WCS version: 7.0.230.0. I import a map to WCS then open Map Editor, scale the floor and then draw the walls. But the next time (for example the next day) I open Map editor the walls have moved about 1-2 meters. Often to the left and/or up. This mess up my RF predictions. I have tried Internet Explorer 8, Chrome, latest FireFox. Om rare occations the walls are in their correct place, but most often not.
View 1 RepliesI have enabled the following attribute...Show Pre-connect Message—Displays a message to the user before the user makes the first connection attempt.Where do you actually enter the text for the message?
View 1 Replies View RelatedI am running some tests with Cisco Anyconnect 3.0 and trying to configure profiles with profile editor. my understanding is that when we configure a profile under the AnyConnect profile editor, it will be used automatically when client connects to the SSID.
I have downloaded both the profile editor and AnyConnect secure mobility client, when i create a new profile and save it under "Network Access Manager newConfigFiles" folder, it seems the profile does not take any effect when i try to connect to the SSID, I am still propmted for user credentials when I try to connect to the SSID. I read from somewhere that a profile should be created using profile editor when using EAP-FAST, otherwise connection would fail, I did find failures when using EAP-FAST however this does not happen if I use local auth (on wlc or AP).
so the question is how do I suppose to configure profile editor to work properly with AnyConnect? if I have multiple profiles configured under profile editor, then how does AnyConnect know which profile config file to take when i switch between SSIDs?
I have about 1400 devices in LMS for this one customer.
They have 1200+ IOS devices
200 + catos devices
My problem is we use 2 differnt change scripts in Config Editor for IOS and CATOS. I have a list of all of the IOS and CATOS devises in txt format.
Is there some magical way to just upload the txt files into Cisco works instead of searching for them during the Config Editor batch job creator? I find it takes hours to sort this batch job out
Trying to send wifi thru plaster walls (no metal lathe, only wood), no mirrors, no cordless phones and only going about 20 feet. I'm trying to run signal from 2nd floor to first, thru one 4 in wall, an open stairwell, then thru a door or possibly another 4 in wall (depending on route the signal takes)
View 2 Replies View RelatedI can connect to my router with full strength no matter where I am in my house. But the moment the router leaves my sight, I can no longer connect to the internet. I just recently set up this router and the internet was working completely fine at full speed no matter where I was; then all of a sudden I had to be within direct sight of my router just to connect to the internethere is a 6 meter distance between my router and my room. between that is a plasma tv and one wall. I don't live in a concrete bunker with 6ft thick walls.There is only one conflicting channel in the area and it is channel 1. Changing between different channels has no effect. rebooting the router has a momentary effect where I am able to connect in my room at full speed, but it eventually dies and I lose connection again.
View 3 Replies View RelatedI need setting up a wireless home network. I have never done much networking, beyond linking two PCs directly together. This is my first time setting up a network that has multiple PC/devices accessing it.
It's a big house and has two floors. More importantly, it has impossibly thick walls. The walls are between 18 to 24 inches of solid stone (perhaps to repel a tank invasion?). I want to be able to get at least 15-20 Mbps to the furthest reaches of the top floor, in order to stream high quality HD video without a hitch.
I have settled on the ASUS RT-N16 router, unless a better option presents itself. It's one of the more decently priced high-end router available to me. It has decent signal strength (3rd on the MaximumPC router round-up), supports Tomato USB etc. I also intend to use the router to as NAS, plugging in an external HDD to one of the USB ports provided.
Despite its decent wireless strength, I doubt I will get close to the required Wifi throughput. Here is my plan to get around that. Let me know if there are any problems with it or if it can be done better. I intend to run an Ethernet cable from one of the router ports to the top floor, and attach a cheap .n router at the other end, to act as a wireless access point.I am unsure if this will meet all my requirements.
1) Will there be any problems with having one router connect to the other?
2) Will external HDD connected to the RT-N16's USB port, configured as a network share, be accessible as such to any device connecting to the secondary network?
3) What kind of cable will be needed to connect the two routers (provided this configuration is viable)? I remember that cable type used to depend on what's connecting to what, e.g. cross-crimped cable for attaching two computers directly without a hub or switch etc.). I don't know if these concerns are still valid.
4) Will I be able to access the configuration page of the primary router from devices connecting to the secondary router's network? I intent to run some apps on the primary router and would like to be able to check on them from the upper floor as well.
5) Will there be an impact of the speeds? The N16 as Gigabit Ethernet ports, which I doubt the cheap router will have. I don't think that should effect the speeds, but like I said, I have next to no experience in this area.
Will an E4200 router solve my problem of getting through 5 walls and 66ft range?I have a signal strength of 5% only and I want to avoid using an RE1000 extender signal since they are incompatible with osx lion.
View 9 Replies View RelatedI'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.
View 1 Replies View RelatedWe are about to share a 10 MBit ISP connection with 2 others companies, and they are going to split the bill up into 3,3 and 4 Mbit, so we where thinking that we could setup a switch before their and ours router and provide them with a static IP from our ISP. But is it possible to set a bandwidth limit on the ports of a Cisco Catalyst 2960-8TC, so that we can set a limit of 3,3 and 4 on 3 ports.
View 1 Replies View RelatedI want to PAT my project of WLAN and i attached the document, how I create the Testing Criteria of the said scenarios, PAT document includes WCS 7.0, WLC 5508, MSE 3310, Cisco AP 3502e and ACS 4.2.
View 0 Replies View RelatedI have cisco ASA5510 firewall using in my network but unable to bolck Url's unwanted. can i block the [URL] on the asa by using regular exp.
View 3 Replies View RelatedI have 7 POE switches that have ESI IP phones attached. I have two VLANS, 1 and 2. VLAN 2 is used for voice and is defined in each switch.The ESI IP phones connect to my POE switch ports and the pc attaches through the ESI IP phone.
I have had voice quality issue between floors in my building. Talking to others on my floor via the IP phone, there are no voice quality issues. [code]
is it possible to connect Cisco Ap-1242AG with non-cisco wireless router to work as repeater?
View 1 Replies View RelatedI am looking at a config on a 5550 FW, and am trying to make sense of the syntax of the following rules. I have been to the Cisco site, but can't find much on the syntax.
View 8 Replies View RelatedI currently use a device called the Access Enforcer which runs OpenBSD. I have 3 stable, working VPN tunnel's where the other side's device is a Cisco ASA 5520 or 5540. I was setting up my 4th VPN where the other side used a Cisco ASA 5520 and ran into issue's. The Cisco side can bring up the tunnel. Once the tunnel is up each side can talk to the other side. However, when the tunnel is dropped, the OpenBSD side cannot bring up the tunnel. The error received is on the OpenBSD device is "isakmpd[29581]: transport_send_messages: giving up on exchange from-XX.X.X.0/24-to-XX.XXX.XXX.240, no response from peer XX.XX.XXX.141:4500". I have been trying to figure this out for weeks now and can't seem to find the cause.
View 3 Replies View RelatedI am trying to configure a 3750G that has been sitting on the shelf for several months and am getting the following error -
% Error: Unable to create flash:/microcode_update% Error: It must not already exist
Normally, getting an error during POST isnt a good thing. My first thought was that flash was corrupted or flagged RO somehow. I did fsck flash: with no change. I next tried fsck /test flash:. It tested 77 blocks and performed 0 erasures. It had been running for about 15 minutes with no problems reported so far. Multiple reboots of the switch still report the same error.
I have reviewed the history of what I have done on this switch and finally think I found the problem. I noticed a microcode_update directory that I am not used to see on a 3750. Deleted the directory using the rmdir command and rebooted the switch. On reboot, I noticed that a front_end/ directory was listed as being created as well as fe_type_1 and fe_type_2 were created. The switch now boots up without any errors.
I have two Cisco Aironets 1401 connected to a Cisco Catalyst 3560 Switch. When users log onto the Wifi the APs authenticate with a Freeradius that then authenticates with LDAP.
Recently users have been getting kicked off of the network but I'm not sure why.If so how do I set these APs to roam with my setupd?For all I know there could be an issue with the switch I'm just not sure where to start when it comes to troubleshooting this issue.
Guys I am using a cisco 2911 router with three interfaces: Gi0/0 connected through a switch to all my servers and Gi0/2 which will connect to another server, and Gi0/1 is my outside interface connecting through a switch to two ISP's.I have webservers and Terminal servers/File Servers with 10.0.0.0 network address connected throught My Gi0/0 interface.Now I want to implement a Cisco Advanced firewall for security on my router using CCP.I want the firewall to work such that it allows external users to access the servers on Gi0/0 through ports 0,23,25,20,21,53, 110,3389. and to access the SIP server on Gi0/2. My issue is can i just create two DMZ's for both interface Gi0/0 and Gi0/2 without creating an inside zone and Gi0/1 as outside zone as my internal traffic is mostly server based and the users connect remotely through terminal server to access resourcess using RDP, secondly how do I open the relevant ports.I have checked alot and all I have seen is just basic process on using the wizard I have no idea how to go about this issue.
View 19 Replies View RelatedI bought a new cisco 3550 switch to prepare for my Cisco certification prepration. Actually i dont know how to connect the cisco switch to a laptop with only usb ports....... earlier i used to do my practise using Cisco packet tracer but i think for CCNP switch that is not enough thats y i bought second hand switch. how can i connect that switch with my toshiba laptop which has only USB ports. do i need to buy some sort of convertor or other hardware. And if so what does u call it and how much does it cost?
View 5 Replies View RelatedI am struggling to have my PPTP traffic to get routed through NAT to reach other Server LAN segment. I am using Cisco 2921 router as a PPTP server.This Cisco 2921 router is working as PPTP server and doing NAT also to reach Server LAN segment (LAN-B).My problem is after PPTP connection establishes I cannot reach any of the LAN segment, but after connecting PPTP I can browse Internet without any issue, but none of the LAN element is reachable. Please have a look on the configuration I am posting 2921 router configuration to suggest something, I have also attached the network setup for better understanding…Just to update Clients in LAN-A can access Internet as well as servers (LAN-B). [code]
View 2 Replies View RelatedI would like to know the IOS which supports :ACL Support for Filtering on TTL Value feature on my Cisco 7600 device. I check on cisco and found the Cisco 12.4T release but this software doesn't fit onto my chasis. which software should I upgrade to on my cisco 7600 to have this feature.
View 5 Replies View RelatedI have a cisco router I would like to reset the password for. Its the first password that is entered. for exampleUser access verificationPassword:I have changed the en password using this command:router(config)#enable secret cisco123 <---example password
View 5 Replies View RelatedI finally got the Site to Site Vpn from our corporate to remote site. Is there a way to connect a cisco phone over that network. Since both Voice Vlans are exempt from acl I would imagine all traffic is clear to go accross? and if so I just have to set the phone to our tftp/ccme. Will that work.
View 2 Replies View RelatedI want to create a user who only has access to "router>" prompt on the CLI. this user should not be able to do enable command and by no other means be able to go to global configuration mode. I know the command router(conf t)# username ABC privilege 1 password ABCPASS, but even with this command, this user gets privilege 15 access.
View 2 Replies View RelatedI have the CISCO 1800 and I have there the HWIC-2T. I have two questions.First is an easy one. I want to replace the HWIC-2T with HWIC-4T but the CISCO 1800 guide and the HWIC-4T guide says that they dont fit together but I inserted the HWIC-4T in to the CISCO 1800 it recognized him with all the 4 Smart Serial ports that it hase. The question is, how can I check if the CISCO 1800 supports the HWIC-4T?Second question is how can I configure one of the Smart Serials in the HWIC-2T/4T to comunicate with the X.25 Protocol? What I have now is at one end CISCO 1800 and at the other end CISCO 2800 and they are comunicating with each other throught one of the Smart Serials they have. I want to connect to each one of then an old pc that comunicate only with X.25 and I want this two computers to comunicate with each other throught those two routers.
View 2 Replies View RelatedWe're currently evaluating Cisco Prime LMS 4.2.Something we've been trying to achieve for the past couple of days is to have LMS notify us when a Microsoft Host is Unreachable, and then to notify us once that alarm has cleared (the Microsoft Host is Reachable again).
We're at the point where the Microsoft Host was discovered, LMS incorrectly identified it as a Cisco Call Manager, so we changed it's identity to non-cisco device > microsoft host > microsoft host. LMS currently has the device listed as being in the 'Questioned' state. SNMP timeout has been set to 15 seconds, and the SNMP community is correct.
Being new to LMS Prime, and having not received any training on the product to this point, we turned to the admin guide, but we couldn't find anything that goes into detail for how to manage the notification for non-Cisco devices.
Is what we're trying to achieve possible with Cisco Prime LMS 4.2? We just want to be able to receive simple 'host unreachable' notifications for Microsoft servers, and the corresponding 'cleared' notifications once the server is back online.
I'm trying to understand CEF; I know it's used most commonly in layer 3 switches but that routers can also do it. The routers that support CEF must have special hardware I'm assuming? (Since CEF is layer 3 processes in ASICs) How can we check if a router is capable of CEF? Does anyone know a good link/graphic that shows how much faster CEF is than software-based layer 3 processes?
View 10 Replies View RelatedBasically, I have a network which has a LAN and a DMZ. I need to isolate a few servers and users from the LAN so I created a VLAN on the switch. I assigned it an IP address in a different subnet and assigned ports to the VLAN. Port forwarding is configured on the switch.For testing purposes, before this goes live, I connected a computer directly to one of the switch ports (ge4/5) and assigned it a static IP in that subnet, the gateway being the VLAN IP. I can ping the VLAN IP but I can’t ping the router or get to the Internet,I tried setting the gateway to the ASA VLAN interface (e0/1.4) with the same result.The 1st step is to get Internet access. The next step will be to allow access to the Exchange server on the LAN.There are many devices not shown on the diagram but the important ones are there.
View 12 Replies View RelatedHaving a hard time getting Cisco phones to roam 'cleanly' in a Cisco unified wireless environment; Cisco 2504 controller with Cisco LAP1142n (lightweight) APs. The phone SSID is not broadcast and is using WEP encryption. The problem is that when the user is walking around the property, traversing from AP to AP in-call (external and internal calls), they notice the point at which the phone roams from AP to AP - it's literally two or three seconds of no sound and then the call resumes back again. Fast SSID change has been enabled, we've tried locking the SSID to 802.11a only, b only and g only but with only slightly better results when locked to B. We've lowered the client roaming threshold RSSI to -75dB from -80dB, this also yielded better results but still a couple of seconds gap exists. Cisco TAC came in on a Webex session earlier, changed a few QoS settings and advanced wireless settings on the controller, but to no avail. Wireless signal has been proven to not be an issue; several AIRMagnet PRO surveys have been carried out showing the signal throughout the property to meet the -67dB requirement.
View 8 Replies View Relatedhow to set-up cisco site to site vpn having dynamic ip address on both sides??
View 2 Replies View RelatedI have the above router and use P2P program to download the odd TV series only thing is that when I'm using Tixati to surf on the same computer or any other computer on the network is very slow. To get around that I only use the P2P when everyone is in bed. Is there any way to limit the bandwidth that the program uses. Also not related to the above question but I have another RV042 in another location using VPN and a wireless router. Looking for all in one solutjon does not have to be a new router was thinking about SonicWall TZ 150.
View 4 Replies View RelatedDoes LMS 4.1 support other vendor devices? If my device is not in "LMS non-Cisco devices" database is possible to add the MIB to manage these devices?
View 14 Replies View Related