I have a big issue in providing internet service to the networks that are connected to a router. Also i do wanna know whether ipv6 can be used in 2811 routers.
View 2 RepliesI have a Cisco 2811 Router with a NM-16ESW card installed. I've connected this to my DSL connecting and I'm trying to build myself a learning lab. From the router I can ping to the internet and back to a test computer I have connected to one of the card's ethernet ports. From the test computer, I can ping the router's WAN interface, but no further. [code]
View 10 Replies View RelatedI have a sonicwall firewall connected to the LAN port of the RV016 router and two DSL modems connected to the WAN ports.
Ip address allocation:
Firewall
192.168.50.9
RV016
LAN - 192.168.50.10
WAN - 192.168.60.1
WAN - 192.168.61.1
What configurations do I need to enter into the RV016 to allow other networks connected to the firewall(192.168.3.0, 192.168.2.0) to access the internet?
when I got past my current hang up, I marked the thread as answered, so I wasn't sure if I should start another or continue on...
I've tried going through that troubleshooting doc, but I still can't figure this out.
When turning on debug for the 2811, I'm not seeing any thing.
show debug
Cryptographic Subsystem: Crypto ISAKMP debugging is on Crypto ISAKMP Error debugging is on Crypto IPSEC debugging is on Crypto IPSEC Error debugging is on
#show crypto sessionCrypto session current status
[Code].....
We are running our internal network on the 192.168.1.x range.
We have just installed a new control system which is running on a closed 192.168.0.x network (no internet access).
What we need to do is use the WRT54G to connect the 2 networks together so that we can VNC into one of the computers on the control system network so that it can be managed.
I have tried connecting the two networks by plugging the 192.168.0.x network into the WAN/Internet Port on the WRT54G, and setting the "Internet Connection Type" to "Static IP" and setting the "Internet IP Address :" as 192.168.1.200 (the main PC I need to VNC into) but cannot ping any of the other computers..
I have a 192.168.1.xxx network connected to Verizon FIOS via Actiontec MOCA / router. I also have a 192.168.15.xxx network connected to Comcast via Motorola VT2442 router (used for Vonage) and a Motorola SB6121 cable modem.
Each network has it's own gigabit switch connected to each router. The two networks are physically separated but switches and routers are physically side by side.
What is the best configuration to allow devices on 192.168.1.xxx network to communicate with devices on the 192.168.15.xxx network (share printers, NAS, etc), but still have each network served by it's respective ISP, and each device still get it's dhcp, dns, gateway, etc from each respective router?
I've been trying to connect my printer to my wireless router/modem. The install program is giving me the following error {The PC and the printer are connected to different networks(192.168.15.0 and 192.168.0.0). They must be connected to the same network. This can happen when you use the manufacturer's default network name (SSID) and another nearby network is using the same name.} I just had the computer built and have been setting it up. How do I know which is the right IP address?
View 6 Replies View RelatedI cant not get to connected to any wireless networks, it keeps saying unable to connect
View 1 Replies View RelatedI have a Cisco 2811 router with C288nm-advsecuruityk9-mz.151-4-4.M.bin IOS version.The router has two LAN interface FE 0/0 and FE 0/1.The router have too, two interfaces ADSL ATM0.0.0 and ATM 0.0.1, both are connect to internet..I need the next configuration.The interface FE 0/0 is directly connect to a Switch A.The interface FE 0/1 is directly connect to a Access Point Cisco.The Access Point and the Switch is not connecting between.The subnet of Switch A and AP are different (Switch A 192.168.180.0/24 and AP 192.168.181.0/24)The devices in the switch A have dynamic IP address, the router must be a DHCP pool to assign theses IP.The device in the AP have dynamic IP address, the router must be a DHCP pool to assign theses IP.I created two DHCP pools in the router, one for the subnet 192.168.180.0 and other for 192.168.181.0, but the devices of FE 0/0 assign IP of 192.168.180.0 or 192.168.181. 0, but not only in the 192.168.180.0.
View 5 Replies View RelatedI have a 2960 and a 2811 with a hwic card I have one port set as 100 meg and another port set at 10 meg. Both are set to access mode. i need one port for failover (10 meg) . I can't do ether channel on the hwic. How do I prevent a loop when I connect my second connection. While having both connections up. Should I use bpdu guard? the goal is to have one port fail over if the 100 meg goes down. And I'm currently running ospf so it should take the faster connection.
View 1 Replies View RelatedWe have three computers (one of which acts as a file server) plugged directly into an internal office network. Then we have another such connection leading to the WAN port of a router which shares a single connection among another 5 or so computers & laptops. So the WAN connection is providing internet access AND access to the file server.
Since upgrading to a new router, it is now not possible to "see" the file server from the computers connected to the router, although the internet can still be accessed without a hitch. This has now become infuriating as I've spent several hours changing all possible router & IP settings to no avail.
I've been looking around for more information on this topic but I couldn't find quite the specifics I'm looking for.In the most basic text, I want to connect two networks together via the internet and VPN. I currently have two Windows 2k8 Servers housed at both locations. I've tried to do as much as I could myself but clients on both sides cannot access each other.I set-up the Remote Router function on both Servers and connected them but I still cannot ping or access any of the remote resources on that network.
View 1 Replies View RelatedWhy isn't it possible to make following configuration:
View 9 Replies View RelatedI need Know what connection is using on Cisco 2811 router.I have this interface in Cisco 2811, I need Know if this port is connected to Fiber or Copper. I think is copper with RJ45 but I see 100 base TX/FX so this make me doubt about it because TX its for copper link and FX for fiber. [code]
View 5 Replies View RelatedI have a 192.168.1.xxx network connected to Verizon FIOS via Actiontec MOCA / router.I also have a 192.168.15.xxx network connected to Comcast via Motorola VT2442 router (used for Vonage) and a Motorola SB6121 cable modem. Each network has it's own gigabit switch connected to each router. The two networks are physically separated but switches and routers are physically side by side.What is the best configuration to allow devices on 192.168.1.xxx network to communicate with devices on the 192.168.15.xxx network (share printers, NAS, etc), but still have each network served by it's respective ISP, and each device still get it's dhcp, dns, gateway, etc from each respective router?
View 10 Replies View RelatedSo basically I need to hook up a HP LaserJet P2015 to a business and home network. LaserJet P2015 user guide. I would like to keep the printer's ip static so it will stay the same on each network individually. am using a business router (Linksys RV120 W Wirless-N VPN Firewall) with two VLAN (business and home network) built using this router. Also I have two access points both being used to expand this signal through out the building, but not as an extender. They are two Linksys WAP54G access points. The access points are used to expand the home network, and not the business network.
View 1 Replies View RelatedI'm trying to advertise the branch LAN subnets via OSPF back to our core.I can create the OSPF adjacency and the ASA is learning routes fine. However it does not appear to be pushing the branch LAN subnets to the connected router. show ospf database reveals they're not in the OSPF database.Here is my routing config, the branches are 10.114.0.0 /16.As an aside, why I need the statics below, they appear to be necessary to reach my LAN subnets behind the EZVPN spoke sites. I would have thought the ASA would learn it automatically as I'm running network-extension mode on the spokes. [code]
View 1 Replies View RelatedI have a cisco 2811 router doing nat on my home network and it works fine.I've connected a cisco 2621 router to the 2811 both have serial T1 cards, I have enabled IP routing on both and have eigrp 1 process running. I can ping and telnet to each router and they are advertising the networks on each other. when i do a traceroute on the 2621 to an outside address or name example [URL]I get no reply.
View 4 Replies View RelatedI have 3 Macs (OS 10.6.8) and one PC (Windows 7) at work. They are all connected to the company network for internet and access to shared network drives.The computers are used for media (mostly video) production and we need to move large files between the computers easily and quickly. The current network (company wide) is slow and unreliable, so I would like to create a separate network for these four computers and have them connected to both the company network and the office room network. Each computer already has two network ports and I have a router I can use.
View 3 Replies View RelatedBasically, the issue I am having is we have a class b network ID of 172.16. We had a new phone system installed last year which needed to be on an isolated network as our switches do not have QoS on them. Plus they are quite bad...
Some genius decided to use the same network ID on the new phone system as our current network but they are totally isolated networks.
This is where my laziness comes into play... We use a laptop connected to the phone system's network to connect to configure the phones etc but I would like to do this at my desk. So what I have done is configured a wireless access point on the phone systems network so I can connect to it on my laptop to theoretically make changes to the phone system on my PC, but also staying connected to our network for obvious reasons... I do have some networking knowledge, and I am assuming the routes are going to be completely wrong because of the same network ID issue not allowing me to connect to the phone system on my laptop. But I am not sure if I can add a static route to resolve this.
Interface List
0x1 ........................... MS TCP Loopback interface
0x2 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8
[Code]......
i have two linksys wireless router on different networks that i want to connect. how do i go about it?
View 1 Replies View RelatedMy boss's old Windows XP laptop was able to connect to open wireless networks automatically so he never had to click that icon on the bottom right to check signals or anything like that. Is there anything like that I could set up on Windows 7?
I realize that this is not secure and very silly. I suggested choosing the best and trusted networks available. My boss, however, doesn't want to accept that he should have to go through more steps with newer technology. So in this case, I'd just like to give him what he's asking for.
We have an inside interface, 192.168.10.0/23We have an outside interface, public ip...We have the ASA connected to 5 site to sites, this is working fine and through the internal interface can access all remote sites and vice vera. These are 192.168.20.0/24, 192.168.30.0/24, 192.168.40.0/24, 192.168.50.0/24 and 192.168.60.0/24,When a user connects via Cisco VPN Client they can see the inside network but can't talk to the remote networks connected, for instance 192.168.40.0/24... whereas an internal user can. I understand that the VPN client connection is seen as an outside connection, not an inside connection... but then I read [URL] and I am confused even more.
View 8 Replies View RelatedWe recently changed locations and acquired a new circuit from our provider. They also connected our remote branch office to our main office through MPLS. Now, as I understand it, the branch office basically connects back to the main office through our providers network (MPLS). We have a new router at the branch office which has a gateway of 192.168.1.225. The clients in that office have IP's of 192.168.1.96 - 100, using the gateway of 192.168.1.225.
The main office network is 192.168.0.0 (Gateway of 192.168.0.1)
At this end (Main office), I also have a new Cisco 2900 provided by the ISP, with port 0/0 for the outside connection (connected to the 0 port on my ASA 5505). The ASA's port 1 obviously running into my network hub. The provider tells me that port 0/1 on the 2900 is or should be used to connect the branch office back to here and has an IP of 192.168.0.225, as that's how the provider provisioned it. So, I plug that into the ASA's Ethernet port 0/2. And I'm assuming they have a route setup either on the 2900 or the router in the branch office so that 192.168.1.225 can reach me here at 192.168.0.0.
There is already a static route setup on the ASA: (192.168.1.0 255.255.255.255 192.168.0.225 1). As soon as I plug in the cable, the IP phones at the branch office work, but they can't access the internet or any resources in the main office. My questions are:
1. Shouldn't I be able to just go straight from the 0/1 port on the Cisco 2900 to my hub. At first I was plugging right into the ASA, but I don't think I need to do that, why go from the branch office through my ASA to access resources and then back out the ASA for internet. If they're already coming from 192.168.1.225, through the MPLS network, then they should go right to my network and then back out the ASA.
2. They have to route through the ASA first, in which case, do I need to setup another VLAN for that branch network in conjunction with a static route? I can ping the router and hosts in the branch office through the ASA only!
Below is the running sanitized config:
Result of the command: "show running-config"
: Saved:ASA Version 8.2(2) !hostname ciscoasadomain-name audiology.orgenable password ulzaQiFnKVzDwUmW encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Vlan1nameif insidesecurity-level 100ip address 192.168.0.1 255.255.255.0 ospf cost 10!interface Vlan2nameif outsidesecurity-level 0ip address 1.2.3.4 255.255.255.240 ospf cost 10!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!boot system disk0:/asa822-k8.binftp mode passiveclock timezone EST -5clock summer-time EDT recurringdns server-group DefaultDNSdomain-name audiology.orgsame-security-traffic permit inter-interfacesame-security-traffic permit intra-interfaceaccess-list
[code]....
Adding a second DAP-1522, They have 1 DAP-1522, they set that up useing the WAP(button on the side), This one is running in the frontroom of the house and the 2nd bridge will be running in the bedroom of the house.She has tried to click on the WAP button on both Dap-1522's and then the router to sync but thats not working, from what we can tell. I think I will need to manually config them now that a second one has been introduced.the frontroom Bridge is 192.168.0.50, but we cant find the ipaddreess for the second dap-1522 at this time. So question to all, if I can - Is there a way to identify all of the Dap-1522's on the network or anything that is connected on the network. as the DIR-655 is only showing 2 things connected?Right now I wish she would have listened too me and had her house wired for ethernet when the house was being built.
View 1 Replies View RelatedI have two dir655 routers that are connected. The second router is not setup as a wireless access point, but I am open to that if it will work. The second one is going to serve as a public wifi in a business, with a separate SSID. The first one is going to handle the local business network, with its NAS and printers. How would I prevent the public wifi from accessing the first router?
I have tried the guest wifi partition setting, however it still allows access to the lan devices on the first router. It does partition with the second router properly though, but thats not worth anything to me cause there are no lan devices on the 2nd router.
Would it work right if I turn the 2nd router into a access point, disable the dhcp server, and set it up with the guest wifi partition?
I have five (5) sites all connected via static VPN tunnels. They are all using Cisco ASA 5510s running 8.4(4)1. Any internal IP on each site can ping any IP on a remote site, because of the static VPN tunnels. I have the external IP (routeable) addresses connecting to each other.
Site A: 10.1.0.0 /24
Site B: 10.2.0.0 /24
Site C: 10.3.0.0 /24
Site D: 10.5.0.0 /24
Site E: 10.10.0.0 /20
I have remote users who connect using Cisco AnyConnect 3.1 to Site E. They get a static IP within the 10.10.100.0 /24 subnet (vpnpool00) and can access anything in the 10.10.0.0 /20 subnet. So far, so good.No management wants users to access devices within the other sites, specifically Site A using teh same AnyConnect connection. In other words, they get an Ip address of say, 10.10.100.5 and now need to access a server on Site A's subnet or 10.1.0.5.I have checked my NAT statements and they appear to allow this, but so far when I do a ping I get the following: Routing failed to locate next hop for ICMP from outside: 10.10.100.5/1 to inside: 10.1.0.5/0 What am I missing? Is there a NAT statement that is wrong, or an access-list statement or possibly a static route?
I've found that Android devices (smartphones for sure, and perhaps other devices, like Windows Vista/XP pc's with some Atheros wi-fi adapters) can't connect to our eduroam network (WPA2 Enterprise) if the Access Points (all from Cisco) also have open SSID's configured in it. Once I protect the open networks with, for instance, WPA-PSK, the Android devices immediatly get connected to the eduroam. Is there any fix that can be applied to the Access Points. Below there's a list fo AP models and IOS version we have running. I may mention that this problem doesn't occur with Access Points from other manufacturers like, for instance, Meru Networks.
In the AP's event log appears the folowing:
"Packet to client 0026.3778.081f reached max retries, removing the client"
The steps to mitigate the problem above were applied, but with no results.
PS: The Android versions may vary with the same symptom.
Device types: AP 1100; AP 1130; AP1140;AP1210;AP1250
Play Max N600 HD (F7D4301) Dual network operation - on behind Belkins firewall. I have just changed the structure of my network for reasons of additional services being added. I now have in the front room the ADSL modem connected to a switch and 2 PC's. The switch is also pbugged into an ethernet plug in the wall which feeds to the other end of the house where the Belkin router is. I have all devices working on the internet correctly. The issue is getting access between the two networks and the devices on the two networks. I have added the ip addresses of the PC's to the router's LAN/Static Route, but that didn't work. The network in front room (after ADSL Modem is 192.168.1.x and after Belkin router it is 192.168.2.x. Is there a way I can allow access between the two networks between devices?
View 2 Replies View RelatedMy Dell XPS (Windows XP) is not connecting to my network..can't get anything to show up on the networks in range list. My other laptop is fine. But I just upgraded to Firefox 4 on the Dell, and then the connectivity went askew.
View 2 Replies View RelatedI have a brand new Dell Inspiron 1764 laptop that I received on the 25th of June. It is "replacing" a Dell Inspiron 9100 that has gotten to be too slow and bulky for my needs. For support purposes, both laptops are running on Windows 7.Overall, I love my new Inspiron 1764. However, I have noticed seriously degraded connection/signal strength with the wireless card (Dell Wireless 1397 WLAN Mini-card) compared to my Inspiron 9100 (Dell Wireless 1350 WLAN Mini-PCI card).
In areas of my house that my 9100 can get full signal strength (5 bars), my new 1764 is getting 2 or fewer bars. This behavior is also not limited to only my house, as I have tested it at my job and in an area less than 10 feet away from the wireless router, I have "Internet connectivity problems".
I tried twice this morning to speak with Dell support. The first person I spoke at least initiated a DellConnect session with me so that they could check some of my settings and such (however, why they went twice into my sharing settings I could not determine since they have absolutely nothing to do with signal strength.)
Unfortunately, I was disconnected from the session when I went to an area that had less signal than right next to my wireless router.I then got back on chat support with Dell and received another technician to speak with. I explained my problem, told them that I was in a DellConnect session with the other technician, and they looked up my support contract.They then told me that my warranty does not cover software issues and referred me to the software department and told me it would be an extra charge. I told them that I did not believe it to be a software issue in any way, shape, or form. They told me that it must be a setting issue. I have since spent several hours scouring the internet forums on Dell and other websites checking people who have had similar issues. Some of their issues were admittedly from software settings, but I have still yet to find anything that indicates to me that I have an incorrect software setting.
As of this writing, I am standing in my kitchen, typing on my Inspiron 9100 with a full 5 bars, while my Inspiron 1764 sits next to me with a measly 2 bars, and I am literally standing 7 feet above the room that houses my Linksys WRTU54G-TM router.Personally, I suspect a faulty wireless card, but how do I convince Dell to hear my case and replace it rather than trying to bilk me for unneeded software support?
I need setting up two networks to use the same internet connection.Network A is on IP range 192.168.1.x and Network B is on 192.168.0.x and the firewall with internet connection is on Network A at 192.168.1.2.Network B must be on diffrent IP range that Network A can not access it, but the two networks are linked with a Linsys Cisco WAG120N router.Network A can access the internet fine as use gateway ip 192.168.1.2 but how do i get Network B to use that same gateway/internet connection?
View 3 Replies View RelatedI am having trouble connecting my device to certain WiFi networks. We work with hotels and we have a handful of devices that are just not able to connect to their network. Te device works fine in my office. When I get to the Setup page and do a site survey, it'll get to 100% and then display a "page can't be found" as oppose to showing me that it has been connected. We had the MAC address cleared in their network and still no luck. Firmware has also been updated.
View 7 Replies View Related