Cisco WAN :: Can't Connect VLAN Interface On 881 To L2tpv3 Pseudowire
Jun 21, 2010
I'm looking to build (cheaply) some l2tpv3 tunnels across a campus network. I have a pair of 881's and I was hoping to xconnect the VLAN 1 intfcs between the two of them. "xconnect" is not a CLI option on the interface configuration, although it is for the individual Fa0-3 interfaces. Just for grins, I xconnected the l2tpv3 tunnel between each Fa3 on each router, and the tunnel comes up successfully and I can see a session established. I am routing between the WAN interfaces (Fa4) on each. However, L2 traffic is not passing between the two Fa3 interfaces. I can do it backwards, i.e. route between the Vlan1 interfaces and xconnect the Fa4 interfaces (i.e. WAN), and I can see broadcast traffic from the destination network appearing on the local interface. However, I'd really rather have the four interfaces in VLAN1 tunnelled rather than the WAN interface. I am guessing this has to do with ISL vs. 802.1q, since I'm trying to encapsulate VLAN1 as Ethernet and not as dot1q.
View 8 Replies
ADVERTISEMENT
Jun 13, 2011
I am trying to setup a L2tpv3 VLAN-to-VLAN tunnel.My setup has two Cisco 890 router with Cisco IOS Software version 15.0(1) M4. These routers are connected directly on FastEthernet port 8.
One linux machine is connected on FastEthernet port 0 on each router. The two linux machines are on same vlan. I am trying to establish a vlan-to-vlan tunnel between the routers and send traffic between the linux machines.
I followed the case study 11.4 from [URL] and configured the l2tp-class and pseudowire-class. However, the vlan interface configuration is different on 890 router.
I configured a vlan interface as follows.
(config)#vlan 200
(config)# interface FastEthernet 0
#shutdown
#switchport access vlan 200
(config)# interface vlan 200
I don't see the 'xconnect' command in this context. What's wrong with my configuration?
View 3 Replies
View Related
Oct 30, 2010
I have a subnet (vlan 104) working great across a WAN. At site 1, Router A (3745) has the L2TPv3 tunnel configured while Router B (7204) has a routed interface on vlan 104.
The only thing router A is doing is the tunnel, so I'd like put the tunnel on Router B and eliminate Router A.
The trouble is, when I move the configs to Router B, the tunnel comes up, but the far side does not receive traffic over the tunnel.
Router B shows sending and receiving packets (per the 'sh l2tun session all' command). The far end router shows sending packets but receiving 0.
Is it a problem to have both the vlan 104's L2TPv3 xconnect interface and the vlan 104's routed inteface on the SAME router?
View 10 Replies
View Related
Nov 21, 2012
i'm going mad on following problem. I'm trying to get 2 networks seeing each other while one of the network is a non VLAN network and the other one is a VLAN network.They should use the same interface so i added VLAN e0/0.122 to the interface e0/0.Send a ping from my asa to both gw-IP's made me happy at first. In second in figured out that i cannot reach any client in the other network. For testing purpose i created an permit acl to any/any for both networks, but the packets still get dropped by the default implicit rule. (deny any/anyMaybe i'm to stupid for this
View 10 Replies
View Related
Oct 18, 2012
Does L2TPV3 will support multicast?
View 3 Replies
View Related
Sep 6, 2011
I have 2921 with SEC feature set ( version 15.0(1)M4 ) and want to configure l2tp tunnel, LAC to LAC scenario. It does't have pseudowire-class command. Does it require another license or commands ?
View 3 Replies
View Related
Jan 18, 2011
I was found the different IOS support L2TPV3 tunnel ID, like 12.2(33)SRE is support 32bit, 12.4(15)T is support 16bit.so the 12.2(33)SRE can't xconnect/l2tpv3 to 12.4(15)T.
I found the 12.2(33)SRE Local Tunnel ID is over 65535, how about reduce it less 65535? or some other suggest to xconnect/l2tpv3 on different IOS?bcoz using same IOS series is normal. like 12.4T and 12.4T / 12.2SRE and 12.2SRE
some result is following.
12.4(15)T:
xxxx#sh xconnect interface gigabitEthernet 0/2.209 detailLegend: XC ST=Xconnect State, S1=Segment1 State, S2=Segment2 StateUP=Up, DN=Down, AD=Admin Down, IA=Inactive, NH=No HardwareXC ST Segment 1 S1 Segment 2 S2------+---------------------------------+--+---------------------------------+--DN ac Gi0/2.209 209(Eth VLAN) UP l2tp 152.xxx.xxx.120:500 DN Interworking: none Session ID: 15758 Tunnel ID: 60524 Protocol State: DOWN Remote Circuit State: DOWN pw-class: vlan-xconnect
xxxx#sh l2tun tun
[code]....
View 1 Replies
View Related
Jul 11, 2011
I'm currently using DLSW to bridge a VLAN to a remote site and it works fine. I've been reading up on L2TPv3 and now I'm wondering if one is better than the other for my purposes (my hardware will support both), especially if multiple VLANS are being bridge to the remote site. We do not have an MPLS infrastructure, so that's not an option.
View 2 Replies
View Related
Dec 18, 2011
I have Cisco router 851 at my region site. It has five Fa ports. One of them is connected to ISP and has ip address 10.1.1.2 (for example). It also has vlan 1 interface, that has ip address 192.168.0.1 (also for example). I also have Tun0 interface that goes through ISP network and connects to my hub network. The rest of Fa interfaces are swithcable and they are in vlan 1.The problem is that from hub LAN I can telnet to 10.1.1.2 ip address, but I can't telnet to 192.168.0.1. Whereas I can Ping 192.168.0.1 from my hub LAN.
Topology:
Hub LAN -------ISP---------Spoke Router 851
View 8 Replies
View Related
Aug 8, 2011
come to a bit of a block in the road on a network im building ,all is going well except i need to build a pseudowire to backup our primary L2 circuit, I labbed this with some 3745's but the kit we are using is the 1921, with the universal image how do i go about upgrading functionality to allow this [code]
View 4 Replies
View Related
Jan 12, 2013
How to apply access list on Vlans ?
my Scenario is
13 Vlans in cisco 3560 switch (Vlan 10,20,30........ 130)
vlan 10 ---- ip range 192.168.10.0/24 interface vlan 10 ip add : 192.168.10.1
vlan 20 ---- ip range 192.168.20.0/24 interface vlan 20 ip add : 192.168.20.1
here i want to block vlan 10 access to vlan 20 i created extended access list deny ip 192.168.10.0 0.0.0.255 192.168.20.0 0.0.0.255
and applied in interface vlan 10 as out now i cant able to access any host in vlan 20 (host 192.168.20.1) but i can able ping vlan 20's gateway 192.168.20.1
View 3 Replies
View Related
Dec 7, 2010
I am trying to roll out a new internet router. The problem I am faced with is the LEC only supports VLAN 1227 and greater, specifically they are assigning me VLAN 2528. I am able to create the sub-interface and setup dot1q encapsulation for VLAN 2528, but the vlan database does not have the ability to add VLAN 2528 to it so I am unable to get layer 2 up and going, thus preventing me from getting the implementation done.
View 11 Replies
View Related
Mar 19, 2012
i have linksys modem which already working for different v lans then for lab we take other switch 3750 switch and created different v lans. v lans are working fine but we need internet for different v lans for that linksys modem how we can make interface V lan1/
ip address 10.1.1.10 255.255.255.0
ip default- gateway 10.1.1.1
no sh
interface Vlan10
ip address 10.1.2.1 255.255.255.0
no ip route-cache
!!interface Vlan20
ip address 10.1.3.1 255.255.255.0
ip route 0.0.0.0 0.0.0.0 10.1.1.1
ip dhcp pool vlan10
network 10.1.2.0 255.255.255.0
default-router 10.1.2.1
dns-server 10.1.1.1
!
!ip dhcp pool vlan20 network 10.1.3.0 255.255.255.0 default-router 10.1.3.1 dns-server 10.1.1.1
View 1 Replies
View Related
Apr 22, 2013
Actually I am new to this ASR , in my environment my 6513 is connected ASR , I want to know how can we access and configure VLAN on Gigabit interface which is connected to 6513.
View 9 Replies
View Related
Aug 9, 2012
I'm trying to set up a Guest VLAN for wireless at a client site, and I feel like I'm missing something small in the configuration, since I can't ping any of the VLAN interfaces from my laptop when the address is statically set to something in the 172.20.100.x range.
I've pasted the configs for the ASA 5505 and the 6 switches below for convenience. Near as I can tell, all should be well. The ports are in trunking mode, the "show cdp neighbors" command returns the proper information, VLAN 100 exists on all the switches, etc.
Code:
ASA Version 7.2(4)
!
hostname ASA
domain-name xxxx.local
enable password Cj3LF.ehxXN3xVkxWcxd encrypted
passwd Cj3LF.ehxXN3xVkWcxd encrypted
[Code] ......
View 17 Replies
View Related
Nov 14, 2011
Assuming I have the following setup: Cisco 7604 Cisco Systems Cisco 7600 4-slot Chassis System OSR-7600 Clock FRU 1 & 2WS-F6K-MSFC2A Cat6k MSFC 2A daughterboard Rev. 4.0 WS-F6K-PFC3B Policy Feature Card 3 Rev. 2.4 WS-SUP32-GE-3B 9 ports Supervisor Engine 32 8GE Rev. 4.6 WS-X6148A-GE-TX 48-port 10/100/1000 RJ45 EtherModule Rev. 4.1WS-X6548-GE-TX SFM-capable 48 port 10/100/1000mb RJ45 Rev. 11.3 The SUP32-3c says it supports both L2VPN and L2TPv3, however the line cards are effectively 6500 line cards and I was under the impression the 6500 didn't support these.
If the supervisor supports a feature does that mean it is globally supported on a switch? Or do I need to check the compatibility of these line cards as to if they support these features?
View 1 Replies
View Related
Mar 3, 2011
Trying to work out if I can setup a VLAN interface on a 1721 router.The only interfaces that are listed are the Ethernet (W1-ENET) and the Fast Ethernet interface.I'm still super new to all of this and learn how to change IOS via rommon and TFTP after realizing I had an IOS too large for the memory?
View 3 Replies
View Related
Mar 23, 2013
May I know the reason why we cannot create interface vlan on Cisco ASA 5510?
View 2 Replies
View Related
Jan 13, 2013
Whether it is possible to have same vlan on multiple interface on ASA 5510 and higher models ?
View 2 Replies
View Related
Mar 13, 2013
I have a 10Mbps connection link which I will like to reduce to 5Mbps on a 6509 switch as indicated in the config below. [code] After applying the service policy on the vlan interface, i got this "match vlan is not supported for this interface". I actually tried the rate limit command but I cant see the effect using the speedtest.
View 2 Replies
View Related
Jan 3, 2013
we've to configure our router 1841 to use both 2 interface Fe for two different vlan (also the second has to go on internet).
Actually we have int Fe0/0 configured with an ip address 192.168.1.1 for lan1 192.168.1.0/24 and we will use the second int Fe0/1 with another ip address like 192.168.2.1 for lan2 192.168.2.0/24.
see below configuration:
[code]...
View 5 Replies
View Related
Nov 10, 2011
We have a new optical fiber connection from a new ISP (only for Internet) and we found that our Cisco router RV220w won't work with this new connection because is not possible to add the V LAN ID 20 for the WAN traffic, as required by our ISP/connection. Now we would like to know what Cisco routers can support this feature and that can be "similar" to the RV220w or if there is another way to solve this problem and maintain our actual RV220w, because the features on this particular router (apart of the V LAN ID on Wan) are more than enough for us -
We would like to have a “simple” router and with firewall and VPN features as RV220w, because the one that our provider says that works seems to be too much for us Cisco 2951-SEC K9 – We are a small company with a network of around 10 computers and we only need some VPN connections for our sales companies in Europe and workers when traveling (3-5 VPN connections are OK).
View 3 Replies
View Related
May 13, 2013
we have a cissco 4506-e switch with ios version 03.02.05.SG . We ae currently facing a strange problem . Vlan interfaces configured in he switch are not showing input and output traffic, whereas the traffic is seen on the Gig interfaces mapped to the respective vlans . We also tried configuring the load-interval 30 , but there is no change . Interace 3/5 is mapped to vlan 5 . For this issue we have also done the IOS upgrade from 3.1.1SG to 3.2.5SG recently still the issue is same. [code]
View 2 Replies
View Related
Jan 29, 2012
Is it possible for me to create 2 vlan interfaces on the 6500 and have them both in the same subnet?
For a specific customer requirement I would like to have a vlan interface on the 6500 as default gateway, sat in it's own vrf, and then route all traffic inbound and outbound to this vlan through the FWSM interface, preferably in the same subnet. I don't think this will be possible so just looking for confirmation either way.
As I will be running EIGRP between a pair of central 6500's and 2 remote offices it will make things much easier for me advertise the connected FWSM interfaces in to EIGRP for access in/out of all my VRF'd subnets. If I need another subnet for each VRF FWSM next hop then I'll have to reditribute a list of statics which I don't really want to do.
The reason I am not just using the FWSM as gateway is because I need to run HSRP across 3 different devices (another 6500 in a second suite), and failover FWSM will only give me 1 level of redundancy for those gateways.
View 3 Replies
View Related
Oct 4, 2011
The is VLAN id setting in some network/LAN interface .... how can I ping this lan/network interface in XP ..any freeware can do it ???
View 1 Replies
View Related
Aug 29, 2011
I have configured a qos policy and I am trying to apply the policy to a vlan interface which is physically connected to a switch module port of a 3845 Router.When I try to apply, the message configuration failed appears.
View 4 Replies
View Related
Oct 26, 2012
I have ASA 5505 with base license. I created 3rd vlan on it.it was created. but i am unable to assign IP to it. i assign ip address it takes it. But when i do sh int ip brief it does not show any ip.
Code...
View 7 Replies
View Related
Feb 10, 2011
I have used the following basic configuration to do rate limiting on a vlan interface on a 6509:
access-list 100 permit ip any any
class-map match-all ratelimit
match access-group 100
policy-map ratelimit-10Mb
class ratelimit
police 10000000 428750 conform-action transmit exceed-action drop
[code]....
How do I combine the two correctly to give me a vlan port rate limited at 10Mb up and down, but still setting aside (dynamically) 2Mb for voice?
View 1 Replies
View Related
Aug 12, 2012
I have got a wireless project with WLC main office and have 10 sites where ap's are there and ap's getting registerd .we need 4 ssid in all branches same .
ssid guest
ssid scanner
ssid user
vlan 600 main office for scanner 192.168.1.0
in branch
vlan 600 for scanner but ip is 172.16.1.0
and bgp is running . And customer is asking me not to edit the ip range or vlan or create new vlan . but in wlc am not able to create branch network 172.16.1.0 range interface and vlan 600 as vlan 600 i already created for scanner main office 192.168.1.0 So is there a way to do that .
Temprarly one site i did like created vlan 610 in branch no ip . And in main office interface vlan 610 given another ip range . and i created interface in wlc . from branch i can connect the ssid and getting ip . But they dont want to create any aditional vlan or another network . Customer dont have a smartnet contract . They recently baught 2 wlc 5508 and 40 ap 1142.
View 4 Replies
View Related
Apr 22, 2012
we have applied route-map on vlan interface in the form:
ip access-list extended TEST
permit ip 172.16.1.128 0.0.0.127 172.16.0.0 0.0.255.255
route-map TEST permit 10
match ip address TEST
set ip next-hop 172.16.111.1
interface Vlan11
ip policy route-map TEST
The problem is in the traffic matching by the rule - there is matches not only for 172.16.0.0/16 prefixes but for the whole traffic in that VLAN.
View 1 Replies
View Related
Dec 6, 2011
Vlan interface would be dropping packets on the input queue? Refer to the drops/flushes below. This is from a 6500 with a Sup720, there are a number of vlans on it. This 6500 and it's HSRP partner are exhibiting the same symptoms on all the vlans I bothered to check. This particular vlan is quite lightly used, there are only about fifteen user PC's (each with 100 Mb interfaces) on it.
There is a bit of information on input queue drops on Cisco, but this is focused on physical interfaces where I can understand some packets being dropped. I would think that Vlan interfaces would have different issues.I note the "no buffer" errors as well, that also concerns me, especially as that counter is quite close to the "flushes".
Vlan123 is up, line protocol is up Hardware is EtherSVI, address is 00d0.04fd.6000 (bia 00d0.04fd.6000) Description: Vlan123 Internet address is 10.123.123.7/24 MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive not supported ARP type: ARPA, ARP Timeout 04:00:00
[Code] .......
View 3 Replies
View Related
May 1, 2013
I have a 3560G that I cannot apply a policy route-map to one of the VLAN interfaces. I am running up to date software, c3560-ipservicesk9-mz.150-2.SE2 and it accepts the command, but does not show it in the sh run of the interface. I updated to this code as I had seen previously someone said it needed to be version 15 before you could apply route-maps to VLAN interfaces.
View 4 Replies
View Related
Nov 20, 2011
I have a cisco router 3845 with Etherswitch modules and one Vlan configured "172.16.6/24", many switch ports are assigned to this vlan. i would like to translate one IP address 172.16.6.200 to a new one "172.25.42.10" but need to keep the other IPs from "172.16.6/24" without changes. below is the configuration of vlan interface and switch port. [code]
View 8 Replies
View Related