We just moved to a new place and ISP here have a bit weried connection - they use cable modem that provides "local" IP (through DHCP) to the router and than you have to dial out L2TP to the ISP in order to connect to internet.This setup works fine with "home" routers, like the LinkSys, however I have no clue on how to setup it on 2811.
View 1 Replies
I am a total new comer for Cisco Router. All I know is plug the console cable to a serial port on a PC, fire-up HyperTerminal to view and that's it. I don't know any command or scripts.
I am trying to setup my client connection, I already receive the required configuration settings from ISP. It is a Leased Line Serial connection.
How to setup the router with the below configuration.
Serial IP : 1.X.XX.222
Serial Netmask : 255.255.255.XXX
LAN IP : 1.X.XXX.1 to 1.X.XXX.31
LAN Netmask : 255.255.255.XXX
[Code] ....
I have my router connected to my ISP, but for some reason I am getting really slow internet connection compared to a home Linksys router. I can only think it may be to the fact my port is set to auto speed and auto duplex.
Sometime the websites are fast, other times slow. Cannot seem to pinpoint the reason since my code is so basic.
I am attempting to setup remote VPN access for clients but have been unable to connect remotely using Cisco VPN client. Here is the current configuration on the router. I think I'm almost there and may be missing a couple commands.
Current configuration : 4758 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname FCC-1811-Router
[code].....
setting up IPsec for a DMVPN between a 2811 and 2951s in a test lab. I have enabled IPsec on the hub (2811) but I am unable to do so on either of the 2951s. After researching, it seems that I may have the incorrect IOS for this, but I am at a loss which IOS I should be using. Currently the 2951s are on "c2951-universalk9-mz.SPA.151-2.T2.bin" and the only crypto options are(config)#crypto ?
ca Certification authority
key Long term key operations
pki Public Key components
while on the 2811 I get:
WIN-T(config)#crypto ?
ca Certification authority
call Configure Crypto Call Admission Control
ctcp Configure cTCP encapsulation
dynamic-map Specify a dynamic crypto map template
engine Enter a crypto engine configurable menu
gdoi Configure GDOI policy
[code]...
These are all hand me downs?
Configured a D-Link DIR-601 router? The internet is connected, but there is a yellow triangle with a exclamation mark on the bottom right corner stating it isn't connected. I read the manual and did everything as listed, but still have the same issue.
View 4 Replies View RelatedWe're starting to share video across our network and would like to setup multicast to conserve at least some of the bandwidth. We have a broad mix of equipment (A Catalyst 6509-E at the core, a combination for Cisco 2691 & 2811 routers, and a whole lot of Catalyst 3500, 3550, 3560 switches at a hundred locations. Where would I begin? Would I need to define routing for the multicast IP addresses (224.0.0.0)? Would I need to setup interfaces & IP networks where each multicast device is located like I would for a new IP subnet?
View 1 Replies View RelatedI had so much old garbage and damage from old viruses I needed to reformat the hard drive and reinstall windows xp from the System OS disk. Computer is up and running now, but I lost a lot of stuff, including my ability to connect to the internet and some drivers. I have cable internet. I downloaded Broadcom advanced control suite and the netxtreme 57xx drivers from the Broadcom site, and installed them with the provided download manager. Nothing seems to be working, the control suite says "No active broadcom network adapters detected in this system"....
note- I've been downloading to a different computer and burning the files to CD, and transferring them to the Dell that way...
Just moved into apartment in Ann Arbor and am forced to use this ISP. They are not wireless friendly. Their manual sucks and will only provide tech support for $80/hour. I bought a Belkin router and got it working for my MacBook. BUT my roommate can't connect, even tho her MacBook sees the network. And I can't print to my wireless printer even tho it says everything is fine when I run the wireless diagnostics.The ISP has these rules:
- Only connect the router to the Internet or Wan port. Do not connect to the numbered ports (how do I know whether or not I've done that?)
- Do not use static IP addresses
- Do not run a DHCP server
I have a big 2 floor house .I would like to use 3G connection using USB type of modems,like vodaphone or MTS. which router to be used so that I can get good connectivity on both floors. NOTE- I do not want to use cabled internet coonections.
View 2 Replies View RelatedI built my first computer today (woot!) but I'm having issues using my netgear N300 usb adapter to access the internet.
I am using a DLink router but for some reason I am getting some weird issues.
First of all, after using the netgear usb adapter, my mac address is something like E0-xx-xx-xx-xx-xx with the xx being the other numbers. Is having a macaddress starting with E0 wrong? All the other 5 devices on my router have mac addresses starting with 00.
Secondly, I am getting a 169.xxxxxx ip address. This is really starting to bother me because I can't set it up using DHCP.
I have a Verizon MiFi card and 3 wireless laptops that pick it up automatically.....I can't seem to get it set up on the desktop pc.....it doesn't recognize it
View 1 Replies View Relatedjust to mess around i reinstalled xp/formatted drive on dimension 4550. plugged ethernet cord from computer to router but can't get any connection to internet. going through the network wizard makes me set up local networks. tried to install new drivers from download page nothing is working.when i open the network connections page under control panel no LAN shows up or anything.
View 3 Replies View RelatedI live in an area that has no cable or dsl internet available.The only options are basic dial up or wireless internet through one of the cell phone companies.Right now I use verizon with a usb adapter.I have had this since moving here.It gets good speed and I share it witht the other 4 pcs in my house through a 5 port switch using windows xp's ics(internet connection sharing)We mainly use the internet for playing games together online.Recently though i have wanted to upgrade to a wireless network.I feel as if I 'm living in the stone age because everyone else I know is using wireless.Last night I went out and purchased a netgear n750 duel band router(model number wndr4000-100nas) after reading several guides online about how to set it up.It sounded easy enough but after 3 hours I still could not get it working.
Here is what I am trying to do.I want to basically turn the router into a switch by disabling it's routing function and let the pc that has the verizon wireless card be the host and hand out ip addresses to the other pcs.(like it is doing now)Problems I am having
1- keep getting the work offline popup when I click on anything in the router control panal(it say you are not connected to the internet would you like to connect or continue to work offline I hit work offline and it just pops up again when I click something else)
2- I think I found how to change the router's ip address and disable DHCP under lan controls but when I hit save it pops up saying I need to manually change my pc's ip address and it will not save.
I am using winxp32 sp3 and right now 5 gigabit wire lan cards.(though if I get this working I'm going to pick up wireless card for 4 of the pcs.)
Earlier today I attempted to change the setting on my Westell 6100 modem such that it would simply bridge the connection to my Linksys WRT54GS router, basically involving setting the router to bridge only and turning DHCP off. Now I no longer get an internet connection through my router when previously the connection had worked perfectly fine before. I following the steps of cloning the MAC address to the router and have done the proper resetting steps (computer, them router, then modem) but I simply can't get an internet connection through my router. The process to set up simple bridging from the modem what supposed to end up with the internet light no longer turning on but the light turned back on following one of the resets.
Currently, I can connect to the internet through the modem just fine but I get nothing when I include the router. I'm not sure if there are some other settings I'm supposed to be changing as I can't seem to find anything past what I've already done when researching online. At this point I would just be happy reverting the settings I've changed but I don't know how to access the modem now that DHCP is off.Basically, I'd prefer to be able to get the router working with these new settings but if that proves too difficult (as I've heard it can be when trying to get Westell modems to work with Linksys routers) I'd like to learn how to access the modem and change the settings back to what they were (preferably in as simple terms as possible as I don't particularly understand what a lot of these settings/configurations do).(And a bit of an aside, but I had attempted to do this modem bridging to "fix" perceived internet speed problems. I've been averaging around 300Kbps download rates ever since I've had this internet connection from Verizon when the supposed download rates should be between 1MB and 1.3MB. Doing this modem bridging had been reported to fix some modem/router conflicts and improved connection speeds for some.)
We have two 2811 router with configured interfaces:
Router1
interface FastEthernet0/0.380 encapsulation dot1Q 380 ip address 192.168.232.18 255.255.255.248 no snmp trap link-status crypto map clientmap!
interface FastEthernet0/0.382 encapsulation dot1Q 382 ip address 10.132.1.126 255.255.255.252 no snmp trap link-status
interface Vlan1 ip address 192.168.5.1 255.255.255.128 ip nat inside ip virtual-reassembly
ip route 0.0.0.0 0.0.0.0 192.168.232.17
ip route 10.132.254.35 255.255.255.255 10.132.1.125
Router2
interface FastEthernet0/0.197 encapsulation dot1Q 197 ip address 192.168.222.2 255.255.255.248 ip nat inside ip virtual-reassembly no cdp enable
interface Vlan1 ip address 192.168.1.1 255.255.255.128 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452
So my case is: computer from router1's network can ping 192.168.222.2 (router2 -FastEthernet0/0.197 )computer from router2 network can ping 192.168.232.18 (router1- FastEthernet0/0.380),but can't ping 10.132.1.126 (router1- FastEthernet0/0.382).
How can i connect vlan 380 and vlan382.I want the three vlan to see each other.Is this happen with IRB or not?
I have a 2811 that is my HQ router with a 10MB pipe. I was trying to configure a IPSEC tunnel to connect to my ASA that has access to our companies internal servers on the 10.33. and 172.16.31 network. I am having a problem getting phase 1 to even come up. I've looked over the configurations and unless i'm overlooking something I dont see what could be keeping it from at least completing phase 1
Below are the configs.
2811-CFG
crypto isakmp policy 10
encr 3des
hash md5
[Code] ....
my problem is this:we have two 2811 router with configured interfaces:
Router1
interface FastEthernet0/0.380 encapsulation dot1Q 380 ip address 192.168.232.18 255.255.255.248 no snmp trap link-status crypto map clientmap!
interface FastEthernet0/0.382 encapsulation dot1Q 382 ip address 10.132.1.126 255.255.255.252 no snmp trap link-status
interface Vlan1 ip address 192.168.5.1 255.255.255.128 ip nat inside ip virtual-reassembly
ip route 0.0.0.0 0.0.0.0 192.168.232.17
ip route 10.132.254.35 255.255.255.255 10.132.1.125
Router2
interface FastEthernet0/0.197 encapsulation dot1Q 197 ip address 192.168.222.2 255.255.255.248 ip nat inside ip virtual-reassembly no cdp enable
interface Vlan1 ip address 192.168.1.1 255.255.255.128 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452
so my case is:computer from router1's network can ping 192.168.222.2 (router2 -FastEthernet0/0.197 )computer from router2 network can ping 192.168.232.18 (router1- FastEthernet0/0.380),but can't ping 10.132.1.126 (router1- FastEthernet0/0.382)How can i connect vlan 380 and vlan382.I want the three vlan to see each other.Is this happen with IRB or not?
For some reason I cannot seem to get a connection between the router and the switch. I see the FE ports on the siwtch, sh ver includes all 18 FE ports, but it seems that there is no backplane connection. The only way I can get conenctivity to the switch module is to jumper between one of the routers FE ports and a NM port. The switch will not accept any IP addressing on the same network as the router becasue of overlap. Am I just being stupid? My understanding was this NM would have a backplane connection to the router. Some docs mention a GE conneection that should show up and there were two parts to the config, one to set up the interconnect and then to set up the switch.
View 4 Replies View Relatedwhat is the simplest way to create backup WAN connection?I have setup 2 WAN connection(2 ISP, 1 is DIA w/ fix ip, 2 is 3G), but if I enable both interface ,then I unplug WAN 1. no traffic goes to WAN 2.I have already have 3G connection enable all the time (w/ command "dialer persistent") Cisco 2811+ Cisco-HWIC-3G,
View 4 Replies View RelatedI have two ISP need to connect them on my router.
The Router that I have is 2811 where it contains two Fa ports only, so I put an access switch between the two ISPs and the Fa0/0 then configured the Interface Fa0/0 with two IPs ISP1 and ISP2 as a secondary.
The problem that I faced that when ISP1 become down the another secondary IP (ISP2) stay down and the internal users have no access to the internet.
I'm generally pretty good with VPN issues and with SSL certs, but this is my first rodeo with VPN and certificates together. I've got a Cisco 2811 router running IOS Firewall (12.4(25)) and for a while now, I've had VPN clients connecting using PSK's and XAUTH. In order to tighten security, we'd like to move away from PSK's with Aggressive Mode and use certificates with Main Mode.I've been trying to use the Cisco 2811 as the CA, rather than use a Microsoft server or third-party provider. I think I'm pretty close to getting this to work, but something isn't quite right. My VPN client software does connect to the 2811, and I get prompted for the XAUTH creds. If I supply the right creds, I do see in my VPN log window that I've gotten assigned an IP address from the inside VPN pool, my split tunneling rules come through, but the VPN disconnects almost immediately and I never get a chance to try any pings or to send any other types of traffic. [code]
I have attached a sterilized copy of the 2811's current config (2811_sterile.txt), a copy of the 2811's debug output when the VPN client tries to connect (vpn_client_connect_sterile.txt), and a copy of the VPN client's log with IKE on High and Certificates on High (vpn_log_sterile.txt).FWIW, the 2811 is NOT behind NAT, but my VPN client IS behind NAT. However, I have tried using a direct connection with the VPN client and it didn't seem to change much so I'm not convinced this is a NAT issue.Again, I've never used a Cisco router as a CA and I've been battling this problem for several hours now so the 2811's config may have a lot of unneccessary lines in it at this point.
We have two logical connection which are connected via 1 physical Ethernet interface to 2 routers in central sites. Both connections are 2 Mb/s. How can i classify the output traffic in order to shape both direction to 2-2 Mb/s.
There are not suitable "match" command!!! ??The branch routers are 2650xm and 2811.
I am having trouble setting up a EHWIC-VA-DSL-A= card on my cisco 2811 running the following the following:c2800nm-adventerprosek9-mz.151-4.M2.bin and C2800NM_RM2.srec.124-13r.T11
My hardware supplier tells me its the right adsl card (have 1 existing working card not the same) but the card will not detect on the system to be configured.is this the right card? am I missing something?
I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
What are my best options to secure branch office connection to HQ over Provider MPLS cloud. Our existing Setup
<<HeadQuarter>> :: DataCenter hosting Email, ERP, Intranet, Voice Services 10mb link to Service Provider over MPLS CloudMPLS is terminated on a 3825 Router running advance Services
<<BrancOffice>>::Total 10 In Country Branch Offices2mb Link to Service Provider over MPLS CloudTotal users in each branch : 20 MPLS is terminated on a 2811 Router running advance Services
Router 2811 got 3 Interfaces. One Interface connected to INTERNETProvider, Second Interface connected to Sales_Dept, Third Interface connected to Business_Dept. Internet Bandwidth in Total is 8MB. I need assistance to allocate 6MB total bandwidth to Sales_Dept and 2MB total to Business_Dept Sales_dept has 48port switch 2960, Business_Dept 24 port switch 2960. Gateway for users is the 2811 Router and both are on different subnets
View 3 Replies View RelatedI have a cisco 2811 router doing nat on my home network and it works fine.I've connected a cisco 2621 router to the 2811 both have serial T1 cards, I have enabled IP routing on both and have eigrp 1 process running. I can ping and telnet to each router and they are advertising the networks on each other. when i do a traceroute on the 2621 to an outside address or name example [URL]I get no reply.
View 4 Replies View Related[OK] Site to Site IPSec + GRE = success, no problems.
[OK] IPSec remote access = success, no problems.
[NO] SSL VPN = remote users can successfully connect to all internal systems. Cannot pass traffic to the Internet.
Hardware:
Cisco 2811, Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(22)T5, RELEASE SOFTWARE (fc3) . Software: Cisco Any Connect Secure Mobility Version 3.1.01065
Single hub router terminating IPSec+GRE site to site, IPSec remote access, and SSLVPN remote access VPN services. All services currently configured and running successfully with the exception of the SSLVPN service. Remote users can initiate and successfully establish SSL VPN sessions. While established, connectivity to all internal systems/resources are successful. Only when the remote access client tries to connect to "Outside" Internet resources does traffic not pass successfully. Troubleshooting has pointed to a NAT related issue (I believe).
When connecting from a remote access workstation, utilizing IPSec remote access client (built-in Cisco IPSec client from Mac OS), the session establishes and the client works flawlessly. Examining the Cisco 2811 router, you see the /32 host route from the remote access session get installed, and you see the corresponding NAT translation entries created when the client accesses outside (Internet) resources. Appropriate configuration to implement "hair pinning" have been included to handle the in and right back out (with NAT translation) needed for remote clients to access the Internet.
Configured the 2811 for SSL VPN, and remote access clients can successfully connect and access all internal network resources. Examining the Cisco 2811, the /32 host route for the remote access client is installed, pointing to SSLVPN-VIF0 interface with a next hop of 0.0.0.0 When checking the NAT translation table, there are NO entries for the remote access client address created which leads me to believe the hair pinning/NAT function is not being invoked for SSLVPN clients.
Originally, the IPSec remote access VPN local pool was 10.0.100.0 /24. To keep from having to adjust the existing NAT translation, PBR Route-MAP for the hair pinning function - I took the 10.0.100./24 and broke it into a pair of /25 networks. Bottom half for the IPSec remote access VPN pool (10.0.100.0 /25); upper half for the SSL VPN pool (10.0.100.128 /25). By utilizing SSL VPN, is the traffic somehow bypassing the DIALER1 interface where both the crypto map (and more importantly: IP NAT OUTSIDE, and PBR configuration for the hair pinning function)? I cant explain why NAT translation entries are not being created for SSLVPN client sessions.
Cisco 2811 Configuration has been included. IPSec & SSL VPN Remote Access Sessions Captures (performed from same remote client) have been included.
I have a Cisco 2811 Router with a NM-16ESW card installed. I've connected this to my DSL connecting and I'm trying to build myself a learning lab. From the router I can ping to the internet and back to a test computer I have connected to one of the card's ethernet ports. From the test computer, I can ping the router's WAN interface, but no further. [code]
View 10 Replies View RelatedI have a big issue in providing internet service to the networks that are connected to a router. Also i do wanna know whether ipv6 can be used in 2811 routers.
View 2 Replies View RelatedA pen test has shown I have crackable transform set on my firewall. I can see the config this relates to and do have higher encryption available. What I dont want to do is remove it until I know my remote sites are not using it.does any one know a command that shows all the policies/encrption in use?
View 5 Replies View RelatedI am wondering if this Cisco ASA 5505 Box is overkill for what I need?I have just become network admin to a small office that host two domains.
[code]...
Some of the clients are requesting a connection to the office from remote locations for file access and what not. So would implementing a Cisco ASA 5505 be overkill? I am a bit nervous of going forward as I have never had to "setup" an ASA box and dont want to kill the network.If I should NOT use this box, what should I use for a VPN connection?
