies
ADVERTISEMENT
Jul 11, 2012
I've got a 881 working with a 3G Card. Even the Cisco 7965 phone is working well off it. Looking for good doc for configuring the 3G interface as a backup link to Comcast?
View 2 Replies
View Related
Jun 7, 2012
A couple of our remote users are saying that during the day, suddenly their 7965 that hangs off their 881 will start registering for 3 to 5 seconds, then it will be fine.
View 8 Replies
View Related
Feb 19, 2013
I have a CME that has a FXO card, I can call the CME's number from an on-site phone and it works just fine, but when I try from my cell phone it picks up but doesn't give the dial-tone like it's suppose to, but if I hook an analog line to the phone line I can call that no problem from my cell?
voice-port 0/0/0
supervisory disconnect dualtone mid-call
secondary dialtone
timeouts call-disconnect 2
timeouts ringing 30
timeouts wait-release 2
timing hookflash-out 500
caller-id enable
dial-peer voice 201 pots destination-pattern 9T port 0/0/0 and I can see it pick up.
I was under the impression that an FXO card didn't have any clue about inside/outside etc, all it knew was that it was getting a signal to ring.
View 1 Replies
View Related
Jan 6, 2011
I have a CME on the other end of my MPLS network. When troubleshooting phone issues i setup a phone on the CME system in question and point its TFTP server to the address of the CME router. Now, i need to point this phone to another CME but it keeps registering with the previous one no matter what i do (the TFTP server is pointed to the new CME). I have tried turning off the auto register, and i have deleted the ephone and its mac address all together but it always registers with the wrong CME.
The phone is a 7962 with a 7914 expansion module.
View 10 Replies
View Related
Feb 19, 2013
I am moving an IP Phone from one subnet to another subnet.I have deleted the IP Phone configuration in call manager(System version: 7.0.1.11000-2); however, when adding the same device (same MAC address) again in the call manager, the call manager associates the phone with the old IPv4 address (even though the phone is turned off). The phone is booting up and getting a different IP address on the new subnet, and is always in the "Registering" state. The phone has the right CM IP, TFTP IP, etc. the only difference is the phone IP address and the IP address that the CM is showing in the phone device configuration. I also tried resetting/rebooting and restore phone to default factory setting but it doesn't work, i have few more devices on this new subnet that are working fine.
View 5 Replies
View Related
Sep 1, 2011
Is-it possible to manage Cisco phone by web interface? (Manage transfertdiversion... of IP phone)When i go to http://ip_cisco7961 and i give permissions in settings of user (web Access: Enabled)I have only information in read only.
View 4 Replies
View Related
Nov 6, 2012
the customer has CUCM in the inventory database of LMS 4.1. He has all accesses from LMS to CUCM. One phone 7961 is seen in the UT report. When the customer click on the CUCM in the inventory - there is no IP phone registered in the CUCM.
View 2 Replies
View Related
Nov 6, 2012
the customer has CUCM in the inventory database of LMS 4.1. He has all accesses from LMS to CUCM. One phone 7961 is seen in the UT report. When the customer click on the CUCM in the inventory - there is no IP phone registered in the CUCM. What is wrong?:-( See the attachment.
View 1 Replies
View Related
Jan 17, 2012
I have a problem with 9971 phone its works perfect inside network but I cant figureout how to enable VPN on this phone.Also cant found any VPN menu on phone configuration.
View 2 Replies
View Related
Mar 24, 2010
How to do implementation of 802.1x with alcatel phone where pc will be behind the phone and cisco switch ports are configured as trunk. Trunk native vlan is data vlan for pc and trunk carrying voice vlan.when trunk mode is enabled I can not configure 802.1x on trunk interface.
View 1 Replies
View Related
Jan 9, 2013
I try to aquier IP Phone in User Tracking. Phones are present but like pc (without other information...DN, user....)
the LMS version is 4.2.3
the CUCM version is 8.6
the CUCM is green on Topology..
View 4 Replies
View Related
Mar 13, 2011
Currently using PC fax/modem card with landline phone cord to send/receive faxes. I live in a very rural area that has really crappy landlines for my phones. Will be getting a Verizon wireless phone system that has 2 RJ-11 interface jacks so I can connect my current landline phones to the wireless system. Is there some way that I will be able to use my PC fax with this Verizon system? The Verizon salesman wasn't sure but didn't think so.
View 2 Replies
View Related
Nov 16, 2011
Hook my landline phone to my computer.
View 1 Replies
View Related
Aug 20, 2012
I'm just trying to configure my phone that's it
View 1 Replies
View Related
Mar 30, 2012
I am trying to implement a small VoIP LAN (you can see the lan in attachments)for a personal project. I am using:
- 2 x XP (on which i installed Cisco IP Communicator 7.0.3.0)
- 1 x Ubuntu (running GNS3 with a c3600 Router)
The problem is that the phone which is not in the same LAN with the tftp server cannot register.
1) Can a phone register to a tftp server from another LAN ?
2) If the answer for 1) is yes, what am i doing wrong (you can see the details in the attachments)? I mention that the ping works well anywhere in the LAN.
View 11 Replies
View Related
Apr 17, 2013
When I place the phone on a different subnet, registration failed. The connectivity between the two subnet should be working because I have a desktop computer hook up behind the Avaya phone and the computer can talk with the server without problemThe phone has gotten the IP from DHCP server can I can even ping the IP from phone server. but on the phone it shows "Discover 10.0.10.10" then reboot, again and again. 10.0.10.10 is the IP of phone server. And there is no firewall rules blocking the traffic between the two subnet.Like I said before, if I place the phone on the same subnet as the server it worked. The setting of the switch remain unchanged
View 3 Replies
View Related
Jan 8, 2012
I have a questions on an Ip phone when getting the firmware from the TFTP server (e.g. CME) after bootup,- After the registration with CME, the IP phone will getting an auto config file which is the Default.xml file. - The CME will acts a a TFTP server which contains all the IP phone's firmware for different models like 7970 and 7640 in different directories.- The CME have configured with the directory path for all the IP phone when the IP phone come to TFTP and acquired the firmware.Let say I have a phone registered is 7970 and what is the mechanism that governs that my 7970 is not downloading the wrong firmware from the TFTP? Let say it might wrongly downloaded the 7640 firmware? Who take care of this? The phone itself? or the CME will tell the IP phone to take only the 7970 firmware via the Default.xml file?
View 1 Replies
View Related
Mar 14, 2013
Is it possible to connect an analog phone to an FXS port on a CME router and a VoIP phone to a switch connected to said router and have voice connectivity between the phones? Also, is it possible to connect an FXO port on that same CME to a RJ-11 wall jack to connect to the PSTN and be able to call that VoIP phone as well as the analog phone from my cellphone? I'm trying to tie as I read the CCNA Voice OCG.
View 5 Replies
View Related
Apr 22, 2011
i have a wlse setup in a small orgnization and have c1130 aps connected to lan netwrok and with two broadcast ssids,and i have cisco ip telephoy setup too, now i want to connect some of cisco wireless phone to connect through the wireless,as i said that i have two ssids and both are working very fine,so my question is that on lan switch side i have configuration:interface GigabitEthernet1/0/9 switchport trunk native vlan 54 switchport trunk allowed vlan 51,54,58,59 switchport mode trunk spanning-tree portfast.
View 2 Replies
View Related
Apr 20, 2012
We have bought L-ASA-AC-PH-5520=Anyconnect Vpn Phone License for our Cisco Phones but when we entered this license into our ASA it shows th following i.e enabled for linksys phones. Is there a diff part no to enable vpn for cisco phones. [code]
View 2 Replies
View Related
Mar 26, 2013
I'm playing with an SF300-24P switch and want to connect an IP Phone. I'm more familar with IOS syntax than the SF300 GUI.
How would I replicate the following in the SF300:
Switch(config)#int fa0/1
Switch(config-if)# switchport mode access
Switch(config-if)# switchport access vlan 15
Switch(Config-if)# switchport voice vlan 5
Not sure if setting the port to an ACCESS port on VLAN 15 (i.e. 15UP) and having the Voice VLAN set to 5 is correct.
Or should the port be set to General or Trunk with 15 as the untagged VLAN and 5 as the tagged voice VLAN (i.e. 15UP, 5T)?
View 2 Replies
View Related
Feb 21, 2011
I am piloting an 802.1x implementation for a client who has Mitel IP Phones. I have setup the switch and ACS based on previous experience and a windows PC can authenticate onto the network OK. When I use a Mitel phone however, it seems to skip past the first 802.1x LCD message and goes straight to LLDP and DHCP discovery, which obviously fails. The phone are 5224s and the controller is on the original v10 release. I have cleared the 802.1x config on the phone and rebooting as per Mitel documentation which leads me to believe it should then prompt for a user/pass on next reboot. It does not do this.
I known the ACS is setup to support EAP-MD5 and I have tried all the various types of host modes including the default and Multi-Auth, Multi-Domain and none of them seem to make any difference. I have tried with and without a PC attached to the phone as well.
A wireshark shows the EAP identity request from the switch, and I see an EAP response from the phone, although it is slightly different to the PC's response. In the end the phone issues an EAP 4 failure message. So something in that EAP conversation doesnt seem to work.
View 1 Replies
View Related
Feb 22, 2011
We have a Cisco PIX 515r and currently our users install the Cisco Client on their desktops/laptops and connect to our VPN.
Now I'm being told I need to set up a VPN tunnel for a remote IP phone. What I need to do on the PIX for this
View 4 Replies
View Related
Jun 6, 2013
How to confirm the linceses required for me to get this working. I understand that it needs the 'AnyConnect for Cisco VPN Phone' license but do I also need to have anyconnec essentials? This is for ASA version 8.2 and the a license info below is for the ASA i intend to delpoy this on. This platform has an ASA 5550 VPN Premium license.
View 2 Replies
View Related
Apr 4, 2012
I have an ASA 5510 running 8.2.2 code with 30 VPN Phones connected. Of the 30 phones, I have 5 that do not negotiate DTLS and I'm having quality issues with these phones. I've checked the login process and I don't see any errors when these phone connect, they just don't even attempt DTLS. All the phones use the same VPN configuration.
View 4 Replies
View Related
Sep 27, 2011
We just installed MSE with CAS (7.0.201.204 software) and everything works fine and clients are shown on WCS floor maps except for Cisco 7921 wireless phones which dont appear in the WCS map.
View 3 Replies
View Related
Oct 26, 2011
authenticate phone Mitel in ACS 5.2. I tried to authenticate a PC wich is behind of phone Mitel, but it doesn´t working.the solution work fine with vlan mapping.
This configuratión work fine with Phone Cisco but not for phone Mitel, and I had used this templace by both.
vlan 709 = guest
vlan 10 = voice
inter fas 1/0/8
switchport access vlan 709
switchport mode access
switchport voice vlan 10
[code]....
View 1 Replies
View Related
Mar 9, 2013
have configured Cisco IPPhone 7925G with EAP-TLS setting. (With manufacture installed and Userinstalled certificate). My issue is while roaming from 1 AccessPoint to another AccessPoint the call getting droped. I need to restart the IPPhone to reauthentiate again. In ACS am agging the authentication time-out error. (I had changed the time out value for EAP-TLS to 20 in WLC as per recommendation.)
If am using static web key there is no issue in roaming.
What is the reommended setting inorder for the EAP-TLS to work properly.
View 2 Replies
View Related
Feb 21, 2013
I am just getting more confused the more I try to work it out. Not sure if this goes in the IP Telephony section or here. We have an ASA 5510 with the base license. We are needing to install IP Phones at remote workers homes, and I understand there are Cisco IP phones which have VPN clients built in to allow a tunnel to the central private network. IT appears that you can only use Any connect VPN for this, ans I am trying to work out what licensing upgrade we need to apply to the ASA, as the two Any connect licenses you get free on the ASA is not enough.
This is the phone we are looking to get; {URL} . What I want to know is will the Any connect Essentials license work with these IP phones? When I do a show version,
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 50
Inside Hosts : Unlimited
Failover : Disabled
[code].....
This platform has a Base license. It shows "Any Connect for Linksys phone : Disabled", is this the same for Cisco IP Phones? Is this the specific licensing type I should be looking to get for Any connect on IP phones or will Essentials do?
View 4 Replies
View Related
Apr 15, 2011
bought a new usb cable for samsung champ to connect to hp 620 notebook and installed all necessary things and now it does not charg the phone
View 2 Replies
View Related
Jul 30, 2012
I've got a digital phone system but it goes VoIP across our P2P T1's. I am having quality issues between our 2 sites only and have decided to setup QoS on the Cisco 1841 P2P routers. each side that does the voice traffic, I would like to do QoS by IP address, instead of by protocol.I will need an access-list, a class-map and a policy-map and need to point the interface to the policy-map
View 19 Replies
View Related
Jan 24, 2011
Any way to simply have someone phone my computer such that they're on a cell and I'm on my mic? It seems like such a simple thing for this day and age, but my attempt at a Google search is resulting in things that aren't exactly what I mean, such as where I can phone them first, but would have to incur charges, as if I'm using a cell myself instead of a mic. Any way, a site, or a software, to make such a setup work? To be clear, someone using a cell phone--not a mic and not a computer--would somehow "phone" my computer/a software I have, and I would hear them through the speakers as usual and communicate by my PC mic--not a phone and not a cell.
View 2 Replies
View Related
