Cisco WAN :: PPPoE Termination On 1921?
Apr 18, 2012
I have cisco router model 1921 , how can i terminate my existing pppoe connection to 1921, so that my other LAN users can use internet.
1- One cable (RJ45) which is comming from ONT has connected with Integrated WAN Port on router.
2- One cable (RJ45) which going to my LAN switch has connected with Integrated LAN Port on router.
Now i need to configure my router, so that i can give internet access to my LAN users. I red cisco's guides but not clear regarding configurations, because in guides they use modules to configure pppoe. But i am not using any module, i am simply connecting one cable for WAN and one for LAN.
View 1 Replies
ADVERTISEMENT
Oct 15, 2012
I am attempting to bring up a remote router using a pppoe connection by replacing the current Tenda 308R router with a Cisco 1921 using the Ethernet connection on the WAN side. The connection works fine with the Tenda in place but when I put the Cisco in I get no connection and no answer for my PADI queries.I always get padi timer expired. I do not think it is even getting to the ppp authentication. [code]
View 5 Replies
View Related
Oct 5, 2012
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
View 4 Replies
View Related
Nov 9, 2011
Our HQ Location dont support high bandwidth pipe served by ISP, so will go ahead with 3 different ISP at 2MB each.Goal is to provide Email / Application access to Remote office using site to site VPN.In Total will have 10 to 15 Branch offices each with around 25 to 35 users
Each ISP will give
/29 subnet of public IPCopper Interface for WANdefault Gateway and Two DNS server IP will be provide Existing hardware we got are Cisco 2821 Router with 2 FastEthernet ports ( not in use )24 port switch 2900 series ( not in use ) Can we use the above hardware to terminate all 3 ISP link and use the Router for site to site VPN.
Our Lan Core is Cisco 3560 which is uplink to 3X2950 user switch?how should we terminate the link and use each ISP for VPN.
View 3 Replies
View Related
Nov 13, 2012
we configued An ACE 4710 with SSL termination on Oracle Aplication Server 10g (10.1.2.0.2) ,so that SSL termination is done on the ACE and HTTP reaches the Oracle Aplication Server 10g (10.1.2.0.2) then we configure the ACE to enabled client authentication with Pkcs#11 smart card token certificate and this don succfully my problem need do this client certificate authentication for only the [URL] not for all SSL proxy service how can do that.
View 3 Replies
View Related
Jun 17, 2011
I read in the Cisco IOS ASA documentation (8.x) that some group-policy attribues are only available for soft-VPN clients while some are available for both soft-VPN clients and L2L VPN clients. Cisco didn't clearly specify which attributes were available for which clients.
To aid me in troubleshooting my L2L VPN setup could someone indicate if the order of events (listed below) is correct for ASA 5520 with IOS 8.x and if the attributes selected are available for L2L VPN clients?Also, are there "show" commands to reveal more details about tunnel-groups, group-policy, etc. when used with VPNs?
View 1 Replies
View Related
Feb 21, 2011
We are going to purchase a Device , thte sites and also VPN server for remote access ( EzVPN), Should we use ASA or should we use Cisco 1800 series router with security software. The main purpose of this device is to terminate all VPN connections ( Site-to-site) and remote access.
View 1 Replies
View Related
Sep 17, 2008
We are evaluating the one-arm design for the ACE 4700 and need some clarifications:
1. Are there any limitations in the one-arm design and the SSL offloading
2. Can the ACE be configured with an IN and an OUT vlan to the router
CLIENT -> Router -> ACE IN -> ACE OUT -> Router -> Server Vlan
so that the SSL and the clear text traffic is in a separate Vlan?
3. In some sample configuration i saw SNAT configuration on the ACE to modify the client IP. This i assume is for instructing the return traffic from the server to go through ACE? Using SNAT we eliminate the requirement for NAT or PBR on the router? Will i still be able to insert the client IP address after the SSL offload?
View 4 Replies
View Related
May 7, 2012
I am terminating GRE vrf-lite on my 7600 and using loopback as source for each client.I found one problem where 7600 seems to be not forwarding traffic until I delete create the tunnel interface.Worked fine for a week. Then stopped again. I had to delete,create again tunnel interface.
View 6 Replies
View Related
Apr 17, 2011
I am setting up a new ASA 5510 on our inside network so that we can terminate our VPN connections on this ASA. I can get the VPN to work fine however I noticed that once I turned on my VPN profiles now when I try to access the ASDM I'm getting the VPN logon page. So I decided that in order to resolve this I need a separate interface dedicated to management of my ASA.
I'm trying to come up with the best way to do this. I've got two ports on the ASA plugged into my core switch. One is on a separate VLAN from the rest of my network traffic. This is the port I want to use for management. The second will be used to route all of my VPN traffic.
So far I haven't been able to get this to work at all. My thought was that it had to do with routes, NAT and ACLs. I've been playing with them but can't get any combination to work.
View 2 Replies
View Related
Sep 10, 2012
Cisco SRP527W-U.
We would like to configure it in the following way, 1) we have an ethernet termination for the WAN 2) we have 2 different vlans going to 2 different switches.
Can we have the default gateway for 2 LAN subnets and a default route via a /30 for our WAN. Can we use the 4 switchports for this?
switchport 1 VLAN 2 (Switch 1 LAN)
switchport 2 VLAN 3 (Switch 2 LAN)
switchport 3 VLAN 4 (Link to Data centre switch with /30)
View 2 Replies
View Related
Nov 2, 2011
We have an ASA 5510 with ~100 vpn lan2lan. Now we need to migrate to a new ISP, so we have connected a new asa interface to the internet. Default gw is still on old connection. We are trying to migrate vpn lan2lan using static routes, pointing ip of remote vpn gateway to new isp gateway. VPNs going up, but when they try to send traffic, I can see Rx counter growing up, but Tx remains 0.. I've tried with different vpn (old and completely new), and problem remains.
View 1 Replies
View Related
Oct 23, 2012
Im trying to configure an ACE 4700 so that SSL termination is done on the ACE and HTTP reaches the weblogic server instance. I have a working setup of a Apache reverse proxy doing SSL offloading and using a weblogic module and that works fine Was reading [URL]. Any working config example for doing this with the ACE4700
View 2 Replies
View Related
Jan 2, 2012
I am doing an small project, I have to connect 4 cisco switches SF 302-08 (1 GBIC each one) to a core switch SGE 2000 (4 GBICs). Because of cable length I have go connect all 5 switches with fiber. The fiber termination is multimode LC duplex. My confusion is on the mini GBICs. There is compatibilities issues i been reading. [code]
View 3 Replies
View Related
Feb 11, 2007
The "Wireless Network Monitor" for my Linksys Dual-Band Wireless A+G Notebook Adapter Model No WPC55AG has been unable to run after I last updated my Windows XP machine using Windows Update. The problem presents itself immediately upon login (because the monitor is set to run on startup) with an error window that says "Abnormal program termination" and "WPC55AGV2.exe" in the title bar. I suspect the problem occurred because one of the new updates included an upgrade to the Microsoft .NET Framework Services 3.0.
View 6 Replies
View Related
Oct 3, 2011
I have a Cisco 877 doing PPPoE through a ISP supplied modem that is in bridge mode (long story). When the DSL drops on the modem it takes around 5 to 10 mins for the 877 to redial the connection.
Here is the config I'm running:
interface Vlan1
description PPPoE-Interface(WAN)
ip address dhcp
load-interval 30
pppoe enable group global
pppoe-client dial-pool-number 1
[code]....
Its possible some of that config is redundant but I've tried as much as I can see online.
View 6 Replies
View Related
Dec 16, 2011
Cisco 877W. I configured it for PPPoE. But once I plug in the ADSL line, the dialer interface will get IP Address. But after like 2 minutes the PPP link will go off and I will get this log message: "Interface Vi1 unbound from profile Di1".
View 2 Replies
View Related
Mar 2, 2011
Is it possible to set up a pppoe client on a VLAN interface, or a switch interface associated to an VLAN?. For example, in a 881 ethernet router, could I configure a pppoe client on any of the lan interfaces in addition to the pppoe client configured on the WAN interface?.
View 4 Replies
View Related
Aug 29, 2011
Trying to find a way to configure my 851 for home use. My internet provider use PPPoE with PAP and althrough I found many configuration options they all are incomplete...or i cant find the logic behind those commands. First of all I need to say what I need:
1. Configurate my int Fa4 (WAN) with pppoe so when i insert my ISP cable in it it will negotiate and take IP.
2. Configurate DHCP on LAN (Fa0-3) so that when I insert my PC it will take a fake IP.
Here is the place where i found some conf examples: [URL] and I have some questions:
1. MTU - Should I use the 1492 value or the "pppoe-client ppp-max-payload 1500"?
2. ip route 10.10.25.2 255.255.255.255 dialer 0 - How can i set an IP route when my connexion informations only come after i connect? (Because is PPPoE)?
3. I cant configurate the DHCP because I dont know the default route, I dont know the DNS, and i dont know the default gateway because I dont know them due to PPPoE !
View 20 Replies
View Related
Apr 27, 2011
I am using ASA 5505 with firmware 8.2(2). My ISP uses PPPoE as a WAN connection protocol. There is a problem with getting PPPoE session started on my ASA 5505. The debug output says that after negotiation of PPP-authentication protocol ASA receives a PADT packet from ISP’s concentrator. To get more information I captured all packets on outside interface with WireShark. Packet-dumps (in .pcap format) are attached in this post. I have tried all possible combinations of PAP/CHAP/MSCHAP values in “vpdn group MYGROUP ppp authentication” command. If you take a look at the packet-dumps you can see, that in case of “PAP” – ISP’s concentrator rejects negotiation (PAP is not supported by my ISP). In case of CHAP/MSCHAP (that ARE supported by my ISP) – ASA acknowledges the using of MSCHAP v.2 PPP-auth protocol, which is actually not supported by it…
Judging by MAC-addresses of ISP’s concentrators it is visible that Cisco’s equipment also is used.
The questions is: Why ASA acknowledges using of unsupported ppp-auth protocol during negotiation and what I need to do to resolve this issue? (ISP’s support says, that they cannot change PPP-auth protocol negotiation order. Also they says that I need to contact with manufacturer of my equipment).
View 3 Replies
View Related
Jun 19, 2012
PPPoE is established and I can access router from outside. But router can't ping itself and ouside and NAT isn't working as well. Main goal is to make Internet work from router.
Cisco IOS Software, C890 Software (C890-UNIVERSALK9-M), Version 15.0(1)M7, RELEASE SOFTWARE (fc2)
version 15.0
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
[Code].....
View 2 Replies
View Related
Feb 19, 2011
is it possible to configure a Cisco 878 Router to act as a device(router) between a DSL Modem and the LAN ?
There is the following scenarium: "Deutsche Telekom DSL Modem -> Cisco Router 878 -> LAN"
DSL is an SDSL Connection with a static IP address.
View 1 Replies
View Related
Mar 19, 2012
I have recently gotten a cisco 1941 router running version 15.1(3)T, and am trying to configure the router as a PPPoE server for access via a vlan on one of the gigabit ethernet ports.I currently have a cisco 2620 router (version 11.3(2)XA4) with the following relevant configurations:
vpdn enable
vpdn multihop
vpdn domain-delimiter @ suffix
!
vpdn-group pppoe
[code]....
I am trying to duplicate this (all but IP addresses) on the new router, but there are some options that do not seem to exist in this particular software/hardware combination. Specifically,
vpdn-group pppoe
accept-dialin
protocol pppoe
does not accept "pppoe" as a protocol, only allowing l2tp. What has changed, and what the proper configuration is.
View 1 Replies
View Related
Jun 20, 2012
I'm trying to get a PPPoE config working on an 1841. Running c1841-advsecurityk9-mz.124-3i.bin . I tried c1841-advsecurityk9-mz.151-4.M4.bin but it has even less protocol options.
I used a walkthrough but it suggests the following fragment which doesn't work because there is no "protocol ppoe" command available on my system. Perhaps there is a simpler way to do this? I tried c1841-broadband-mz.151-4.M4.bin but it doesn't seem to have ssh available.
vpdn enable
vpdn-group 1
request-dialin
protocol pppoe
exit
[Code]...
View 3 Replies
View Related
Oct 27, 2011
We are a small business that just bought a Cisco 1921 ISR. I am trying to set it up right now but I cannot get CCP to discover it. I am new to Cisco products and IOS.The router is currently set up in a test environment with a USB connection to a Win7 PC for console management. I also have the PC connected to gigabit ethernet port 0/1. I am using putty to access the console which I did with no problem for the initial configuration. After that I thought I would be okay to discover the router with CCP using the IP address I specified but then it prompted me for a username/password which I didn't see in the initial configuration. After this I did some research and found out I needed to set up a few more things so I ran the following commands: [code]
After this the video I was watching said to go in to CCP and specify the IP address or hostname of the router and use the login info that was just created admin/pw. When I ran the discovery I got the failure message: Connection to the device could not be established. Either the device is not eachable or the HTTP service is not enabled.When I run 'show ip interface' I notice 'Router Discovery disabled" is this why it is not working? How can I enable this or what else am I missing here? Am I not connecting to the router correctly? Oh and just for reference our plan is to have this router set up as a VPN gateway and firewall with 2 WANs for redundancy and connecting to our switch via an HWIC SFP for fiber.
View 14 Replies
View Related
May 18, 2011
I have installed a Cisco 1921 router in our company and i have stumbled upon an issue with the DNS.
We have a internal DNS server and an internal WEB server. In the DNS server there are records pointing to sites on the WEB server, this is working just fine.
The thing is when i use a public DNS such as 8.8.8.8 (googles public DNS) i cannot resolv the external IP of those sites. I do not want to access the sites and i do not want to send any packets to the sites. All i want is to query the public DNS and resolv the public IP where the site is.
View 1 Replies
View Related
Sep 25, 2011
I have a ZyXel P-660R-D1 DSL modem, and lately I've been experiencing random outages. I'm not super knowledgeable when it comes to the technical side of networking, but I know enough to look around the modems GUI and recognize when something isn't right. I'm pretty sure this is not a problem on my end, but I'd like to hear a few other peoples opinions. Basically I have four lights on the modem: Power, Ethernet, DSL, and Internet. DSL is the light that indicates connection to the PPPoE server, and lately it will just randomly drop. I've never experienced problems connecting with the PPPoE server until just recently. Every once in a while my Internet light will drop, and a simple reset will take care of it, but rarely am I ever not connected to the PPPoE server. One day it was down for three or so hours, one day for nine, another day it cut in and out for about four hours, and today was another nine hour day. how it works is that my username and password are verified through the ISPs PPPoE server, and then I am granted access to the web. I'm lead to believe that it's nothing on my end because all troubleshooting methods fail, it just randomly fixes itself several hours later. The first nine hour stretch I experienced I thought may have been because of maintenance or some other unforeseen circumstance, but it has happened a few times now so I'm not too sure. My provider, Earthlink, hasn't listed any 'Known Outages' on their site, but then again they never do.
View 1 Replies
View Related
Nov 27, 2011
Two days ago our desktop computer stop having internet access. I called my ISP about this problem and they said that everything was fine with my router and that it might be a bad cable. I bought a new cable and it wasn't the cable. I called my dad's friend who works with computers and he said that he thought the NIC was bad. So we went to Staples and bought a Gigabit Ethernet PCI Adaptor, because that would fix the problem, well i installed all of the software and it didn't and we're stumped on what to do.
Our laptop still gets wifi however when I try to connect on my desktop it says that it can't connect through the WAN miniport PPPOE. It gives me error 815
View 4 Replies
View Related
Jan 2, 2013
I just switched to DSL from cable internet and am having some trouble setting up my router with the new internet service. DSL modem-->Router-->Network with PC and PS3
ISP is ATT
DSL modem is a TP-Link 8616
Router is a D-Link DIR-628
I put my ATT username and password into the router but it never completes a connection to the internet. I was able to create a soft PPPoE gateway connection through my computer using my username and password, but I want my router to do this, not my PC. How do I get my router to connect directly to the Internet connection rather than having my PC connect? My setup would be fine as-is if I just had 1 computer but I also want to go online with my PS3, and it won't connect like my PC will, even after putting the username/password in.
View 11 Replies
View Related
Jan 7, 2011
A PC connected to a Cisco 877 router and 877 router is connected to another router (7301) via GRE tunnel,Cisco 7301 router is a NAS server and is being used as a PPPOE server.If user create a PPPOE connection on his computer and dial with a username/pass we want to send the PPPOE traffic to 7301 router, so 877 router should pass the PPPOE traffic to 7301 and user will be able to connect,User -> 877 -> 7301(PPPOE server).
View 4 Replies
View Related
May 13, 2013
I get stuck in one case. One of my customer has two FTTH lines. I have to config PPPoE in routers. In one line I config succesfully, but one line never up. I call to ISP they ask me to config extactly VLAN id 10 in the physical subinterface. But in subinterface there is no command "pppoe-client dial-pool-number". I check the old modem FTTH, they also config VLAN 10 in Wan interface. I tell ISP why we have the same two FTTHs, but two differrent config ways. ISP says because the two line run in two different infrastructure, two different devices. I don't know how to do now? stay in customer side or ISP side. Here is my PPPoE config:
interface FastEthernet0/0
no ip address
duplex auto
[Code].....
View 4 Replies
View Related
Dec 5, 2010
The pppoe on IOS (15 version) does not work (when using 12.4 version- everything is OK)I have tried it with c880data-universalk9-mz.151-1.T.bin, c880 data-universalk9-mz.150-1.M3.bin, c880data-universalk9-mz.150-1.M2.bin - DOES NOT WORK.But it DOES WORK with c880data-universalk9-mz.124-24.T4.bin.The configuration interface FastEthernet4 no ip address duplex auto speed auto pppoe enable pppoe-client dial-pool-number 1 service-name "xxx" interface Dialer0 ip address negotiated ip mtu 1452 encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap callin ppp chap hostname xxx ppp chap password 7 xxx.
View 10 Replies
View Related
Jan 1, 2013
I'm trying to configure an Cisco 1841 with IOS 12.4 to an FTTH conection.I would configure PPOE protocol in the vpdn-group 1 but I can't see this option in the command line,I have read about the command "bba-group pppoe global" but i'm not sure if it has the same result. It's valid? How can I use the bba-group pppoe global¿? I need to use it with a virtual template?
View 9 Replies
View Related
