Cisco WAN :: 1921 Remote Router Using A PPPoE Connection By Replacing Current Tenda 308R
Oct 15, 2012
I am attempting to bring up a remote router using a pppoe connection by replacing the current Tenda 308R router with a Cisco 1921 using the Ethernet connection on the WAN side. The connection works fine with the Tenda in place but when I put the Cisco in I get no connection and no answer for my PADI queries.I always get padi timer expired. I do not think it is even getting to the ppp authentication. [code]
View 5 Replies
ADVERTISEMENT
Jan 18, 2013
I have a Cisco 1921 to replace our current router which is constantly freezing. We have a couple inside servers, one is a web server and application server which needs to be RDP'd to by a couple of clients outside of our network. I cannot get this to work no matter what. I know it's not the server's setup as when I plug the network back into the old router, it works just fine.
All clients have access to the internet, and I can successfully ping/resolve hosts from both the router and a client computer connected. I cannot, however, rdp using neither our public IP, nor our hostname. The hostname does resolve to our ISP assigned IP, but the server cannot be contacted, leading me to belive this is a NAT issue. [code]
View 2 Replies
View Related
Oct 26, 2012
I would like to use a Cisco 1921 at my house and create a "Easy VPN Remote" connection to our ASA 5510 at work. Can I use the Easy VPN Client with the base license, or do I need the security license to take advantage of the VPN tunnel?
View 4 Replies
View Related
Apr 18, 2012
I have cisco router model 1921 , how can i terminate my existing pppoe connection to 1921, so that my other LAN users can use internet.
1- One cable (RJ45) which is comming from ONT has connected with Integrated WAN Port on router.
2- One cable (RJ45) which going to my LAN switch has connected with Integrated LAN Port on router.
Now i need to configure my router, so that i can give internet access to my LAN users. I red cisco's guides but not clear regarding configurations, because in guides they use modules to configure pppoe. But i am not using any module, i am simply connecting one cable for WAN and one for LAN.
View 1 Replies
View Related
Dec 15, 2011
I have to open several ports from the WAN to LAN on a 1921:
For example:
Say I need port 41795 both UDP and TCP to go from the WAN to the LAN, can some provide me the context I have to follow?
Currently I have this in place
Another piece of this is that the devices that will need to be accessed remotely are on VLAN10 - will that cause a problem?
is installed at a clients home for a very complex Crestron network that included 5 Cisco POE GB switches, 2 VLANS, with VLAN10 utilizing QOS and is the AV network (VLAN1 is the computer network), 8 1142 WAP's, and this 1921.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.12.16 19:52:41 =~=~=~=~=~=~=~=~=~=~=~=show runBuilding configuration...
Current configuration : 3340 bytes!! No configuration change since last restartversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname DHOWE_Router!boot-start-markerboot-end-marker!!enable secret 5 $1$JuTn$zn6CnXIm1bJGgPhtRCfB0.enable password ********!no aaa new-model!!no ipv6 cefip source-routeip cef!!ip dhcp excluded-address 192.168.39.0 192.168.39.49ip
[Code] ........
View 3 Replies
View Related
May 3, 2011
I am using a PPPoE connection on a linksys WRT54G router and trying to set up an Edimax EW-7206APg to extend my wireless connection range.I followed the instructions given on the Edimax manual, but that seems to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connectionMy router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest. What am I doing wrong?
View 2 Replies
View Related
May 3, 2011
I am using a PPPoE connection using a linksys WRT54G router (working perfectly) and am now trying to set up an Edimax EW-7206APg to extend my wireless connection range. I followed the instructions given on the Edimax manual, and while my devices (iPad, laptop) got connected to the new repeater network, I could not access the Internet from it. I may be wrong, but the instructions on the Edimax manual seemed to be for a DHCP connection. Is there anything different I need to do to configure the Edimax repeater on a PPPoE connection?My router IP ("Local IP address") shows 10.10.0.1 instead of the "192.168.1.1" that all the documentation online seems to suggest.
View 6 Replies
View Related
Mar 31, 2013
Region : Others
Model : TL-WR740N
Hardware Version : V4
Firmware Version : 3.12.11 Build 120320 Rel.51047n
ISP : Blic.net (Banja Luka, Bosnia)
I'm having issues with PPPoE connection. On a daily level, my connection breaks 1-5 times. In the past, it was related to signal problems, but ISP Tech. team fixed this some 10 days ago. Now, whenever I call them they say connection was broken on user request and ask me if I'm running services like torrents.
I don't run torrents and all I have is standard windows update services, nod 32, as well as steam client.
Here's router log from today when last error occured (I "blanked" some user-specific data like my username or MAC address).
773/31/2013 17:04PPPINFOrcvd [proto=0x8057] xxxxxxxxxxxxxxxxxxxxxxxx
783/31/2013 17:04PPPINFOsent [LCP ProtRej]
793/31/2013 17:04PPPWARNINGPPPoE link down
[Code].....
View 3 Replies
View Related
Nov 29, 2012
I recently buyed a Linksys EA6500 wireless router. I accessed [URL] to access the settings interface of the router. Went to "Connectivity Internet Settings" and chose type of the internet connection as PPPoE. Entered the username and password, clicked ok.
No internet access.
View 9 Replies
View Related
Mar 6, 2012
I want to share PC internet (PPPOE connection) on my linksys wireless router (E3000)Problem : When i directly connect internet wire in router, pppoe connection frequently gets disconnected. So what i wanted was to share my pc internet on router.I have two lan card on windows 7 installed PC, 1st lan card is connected to internet cable and i can access internet on pc, second lancard is connected to wireless router. So basically what i want is to share pc internet ( PPPOE ) on wireless router through DHCP connection type.
View 1 Replies
View Related
Mar 8, 2013
I have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
View 5 Replies
View Related
Jan 17, 2013
Used an E4200 version 1 to terminate PPPoE on a really high speed connection? By that I'm talking say 400Mb or higher.
View 9 Replies
View Related
Jan 21, 2013
I haven't been able to connect to the internet and every time i trouble shoot it gives me the following report "there-problem-driver-local-area-connection-adapter" what do i do
View 1 Replies
View Related
Jan 17, 2012
I'm having a very difficult time getting my WRT54GS to work with my Westell 6100 modem. I've been bouncing around gathering info, and what I've learned is that the goofy way CenturyLink tech support told me to hook up my old wired router (modem line into outgoing (LAN) router port) is because the Westell 6100 is a "smart modem/router". Therefore, when I run the Linksys setup CD, it sees the modem as a router, and won't properly configure. I've also learned that the Westell modem can be "dumbed down" into simply a modem by putting it into "bridge mode", which is where I'm at right now - trying to get it reset to factory defaults and resetting the connection type from PPPoE to Bridge. In the meantime, I also reset the WRT54GS to factory defaults, and now I've got another problem: the router will not allow me to set up encryption. The default setting is "Disabled", and when I click the down arrow and try to make any selection at all (preferred selection is WPA2 Personal), it reverts to Disabled. I've also tried to change the router's IP address to 192.168.2.1 (and alternately to 192.168.1.253), so it won't conflict with the modem's IP, and it freezes up every time I try.
View 2 Replies
View Related
May 21, 2012
I cannot connect wan using tenda router, lan connection works.
View 1 Replies
View Related
Feb 18, 2012
How can i apply password on tenda router?
View 1 Replies
View Related
Sep 29, 2011
Iv got tenda router that is connected to the internit but it cannot recognize the othe wan devise type livel one which is connected throgh wire to the wan router?
View 1 Replies
View Related
Dec 30, 2012
I got a new Tenda W311R+ Wireless-N Broadband Router yesterday. I already have a wired broadband internet connection in my home with a Beetel 110TC1 modem. I did following:
1. Connected the Beetel modem to the Tenda router using an Ethernet cable
2. Connected the Tenda router to my PC using another Ethernet cable.
3. Went to 192.168.0.1 (as mentioned in the instructions sheet which came along with the router)
Now, what should I set as the access mode, ADSL Dial-up or DHCP? Are there any other settings I should change in order to enhance the speed? I have Windows XP SP3. Also, do I need my Beetel modem or can I use the router without it?
View 5 Replies
View Related
Oct 8, 2012
I bought this Tenda wifi router and connected it.It's a chinese one and the user interface is not much friendly. It works fine but sometimes if u play around with it u will lose the settings you inserted in to it and you will need to reconfigure it.
My problem is my ISP seems to renew the IP's issued to their customers automatically every 10 hrs from the last login. But every other router keeps the connection alive but my router doesn't. It needs to be restarted in order to get the internet back online.simply said,u need to restart the router every 10 hrs.
BTW Never buy Tenda routers.
View 3 Replies
View Related
Oct 27, 2012
how to disable firewall on w302r tenda router?
View 8 Replies
View Related
Dec 29, 2012
Tenda router w311r forgot password
View 3 Replies
View Related
Aug 29, 2011
need to disable firewall settings router Tenda D840R
View 2 Replies
View Related
Oct 12, 2011
i have tenda ADSL router using the internet of Nepal Telecom, Nepal and distributed to two users. now i want to limit the speed of the other user to least and i want to achive maximum speed of the subscription but have no idea to manage it
View 1 Replies
View Related
Nov 3, 2012
i have lost my code from the tenda wifi router modem which we can use to put security.without it how to secure wifi?
View 1 Replies
View Related
Dec 12, 2012
How do i have reset my trenda router without a disk?
View 3 Replies
View Related
Aug 20, 2011
can i set up my W311R+ tenda wireless router without the software driver?
View 1 Replies
View Related
May 8, 2012
how do i reset my password for y tenda wireless router w311r
View 1 Replies
View Related
Feb 8, 2013
I used to use a DSL modem/router supplied by Bell (my ISP) and it was a 2wire router, but the signal was not enough to supply my entire house, it was 802.11b/g.Now recently I bought a Tenda W307R, N router all-in-one with an AP.I just plugged it right into the 2wire (modem) and now the Tenda routes the wireless signal. However, I am experiencing that it slows down every few minutes or so, for 30 second intervals, then the internet catches on again and everything is good.
View 2 Replies
View Related
Feb 8, 2013
i have wimax usb modem and tenda wifi router with rj45 ports.
View 5 Replies
View Related
Jul 13, 2011
I am trying to set up a Tenda 150mbps wireless Ap/Router.Im trying to set it up to use it as a range extender.I followed all the directions. I put it in wisp mode. It doesnt seem to be communicating with my Tenda wireless router. It only is showing up as its own connection. so I cant even get on the internet.
View 1 Replies
View Related
Oct 5, 2012
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
View 4 Replies
View Related
Aug 19, 2011
I want to share the PPPOE internet connection between my Desktop and Laptop. The desktop has WIN7 and laptop has Win Vista. the desktop is having 2 LAN Cards.
View 1 Replies
View Related
Mar 27, 2012
I'm trying to configure an 887VA for a pppoe ADSL2+ connection with no luck.I know the ISP requires pppoe (LLC), and the pvc is 8/35.
The CD light is on, and the line is up, but the 887 just won't connect
View 3 Replies
View Related
