Cisco WAN :: No ATM Interface On 887VW?
May 28, 2012
We've purchased 3 Cisco 887VW (VDSL over PoTS) and have been advised they can be used as ADSL2+ routers
I've configured many 887 and 877 routers before for DSL, but never VDSL.
We've followed the documentation at [URL] but the problem is there is no ATM interface showing up in config, nor can one be configured controller VDSL0 operating-mode can only be set to Auto also Troubleshooting so far:
Connected to ADSL2+ line in the hope that it sees the ADSL2+ connection and creates an ATM interfaceUpgraded IOS image to c880data-universalk9-mz.152-2.T1.binUpgraded VDSL chipset firmware to 120330_1738-4.02L.03.A2pv6C035j0.d23j I was beginning to think the unit was faulty, however opening a second 887VW confirmed that there was still no ATM interface
I'm sure at this point it's that the method for configuring has changed, there is an Ethernet seperate from the switchport but I'm not sure how this would be achieved
As for the interfaces, the back of the unit has the usual 4 FastEthernet ports, a BRI interface and a VDSLoPOTS interface to connect a PSTN line
Within IOS, the router sees the following interfaces: BRI0BRI0:1BRI0:2Dialer1 (PPPoE client for DSL)Ethernet0 (Virtual interface, it doesn't exist on the back of the unit, thinking this is where the config needs to happen)FastEthernet 0-3Vlan1Wlan-GigabitEthernet0 (embedded AP)wlan-ap0 (embedded AP)
View 2 Replies
ADVERTISEMENT
May 9, 2012
i have a 1841 cisco router and i recently purchased a 1 port HWIC wan interface card. My problem is that I cannot see the interface in my config file. Is there something i am missing?
View 8 Replies
View Related
May 1, 2012
I have a Cisco ASA 5505 and I have my internal and external interfaces configured but I currently cannot ping from the inside to an IP Address on the outside. I had this setup and working and I have another set of equirement that I am replacing that is working with my service provider so I know it is a configuration issue. When I ping 4.2.2.2 for example I get:
Destination host unreachable
Do I need to add a static route from my inside interface to my outside interfaces?
: Saved
:
ASA Version 8.2(5)
!
hostname pxasa
[Code].....
View 2 Replies
View Related
Apr 9, 2011
Is it possible to set up a WAN interface on a FastEthernet interface of a Cisco 877 Adsl Router ?Due to my ISP, i've to use an external VDSL modem and must connect it to my cisco 877 router (and leave it's adsl interface unused).But i don't know how to set up a wan port, other than the adsl interface itself (dialer0), on my cisco.
View 7 Replies
View Related
May 28, 2013
We are having Cisco ASA 5540 having Cisco Adaptive Security Appliance Software Version 8.0(5)23 at certain time of moment daily wer are facing latency and packetdrop wherin when I checked for ASA Interface which gives me " Input Errors" on outside interface ,so can any one tell me what are the causes to get input errors on cisco asa outisde interface.
View 2 Replies
View Related
Feb 13, 2012
I have a 1t3/e3 card in a new 2951. When I statred the router, I found no interface corresponding to this module when do "show ip interface brief"
View 3 Replies
View Related
Oct 9, 2011
I have Pix 501 firewall and I'm just configuring the device for "Email Server" to allowing POP/SMTP.
Inside Interface Address: 132.147.162.14/255.255.0.0
Outside Interface Address: ISP provided IP address
My question is can my traffic goes from inside interface to outside interface? (because the inside interface address not from 10.0/172./192.168 private address)Also I'm allowing internet from this email server (132.147.162.14) so what my access list to be configured? and what my subnet mask shoud be there?
Pix(config)#access-list outbound permit tcp 132.147.162.14 255.255.0.0 any eq 80
Pix(config)#access-list outbound permit udp 132.147.162.14 255.255.0.0 any eq 53
Pix(config)#access-group outbound in interface inside
View 7 Replies
View Related
Mar 18, 2013
I've got a ASA 5550 firewall interface failover issue. (File attached).
when I shut down the inside interface Gi 1/1 of the left firewall(Active firewall), It failed to failover. but when I shut down the Gi 1/12 of the Core 1 switch, The firewall failover very well.
I followed this guide but I was not able to failover. [URL]
how can I configure so that when the Gi 1/1 or Gi 1/0 interface goes down, it can failover ? Code...
View 6 Replies
View Related
Apr 22, 2012
Needing to bridge from my wic interface to an ethernet interface on a 2900 series router so that I can pass through the ip address given to the WIC, to my ASA so that I don't have to give my ASA a private range address. (Just like a service provider might do when bringing a T1 with managed router in to my prem)
View 1 Replies
View Related
Oct 31, 2011
I share a modem and router with my building, and connect to the internet using an ethernet cable which plus right into the wall in my apartment. When I hover over the network/internet icon it tells me that I have a local connection only and can't get online. No changes were made to my computer between it working and not working - I have not installed any new software and the modem+router have not been changed.
When I try ipconfig/release is says it can't perform the operation while the media is disconnected. It also tells me that "an error occurred while releasing interface Loopback Pseudo-Interface 1: The system cannot find the fie specified".
[code]...
View 1 Replies
View Related
Apr 5, 2011
I have five 877 routers connected to ADSL circuits provided by Vodafone. Each has a VPN tunnel back to a PIX.
Occasionally one of the sites will lose it's connection to the PIX.
When we check the log, we find entries like these:-
Apr 5 01:31:54.085 UTC: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access2, changed state to downApr 5 01:33:19.344 UTC: %CRYPTO-
[Code].....
As you can see, the physical interface (ATM0) is not being reported as changing state to down, neither is the Dialer interface.
When the router is in this state we have to SSL to the public IP address of it and manually restart the ISAKMP SA.
When the router sees the ATM interface go down and subsequently come back up, the VPN connection to the PIX also recovers.
So - in a long winded way I think I'm asking....why does the Virtual interface go down and is there anything I can do to stop it happening?
View 3 Replies
View Related
Mar 3, 2013
what difference is between these two ports?
I have a router with ISDN/BRI interface and i am planning to buy router with E1/PRI interface. Will i be able to connect them?
View 2 Replies
View Related
Jun 13, 2012
Does the ACS Express have the same GUI interface that the full ACS appliance? I mean if I know one I know the other?
View 4 Replies
View Related
Jan 25, 2013
I've been able to activate and configure the Cisco 819 router to connect to Verizon via interface Cellular 0 but when I connect a laptop to the router, int Cell 0 goes down.
Here's a snippet of what happens after I connect a laptop:
rt1#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
[Code].....
View 0 Replies
View Related
Mar 20, 2011
I have a 5520 VPN that is otherwise correctly configured for access (so I would say). It is in test (external IP x.x.x.10/22) running parallel on an external switch to a Check Point (x.x.x.4/22) that is the live setup.
I can tunnel consistently to the outside interface on its external IP from inside the network, which is probably natural since I'm inside the network making the attempt; however...
When attempting connection from somewhere outside the network, I generally do not get response from the device. If I connect/disconnect from the Check Point VPN first, then I can subsequently get a connection to the ASA. I did actually have one instance of non-massaged connectivity to the ASA, but there was nothing that I did in the configs that would allow me to claim credit for that instance.
So here's the question: Is there a timeout setting that makes the outside interface go to sleep or something? I'm still at the developmental stage where settings that would be obvious trip me up for hours. I verified the routes. the timeout configs are below; I believe they are all default..
arp timeout 14400
!
timeout xlate 3:00:00timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolutetimeout tcp-proxy-reassembly 0:01:00
View 3 Replies
View Related
May 5, 2012
I receive email when an interface comes down but because i have a lot of routers with a lot of interfaces i can' tell which one came down , is there any way to include the description under the interface in the email ?
Also can i monitor the existence/not of specific route in the routing table and receive email ?
View 2 Replies
View Related
Feb 18, 2013
I'm having an issue setting a static NAT
We have a block of 5 public ip's
66.x.x.34-38
IP 66.x.x.38 is assigned to the outside interface. I can set static nats to all the other ip's and they work fine yet a static NAT using the same address as the outside interface does nothing.
I've used
object network centralpark-http
host 192.168.1.227
nat (inside,outside) static interface service tcp http http
View 1 Replies
View Related
May 25, 2011
*By default, the interface with higher security level can access "interfaces" with lower security level*By default , lower security level interface has no access to higher security level interface (access list needed to permit access
View 9 Replies
View Related
Feb 18, 2011
On my Switch (3750), i have a host connected. Checked the interface status and it shows as "connected". However, when i tried checking the MAC connected to that interface, its not showingI have my Switch (3750) connected to a Router (3845). On the Switch, i have a printer connected in an interface. I am seeing the Printer's MAC associated with the switch port. However, when i checked the ARP table; no entry seen for the Printer's MAC. What are the possible reasons for this? We have several same kind of devices connected to network and they are fine.
View 5 Replies
View Related
Nov 5, 2012
I'm trying to separate my management traffic from regular traffic by splitting the management and "outside" interface to separate vlans but I'm hitting a routing issue. Say I have have a management network of 192.168.1.0 255.255.255.0 running across vlan 1 and I want to use 192.168.2.0 255.255.255.0 running across vlan 2 for the outside interface to send all the other traffic excluding the management traffic across. Tag both vlans on the external interface, say Eth0/0 Default route of route outside 0.0.0.0 0.0.0.0 192.168.2.1, With this, you can not hit the management interface because there is no route defined for the 192.168.1.0 network. However of course if you try to set one, you'll get the "connected route exists" error. How can I set the default route or gateway of the 192.168.1.0 network on the ASA. Switches just don't complain like the ASA does.
View 8 Replies
View Related
Apr 25, 2013
I followed a few Youtube videos and replicated another ASA's VPN configuration through ASDM to create the Anyconnect VPN on the ASA 5505.The problem is, after everything checked and triple checked, I still cannot get to https://external_IP. I can post configs if needed, but I really did replicate another ASA almost exactly.An online port scan shows my external IP as "not listening on port 443".
View 6 Replies
View Related
Dec 21, 2012
I have E1 interface that supports 2Mbps and i need to connect Point to Point , my question is can i add 2 more E1 interface on my cisco router and configure it using channels on that link so i can increase my bandwidth up to 6Mbps.
View 5 Replies
View Related
Feb 20, 2013
I am trying to do a Multicast lab in gns3 with a tap interface in os x and a linux vm in virtualbox. The os x box is broadcasting to 224.1.1.1. I have verified IP connectivity. I am using PIM dense mode. When I perform a packet capture on the tap interface I see no traffic to 224.1.1.1. However when I ping 224.1.1.1 from os x I see the traffic. Attached is my topology
View 1 Replies
View Related
May 23, 2012
We have a lot of 6913's handling our office ports and I'd like to know a simple way to find multiple ports knowing their description.
I'm use to Juniper so if I were looking for the 8 ports for the office's 3190-3199 I would type something similar to:
show | display set | match 319
I know I can use | include with a show run on Cisco but that won't pull the interface just the description.
View 11 Replies
View Related
Dec 12, 2012
Could you explain me what "interface ATM0" is ? Is it virtual interface or physical ? And in this configuration ATM stands for Asynchronous Transfer Mode or anything else?
View 11 Replies
View Related
May 16, 2011
I need to configure one interface in failover because the client has 2 ISP.[CODE]
View 2 Replies
View Related
Sep 2, 2012
I have Cisco 3845 with two Gigabit interfaces configured as port-channel with sub interface and with QoS. However shape does not work.
[code]...
View 8 Replies
View Related
Sep 1, 2011
Is-it possible to manage Cisco phone by web interface? (Manage transfertdiversion... of IP phone)When i go to http://ip_cisco7961 and i give permissions in settings of user (web Access: Enabled)I have only information in read only.
View 4 Replies
View Related
Mar 14, 2012
According to Cisco's site the WS-X6748-GE-TX is a "10/100/1000" module.URL
View 7 Replies
View Related
Jul 5, 2011
Right out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies
View Related
Jul 15, 2012
I have a dual connection from two service providers ( provider A & Provider B).In my internal network, I have two Vlans (vlan10 & vlan 20).My requirement is users belonging to vlan10 should go via ISP A and for vlan 20, it should go via ISP B.So, for that purpose, I configured HSRP along with intervlan routing and that worked quite fine. I have two Cisco AS5300 routing connecting to both ISPs and they are terminated to a common switch Cisco2950.All are in ethernet technology, serial technology has not been used. "IP SLA" command is not supported in CiscoAS5300.I configured the interface tracking command for HSRP as well.
When one link goes down then it doesn't fail over and go through another link. To fail over, I should manually remove the external link connecting to the router. And another thing is, if i pulled the cable connecting to the internal network then it fails over. "IP SLA" command is not supported in CiscoAS5300.I am trying to implement a failover using HSRP in Cisco AS5300 but the interface tracking is not decreasing the priority value when the connection is lost with the ISP and IP SLA is also not supported. So, in this case what can i do to make a perfect failover for the network ?
View 4 Replies
View Related
Jan 21, 2013
I configured a Cisco 881 as a vpn-client.When I configure the wan-interface with ip add dhcp , it never gets an IP-address.When I remove the crypto map from the wan-interface , the interface gets an IP-address without any problem.According to examples in the Cisco documentation, I should work; and it works on a 831.
View 3 Replies
View Related
Jul 21, 2011
We have a 3845 router, IPBaseM, ver 12.4(15) that seems to accept an SFP (GLC-LH-SM). It does not show up on a show run, or Sh Ip int brief. If I type show tech-support | include sfp, it returns "sfp_transciever_cod 0x2 (1000BaseLX)".How do I go about configuring it for Ethernet Private Line access?
View 1 Replies
View Related
