Cisco VPN :: Setting Up VPN On 851 W-G-A-K9 Version 12.3?
Dec 22, 2011
setting up VPN on my CISCO 851 W-G-A-K9 version 12.3 ?I read on the cisco site that it supports VPN and L2TP and PPTP Tunnels?I did a show VPDN and itt shows no tunnels setup?I use a hyper terminal connection and make all my changes via command line?
I run a windows 2003 server environment with active directory that I have some remote users that I would like to logon to the network?I also have a laptop that I would like to take on the road and be able to logon via vpn?what commands would I need to set this up
I can do simple command like
enable
conf t
ip nat inside source static tcp xxx.xxx.xxx.xxx 25 interface FastEthernet4 25
exit
wr mem
enable
McAffee scan of acs 1113 appliance running the 4.2 build 124 patch 12 version reports that a medium vulnerability exists because the system has SSH version 1. Any way to specify only version 2 or turn off SSH?
We are looking to upgrade our WiSMs to version 7.0.230.0, but the Cisco compatibility matrix suggests we need to upgrade WCS to the same version (it is currently on 7.0.172.0). My question is can we upgrade the WiSMs and do the WCS at a later date with no issues or do we need to do them at the same time to keep visibility of everything?
The reason I ask is that some of my clients use lobby ambassador for some of their users and they will need wireless access on the day we are due to upgrade WCS (the WiSMs are due to be upgraded and rebooted earlier that morning.
I'm not sure how to tell if I'm running ssh version 1 or ssh version 2, or both.I thought a show run would show a line like, "ip ssh version 2" or "no ip ssh version 1", but I don't see these anywhere.
issue with their ASA version 8.4.2 code? I loaded this code on my beta ASA last week and have seen it "hang" twice since the upgrade. The previous versions of 8.3 and 8.4 code on this same ASA did not have this issue.
I configured the below in IOS ver 12.4(5a) is working fine (able login using Putty) , but the same configuration is not working in IOS ver 15.0(1)M2 (Not able to login using Putty)
hostname hostnameip domain-name domainnamecrypto key generate rsa ip ssh time-out 120 ip ssh authentication-retries 2
I am trying to SSH into my controller after upgrading to 7.0.103 and I get the username prompt but it seems to be disconnecting as soon as I do. Is there something different about this version of code as opposed to the older ones?
WCS fails to start with a Tomcat error , see below ;See launchout below - without re-installing WCS
Checking for Port 21 availability... OK Checking for Port 8456 availability... OK Checking for Port 8457 availability... OK Checking for Port 1299 availability... OK
I have a couple of Cisco WS-C3750G-12S-E, I`m putting to use again. These will be doing routing (IPv4 and IPv6), VLANs, VRF etc etc.
In Cisco Feature Navigator I find that the newest IOS for this model is 15.0(1)SE and 12.2(58)SE. But my supplier says c3750-ipserviceslmk9-tar.122-55.SE3.tar is the latest. What is the most feature rich, best, stable image I can load on this unit.
We are trying to make a VPN failover over two ASA's. However the 2 ASA's have different version and our smartnet have already expired. I was wondering if this VPN failover would work even if they are different? Or should I get a smartnet first to be able to download an updated ios?
I thing that i find some bug in the newest IOS 15.1.4M.
The case is falow:
I start to configure failover for the costomer - make default route, make the default path but i cant find the comand IP SLA monitor. Is some meet this problem with this IOS or just Cisco make some chenge in the CLI commands?
I have a routing problem here with routing in PIX515E version 6.35. I have some Client PCs located in the DMZ interface of the PIX515E, they connect to PIX using Cisco VPN Client (IPSEC VPN), after that these PCs can be routed to access Servers (static route) located behind Internal interfaces of PIX. I have some Servers located remotely having Internet Access, the gateway router remotely connect to PIX Outside Interface (Internet) using IPSEC VPN then routed to inside Interface (static route).
I' have realy big layer two access network made of etherogenius Cisco switch with different IOS version and train.My customer bought ISE (ADVANCED AND BASE LICENSE).As far I read on DS it is seem that if you have Minimum IOS release 12.2(52) SE you are able to perform COA, reading DS with more attention I notice that cisco raccomend IOS versione 12.2(55)SE3 why ? does it means COA does not work with 12.2(52)SE,I need a minimum IOS release to perform 802.1x on my wired network ?
I would like to know whether CSM 4.3 is compatible with ASA version 9.1(1). Any appropriate url that contains information about these two version's compatibility?
I try to convert a CISCO ASA 8.2 version to 8.4 BUT, I have a small or "little" problem :On Cisco ASA 8.2.x, i have a possibility to create multi-line global with different subnet.Example :
global (outside) 2 217.1.x.65-217.x.x.66 netmask 255.255.255.240 global (outside) 1 interface <-- Ip interface is other subnet : 217.3.x.3 global (outside) 2 217.1.x.67 netmask 255.255.255.240 nat (inside) 1 0.0.0.0 0.0.0.0 nat (dmz2) 2 192.168.4.0 255.255.255.0
What is the method or solution to translate multi-global in 8.4 ? with static translation in 8.4 : i try to use different server in inside's zone, but not in same network on outside. In 8.2 Firmware, it's very easy to use that, but in 8.3-8.4 version, i don't have some idea to manipulate ...
interface Vlan1 description Lien vers reseau Interne Client nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0
I have been using ASDM on a "Cisco Adaptive Security Appliance Software Version 8.2(5)" for a long time and in order to route packets among the interfaces without NATting the packets, I have always been using the function "Add NAT Exempt Rule" under "Configuration -> Firewall -> NAT Rules". Everything has always been working fine.
Now I am trying to use ASDM on a "Cisco Adaptive Security Appliance Software Version 9.1(1)" and I cannot find how to do the same operation: the "Add NAT Exempt Rule" option is no longer available and the only way to make the traffic passing through seems to be NATting it on the OUTSIDE interface.
where I am mistaking? My goal is to let the traffic passing through from the inside interface to the outside interface without being translated.
We want to make an upgrade of one of our customers' ASA 5520 (with failover). They have version 8.2 now and we want to get the more stable newest one. Can we get an 8.6 version? or we need an ASA 5500X for that one?
I was trying to search for cisco vpn client version 5.x for MAC OS but only saw the latest version at 4.9. If version 5 is out for MAC? Also, what the latest possible version of the vpn client is for MAC that is compatible with both the vpn 3080 concentrator and asa5580?
For quite some time now, we have been experiencing an issue with the Cisco VPN client that will make the client completely unusable. I have noticed that when a specific feature of Symantec Endpoint Protection is enabled, it will (about 25% of the time) cause the following errors to appear when attempting to connect anywhere with the Cisco VPN client. Once this error happens once, the VPN client then becomes useless.
Error #1 Reason 414: Failed to establish a TCP connection
Error #2 Reason 440: Driver Failure
Error #3 Reason 442: Failed to enable virtual adapter
It seems that fixing one error will cause the other error to come up.I have tried reinstalling the client with the same version and older versions and the issue still comes up. All users in the company are using Windows 7 64-bit with SP1 installed.The oddest thing about this is that all employees in the company have the same antivirus with the same features enabled, however, it only happens to a small percentage of employees.
%ASA-3-305005: No translation group found for tcp src inside:211.155.169.186/1433 dst outside:42.121.87.89/6000, I found this error ,but the IP 211.155.169.186 is public address. I check the configuration but didn't find any information about this address.I don't understand why src is inside? How can I solve this error?
I have a C2950 Switch & I am trying to upgrade the IOS version of it so that I can proceed with learning about SSH. My current version of 12.1 does not have Enhanced Imaging. I am so new to Cisco, that I have spent hours trying to find the correct page, or link, or anything that can enable me to upgrade to a later version.
configuring Cisco AnyConnect VPN? For some reason with the config below, I seem to get connected but then my internet connection randomly drops and reconnects. Ive tried several different times to get this to work properly but Im obivously missing something here.
We have 2 firewalls on PIX facing the Internet and connected to interface e1 (behind it) an ASA version 8.3 Both the PIX (Firewall facing) and the ASA are on the same subnet.
By using Routing statements and statics I have been able to reroute specific traffic to the ASA5520 version 8.3 Now I need to inverse the 2 devices. The ASA5520 will be facing the Internet and the PIX will be behind it.Unfortunately the ASA5520 is refusing to route the traffic to the PIX. The access-lists are open accordingly and a NAT on the ASA has been created.
