I just replaced 2800 router this did not have a VPN hardware accelerator with a 3925 that does have a VPN accelerator built in. I copied the same VPN (ISPEC/ISAKMP) config from the 2800 to the 3925 and it works. Is there something special I have to do to enable the hardware acceleration or is it automatically used for every VPN session?
View 1 RepliesI have some simple rules on 2 extended lists:ip access-list extended FWINpermit tcp any host 192.36.86.231 eq ftp-data ftp 22 www 443 516 666 671 672 2222permit tcp any host 192.36.86.231 eq 4500 8008 8443permit tcp any host 192.36.86.231 range 5900 5950permit tcp any host 192.36.86.231 range 33434 33550permit tcp any host 192.36.86.241 eq ftp-data ftp 22 www 1935 2195 3306 8888permit tcp any host 192.36.86.241 range 8080 8090permit tcp any host 192.36.86.241 range 33434 33550ip access-list extended FWOUTpermit tcp host 192.36.86.231 any eq ftp-data ftp 22 www 443 516 666 671 672 2222permit tcp host 192.36.86.231 any eq 4500 8008 8443permit tcp host 192.36.86.231 any range 5900 5950,The issue is that 192.36.86.231 can access internet, and 192.36.86.241 can not.Is there a way to troubleshoot 192.36.86.241's connection/packets flow?
View 1 Replies View RelatedWat will be the default memory and hard disk for SM-SRE-710-K9 and wat will be the maximum support for this module.
View 1 Replies View Relatedprovide my some (official) info regarding the MBTF for the C2900 and C3900 routers (2911 and 3945)? This info is currently not part of the data sheets.
View 0 Replies View RelatedOn my 3900 Router my port seen to be shutting themselves off, they are connected antenna.
View 2 Replies View RelatedThe datasheets indicate that the 39xx series ISR G2 routers support AES, but they don't indicate if they handle both AES128 and AES256 in hardware. Via our account manager, we've heard that they only support AES128 in hardware, but not AES256. Given there's no equivalent of an AIM-VPN/SSL-3 module for a 39xx router, this could be a problem for a deployment we're looking at doing.
I can find no document anywhere on cisco.com that confirms that AES256 specifically is supported IN HARDWARE on, say, a 3945E router.
And, if it is supported, are there any performance numbers available for throughput? We're trying to find out if a 3945E is appropriate, or if we need to go with a 7206VXR w/NPE-G2 and VAM2+ module.
I have a cisco 3900 integrated services router. I am a little new to the cisco IOS. I am having an issue getting my LAN network to communicate with the WAN gateway. From hosts I can ping the interface IP address but not the gateway. I have used the default route command of IP route 0.0.0.0 0.0.0.0 [wan gateway from ISP] I have already set up NAT, DHCP, I just cant seem to get the internet working, the following is my config.
Code...
i have a cisco router (3900 series) and a add on module (4 x 1 Gig port module). For some reason i cant seem to port channel them and cant do routing (can set an ip address on those ports). I can do port channel and routing on on-board ports. Do i have to enable any commands to do this ?
View 3 Replies View RelatedI am trying to configure ISP failover using IP SLA tracking in Cisco 3900 router(C3900-SPE100/K9).
I want to configure below commands:
R1(config)# ip sla 1
R1(config)# icmp-echo 2.2.2.2 source-interface FastEthernet0/0
R1(config)# timeout 1000
[Code].....
configure IP sla static route tracking in Cisco 3900 series router.
I am setting up a DMVPN between several dozen sites using 2800, 2900 and 3900 series ISRs. The DMVPN Design Guide recommends current 12.4 or 12.4T IOS, but the DG was last updated in July 2008. I cannot seem to find any recommendations newer than this. I'm hoping Cisco or the community can give me an updated recommendation.
View 5 Replies View RelatedI run streaming multicast video cameras on my network. I stumbled upon the command ip multicast rate-limit. When I configured a test setup in my lab (multicast camera source and a few routers) and tried the command it simply did not work. Moreover, when I went to use the command on a 3900 router in my lab, it was not there.
I take it this command has been deprecated?
I've been trying to find the right information on Cisco's site, and I'm not having success.
We have a 3900 router that we would like to do authentication via a local userdatabase. We want ssh access and console access using a local user on the router. I've been working on the console piece and everytime I try it, I get prompted for a username, but it is not accepted.
i have a gateway router going to the internet....using public IP addresses on both interfaces. starting on Monday, traffic would suddenly stop flowing from the inside of the network going out, though i can still ping the outside interface , but when I log in to the router I am able to ping to the internet. so its like traffic is not passing from the outside int to the inside int. I have a 3900 router. other thing is, when i restart the router it will work for some time and then just stop again....
View 6 Replies View RelatedAny actual limit on the number of IPSEC SAs that can be negotiated on the crypto module of a 3900 series G2 router? When I issue the command on a 2900 G2,This implies the 2900 series can handle 1800 IPSEC tunnels with an SA used for each direction. All of the documentation and support requests have stated that the crypto module is better than the AIM module in the older series routers but I have been unable to get a concrete answer to the limit.
View 21 Replies View RelatedHow many ipsec tunnels are supported in Cisco 3900 routers(with & without the hardware processors)?How much is the throughput of the 3900 routers?
View 1 Replies View RelatedI am in search of a 1 Gig Ethernet WAN module for 2900, 3900 series router.I want to terminate 230mbps link on this module.I found EHWIC-1GE-SFP-CU option but as per service provider it will not support to 230mbps link.
View 3 Replies View RelatedAm trying to do a dynamic configuration of a 3900 series router (3925 to be precise).For the software and licenses, under the IOS technology Package Licenses, what's the significant of SL-39-DATA-K9 and SL-39-SECNPE-K9? Are they really necessary for the router?
View 3 Replies View RelatedWe currently have a single data centre with 2 x 100Mbps internet links from a single ISP. The 2 links are routed and terminate on separate ISP switches/routers with a /30 IP address, the links terminate on 2 Cisco 3900 series routers in the DC. eBGP and iBGP has been configured to provide high availability. We are currently using a private BGP ASN from the ISP and /24 subnet which is routed to the primary 3900 router and to the backup 3900 router in the event of a primary router failure.
We are looking to add a second data centre for DR and we need the /24 to failover over to the DR data centre in the event that the primary DC fails. The second DC will only have a single 100Mbps internet connection as resiliency in DR is not required. I understand how eBGP/iBGP willl be setup and configured for both sites but I would like to know the pros/cons and peoples experiences of using a single ISP to provide internet connectivity for both Data Centres? I understand that I will need a public ASN if I use separate ISPs.
Is using a single ISP for all 3 internet connections acceptable? The circuits will be connected to resilient parts of the ISPs network. If we decide to use a second ISP, would it be recommend to use ISP1 for the Primary and DR data centre primary links and ISP2 for the Primary data centre backup link?
I am looking for the procedure of the router 3900 series failover. I have got two 3900 series router with the same ISO and other interface cards. What are the main things that I should watch ? Does the standby router takes the same ip of active router if the active router fails ? How should I configure it.
View 1 Replies View RelatedI would like to configure the policy base routing (PBR) on router (3900) base on the "specific tcp port" (TCP port 16255) to re-direct the traffic to another FE port.
From cisco web portal, CAT 4500 should support PBR as below:"Policies can be based on IP address, port numbers, or protocols. For a simple policy, use any one of these descriptors; for a complicated policy, use all of them." url...
Does 3900 router has the same features on the PBR? if yes, can it support "source tcp port" and/or "destination TCP port"?
I recently upgraded from a Cisco 3900 series router to a Cisco ASR1k router. Since the upgrade, I have internal clients who claim they cannot connect to external VPNs. These internal clients are behind a NAT that routes a public IP address to a group of clients with private IP addresses.
How can I ensure that all VPN traffic is able to pass through the NAT?
how to go about config my bureau connected to HQ and separated by a WAN link of 60mb.
This is my plansplit into halves that is 30 mb for LAN connections, internet and file serving for strictly video streaming, bureaus have routers 2800 conected to HQ HQ has a router 3900
1. We have Two 3900 Router on the core layer which are terminated with one ISP on one Router and Secondary ISP on Second Router.
2. Can we configure my ASA 5520 with Active/Standby termenating two IPS providers one on Active ASA 5520 and Other ISP on Standby ASA 5520, so that when Active ISP fail ASA Secondary can become Active and send the Traffic throough Secandary ISP.
3. The reasion behind giveing Public IP on Firewall is to Terminate VPN on our Firewall i.e. SSL and IPSEC VPN.
Few Clarification If we can achive the above:
1. How will the DMZ Servicec nated with my Primary ISP on my Primary ASA will be routed when the Secondary ASA is acting as Active Firewall.
2. Can Web SSL and Client To Site IPSEC VPN users access service via the Secondary ISP- ASA when my Primary ASA and ISP is down.
We are migrating from a Microwave T1 WAN to a Fiber ring WAN which I'll be connecting to our providers Ciena Metro E switches. Eventually we are going to move away from the routers, but the network is a little too complex as well as spanned across a lot of miles. Since I am the only networking personnel here, I would like to first simply migrate to the fiber by simply moving the connection configs off of the T1 interfaces, and onto one of the Gig interfaces on the 7206 and on one of the Fe interfaces on the 3900 (which is actually a 3700 series because the line card on the 3900 is toast). If this works, I will need to purchase Fe line cards for the 7206, because I found out that the virtual interfaces do not support Policy Mapping for our QOS and Multicasting.
View 6 Replies View RelatedTransitioning from 3825 to 3945 (OS is 15.0(1r)M13 c3900-universalk9-mz.SPA.151-4.m4). Turning on FDL on the 3825 was easy but the same command on the 3945 doesn't work.
View 3 Replies View RelatedCan the 3900 series router be ordered or upgraded to a license with advances enterprise services? I have a few of these routers and I'm looking to get the license upgraded if possible.
View 1 Replies View RelatedMy Cisco 3900 router is not taking the no auto summary command?
View 5 Replies View RelatedNow, I use Catalyst WS-C3750G-12S-S as BGP router. But it is switch do not support in higher 65535 (32 bit asn). In future, I plan to use two or three ISP (each will be connected through 1Gb uplink). I need a router, who will be support 32 bit AS number and work with two or three full view BGP tables. I look at Cisco 3900 series, and ASR1002F.
View 2 Replies View RelatedI know this is not a the preferred way to do it, but this just an interim network configuration until the Remote Site gets re-located and reconfigured. I'm trying to bridge and route traffic and hoping the community can offer a review of the sample configuration and/or some ideas to make this a reality.
Existing network is bridged across site-to-site private line (p-2-p) so 192.168.100.0/24 devices exist at both locations. In order to reduce bandwidth consumption across the p-2-p, the 172.20.100.0/24 devices (end user PCs and new to the environemnt) will be routed out a local Internet connection which in turn reduces the p-2-p traffic to just private network traffic for the two networks. That same network requires routing through the 192.168.100.0/24 network in order to access the private WAN connected to the 3900 router with IP 192.168.100.1.
Is there a router (1900-3900 series router) that will support a 100FX fiber connection. We use to use 2800-3800 and 2600-3700 series routers with FX fiber interface now these routers are no longer available and our need for 100Mbps FX is still a requirement.
View 3 Replies View RelatedI have a question concerning about how many ospf and bgp route entries does 3945E isr g2 router support?
View 6 Replies View RelatedI faced some problems when updating the device packages on the LMS 3.2 server. Therefore, I really need device packages of switch 3750, router 2900 and router 3900 series. I had tried update online but could't view any devices.
View 1 Replies View RelatedCisco 1900 , 2900 and 3900 have Interface Slots and Service Module Slots , My question is which type of card is support this slot.
View 6 Replies View Related