I recently upgraded our 5508s to 7.0.98 I am now seeing this message on the primary WLC while running adebug on a client *apfMsConnTask_1: Sep 29 11:05:36.114: Deleting the client immediately since WLAN is changed.
View 6 RepliesI have 2 5508s (foreign and anchor both running 7.2.110.0) with an open WLAN configured via mobility anchors. This configuration works and has no problems. My next task is to incorporate a webauth page (accept/reject) to present the clients with AUP information, etc. On the foreign controller I created a test WLAN (open) and setup webauth Passthrough using the Cisco webauthbundle (wap.html), this works as intended, no issues. However I am at a loss as to how to incorporate the webauth Passthrough functionality on the WLAN that is configured for the mobility anchor.
View 2 Replies View RelatedAfter changing the VTP mode to from client to transparent, I noticed the output of 'show run' now displays the vlans. I don't have any spare 2970s to check this with at the moment. Output of 'show run' looks like this now with vlans info, this was not shown before changing the VTP mode.
vlan 2
name 16.6.16.0/27
!
[Code]......
We use WLC 5508 with 7.4. We tried to set max allowed clients per AP radio to 30 through GUI. We have APs with 80 clients associeted though.
When entering config wlan max-associated-clients max-clients wlan-id we got
"WLAN/Guest-Lan/remote-lan is enabled. disable to configure max associated clients."
GUI doesn't show that message, should it? In GUI, Is it necesary to disable WLAN before too?
The Release Notes for 7.0.116.0 of WLC 5500 has a table which title is "Client Type", and it shows wireless adapters. My question is,
what kind of customer means? Wireless clients or clients for an specific application? If it was the first option, does it mean tha just this adapters could connect to my wireless network?
I recently setup a 2504 WLC that has two primary WLANs (internal and guest) which get their IP addresses from a central DHCP server using the local router's broadcast forwarding. Things seem to be working well for the internal wlan, but clients on the guest wlan don't seem to be getting IP addresses. If I give the client a static IP they are able to communicate across the wlan okay.
It is worth noting that I am using LAG between the controller and router and this guest wlan is really just a regular wlan (with PSK) that has an access-list applied to force it to the internet only. The access-list should be allowing dhcp requests through, but in any case, I removed the access-list and it made no difference.
Here is a debug client for a machine connected to the guest vlan (vlan 33). The internal wlan is on the 10.10.10.0/24 network (same as wired and same that the AP's are connected to) and the guest wlan is 10.33.0.0/16. I don't understand why I am seeing the dhcp request come from the internal vlan/ wlan first and it gets an IP address on this network. I then see a request on the guest wlan/vlan at which point it appears to get a valid IP address on the guest network (10.33.0.0), but the client never sees this. [code]
Having performance issues running two 5508 controllers on the same network? One is running 7.3.101.0, the other is running 7.0.98.0. The legacy APs are connected to the WLC on the older code to support older hardware. The new WLC is accepting all the new 3600 APs. Once all legacy APs are replaced, the 5508 on old code will be disabled.
View 3 Replies View RelatedI have one wlc 5508 running on latest IOS 7.116, there is one wlan abc which i have disable status and disable broadcast, but randomly still i can see from wlc dashboard there is one client connected to this wlan abc. The moment i check on the client details, there is no client connected to that wlan and when return to dashboard, no more client connected to that wlan abc.
View 3 Replies View RelatedHave been experiencing speeds of max 2.5 Mbps for transferring files between Windows 7 machines connected wirelessly to a Billion 800VGT router. A speed of maximum 18 Mbps was achieved. No matter what I did to adaptor settings it was the best possible. Have 6 wireless machines which I cross checked multiple times using Lan Speed Test by Totusoft.I then disabled the wireless security (WPA-PSK) on my Billion 800VGT router and secured the network by using the Wireless MAC address filter. My speed immediately increased to 11Mbps between wireless machines. Speeds to machines on fixed lan increased to 26 Mbps.
View 1 Replies View RelatedI recently installed additional licenses on my 2 WLC 5508s. Then I installed NCS on a virtual appliance. Installed the NCS license, added the controllers, refreshed configs, created templates, etc. However, when I go to look at the License Center, I can't see any controller licenses. When I log directly on to the controllers themselves, the licenses say they are installed and "in use". I've looked all over and cannot determine why the controller licenses do not show up.
NCS version: 1.1.0.58
WLC version: 7.2.103.0
I am working on a new install where the customer is using local RADIUS servers at each of their many campuses (for local dynamic VLAN assignment), while using a single set of controllers at the core of their network. For the record, we have set up a pair of 5508s (v 7.2.103.0) in their central data center with 3602i APs around the various campuses. We are using FlexConnect groups to locally authenticate and switch the users.
Right now, the config is working great as far as authentication and local switching goes. The problem we are experiencing is that none of the authenticated usernames are being passed back to the controller (and ultimately NCS). This makes the tracking and troubleshooting of users difficult. Is there something I am missing here? I can't seem to find any fixes relevant to this issue in the 7.2.110.0 release notes.
Our wireless network has started to drop out periodically. If we pull power and restore, the network immediately comes back up on all our our devices. We have the WRT54G, and we have 2 PCs, 2 Macs, and 3 iPhones, and a wired home phone. Normally there are not this many devices connected, but with everyone home for Thanksgiving and all these devices on the network we have started to see this issue.
Are there simply more devices than the router can handle? Is one of the devices crashing the network for everyone? What typically will cause something like this?
I would like to setup a 2504 to have one Guest WLAN and one Staff WLAN with a controller port for each WLAN connected to different devices.
I would prefer to connect the WLC Guest port to an ASA 5510 and the WLC Staff port to an internal 2960S switch. Will this work? I haven't setup a 2500 series controller previously.
I have a wrt610n that I've used for years with no problem. The usb drive I've had plugged into it has worked great for a really long time, but it's fairly small. I bought a WD 1TB hard drive, formatted it with the router set everything up. after about a day I tried to upload a file from work and got an error, and it wiped the harddrive clean. I reloaded thinking it was a fluke and everything worked fine for about a month. Uploading and downloading worked fine from where ever I was at, on the local network or over the internet. Then I tried to upload a small file, got the error and all of my files were gone again.
View 1 Replies View RelatedI've got the Cisco E4200 v1 firmware 1.0.04I hooked an usb 2.0 enclosure to it running a WD red "NASware" 1TB drive to it.The drive works just fine, brand new, silent, runs cool enough. I'm not saying it's a super-drive, just not complaining of anything.I started using it as a backup drive. File disappear randomly.Gigabytes of files deleted. No power outages nothing happened, the Router is 24-7 on connected to a UPS. So it is the drive, it was never shut off since connected the drive, about a month ago. It only shares connection among a couple desktop PCs a couple laptops a network printer and a couple smartphones, all updated, all clean that is no virus or anythingI removed the drive from the router and plugged it in the computer.Files were there,even though the files in the root were not all there, it must have crashed during the last modifications, although it's bad, and it's also bad that it does not give you a single sign it has crashed.
View 4 Replies View Relatedi sold off my e4200 & brought a e4500 .The e4200 has had a 2 TB W.D external drive attached ,i stream movies to a sat pvr in the .ts format .The problem is i set the e4500 up & it deleted my .ts files not once but 3 times.when i brought the e4500 i did roll the firmware back to the classic non cloud firmware.the third time i had turned the router off & once swtiched back on my files were gone .should i safely remove the drive from the set up ? what if i have a power failure?
View 5 Replies View RelatedI got one issue with the WRT610N and the NAS feature. I am running Vista on a laptop connected to the WRT610N via the 802.11n link but the issue is not here.I have a hard drive of 40GB (but same issue exist with another drive of 500GB) plug to the USB port. I can read all file without any issue. I can also add file without any problem. The problem come when I try to delete some directory. In this case I got the an 0x8007045D Error indicating that I need to have the right permission for doing this. However I do not have any issue in deleting files. In case I delete all files from a directory I can't delete the directory without the error. I map the drive to the windows explorer with the admin account which give read and write access.
View 5 Replies View RelatedIn the process of setting-up a E2500 Linksys router, I set-up my secured network which is working fine but also (I do not know how I did this??) set-up the same named network but it is unsecured. How do I delete this unsecured network.Do I need to set-up the router again?
View 4 Replies View Relatedmy win 7 desktop always disconnect from internet connection after it has been connected and i ran network diagnosis wizard it was saying DNS ERROR CONNECTION. All other systems in my office use the same dns address.
View 3 Replies View Relatedwhere with my computer where it will connect to my network for a second or two then immediately disconnect. Other computer and devices connect without a problem. I have also experienced this with every network I have tried to connect to; it does the same thing. I figure it is therefore a problem with my laptop itself, but trouble shooting has yielded nothing and most of the fixes I have found require connecting to the network, but obviously I cannot do that.I can connect with an Ethernet cable just fine. My guess would be that there is a setting that is incorrect within the wireless on my computer, but what that is I could not even venture to guess.
View 2 Replies View RelatedI just update my cisco 7609 to Version 12.2(33)SRD6. I encounter a strange problem with this version, everytime i change BGP policy ( input or output ) this will take effect immediately without "clear ip bgp neighbor <address> soft". Are there anyway not to take BGP policy affect unless command "clear ip bgp neighbor <> soft" ?
View 7 Replies View RelatedI have about 30 remote EZVPN 1811 routers that never come up after a firewall reload for about an hour. I have watched the EZVPN remotes and they believe they still have an IPSEC SA and they never attempt to reconnect until their IKE SA times out. Is there any way I can change this behavior so that the remotes will more rapidly recognize that their SA is invalid and negotiate a new one?
View 2 Replies View RelatedI am migration an IPsec site to site VPN config to a new ASR1001 router «facing» a Linux box (ipsec-tools + racoon). As the Debian Linux does not offer VTI, I am using a crypto map.
The working config is given below with the corresponding logs on the Linux side.
When I try to apply this previously working config to the ASR1001, I get the following error :
000855: *Dec 12 18:28:21.859 UTC: %ACE-3-TRANSERR: IOSXE-ESP(14): IKEA trans 0x1350; opcode 0x60; param 0x2EE; error 0x5; retry cnt 0
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: initiate new phase 1 negotiation: 194.214.196.2[500]<=>130.120.124.8[500]
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: begin Identity Protection mode.
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: received Vendor ID: CISCO-UNITY
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: received Vendor ID: DPD
Dec 12 18:50:19 FAKE-AUCH-GW racoon: INFO: received Vendor ID: draft-ietf-ipsra-isakmp-xauth-06.txt(code)
I have a 3845 router which got reloaded immediately and need to know the reason for the reload .Router have created crash info detail .
View 3 Replies View RelatedMy HW is Version B2 and my firmware is 2.25. My internet conection keeps droping and reconecting. I started off doing this a few times a day but now it does not keep a connection for more than 10 minutes.
View 5 Replies View RelatedI faced with issue on ME3800. [code] With that configuration there is no problem with DHCP Relay packets.But if I add on interface #xconnect 82.199.1 19.1 77 encapsulation mpls it will stop forward DHCP relay packets immediately. All other traffic transfers without problem.
View 2 Replies View RelatedI recently deleted some devices from LMS. Now, when I run a device credential report, I get the following for the devices that were deleted. Device has been deleted, or is not managed by LMS.
View 1 Replies View RelatedI was trying to erase my lab router 2600 and reset it back to the factory defaults. Well I was able to to reset it all right but I used the erase command which worked a little to well. So now there is no IOS and the router is in ROM mode and I didnt back up the pervious IOS "Nice". So was able to get an updated IOS for my 2600 but I'm trying to install it and don't know how. I was able to get a tftp server app for my windows pc but I'm unsure on how to configure it so I can transfer the new IOS to the router. On the up side I did learn something erasing and reset are to very different things.
View 6 Replies View RelatedHow do I delete a file using command prompt from one computer to another....
View 5 Replies View RelatedI would like to know how to delete a connection from my network. When I connect to the Wii it automatically chooses the right connection. What I have noticed though is that there is a third connection for a printer that is not secured and I have no idea why it is there or has an option to connect to the internet.
View 4 Replies View RelatedA bit of a Catch-22 here: I am trying to delete VPN Group Policies but receive the error message that the policy is in use by a particular Connection Profile. When I try to delete the Connection Profile I receive the message that it is in use by a VPN Group Policy..
What else is there to delete or do I have to use the CLI?
We have configuration of Etherchannel in Cisco 6509 connecting to Cisco 6513 switch, both running on CatOS. This is a group of 8 ports in 6509, due to some reasons one port in Etherchannel group went bad. I have disabled that bad port now. Now I have to delete that bad port from etherchannel group (First task) and add a new port to the group ( 2nd task). I have tried many cisco documents to completely delete the etherchannel port, but no use.
View 8 Replies View RelatedJust looking at a new clients setup and they have a ISAKMP vpn to the old security company I am trying to remove...I am fairly new to cisco, I actually know how to setup the ISAKMP policies, acl's etc but never had to completely remove one before All I can find is Clear Commands which seem to just flush the config not actually delete any of the policy etc...Its not that urgent as all passwords are changed on the domain and the cisco, the usernames have been deleted as well.
#show crypto isakmp peers
Peer: ** Port: 500 Local: **
Phase1 id: **
#show crypto isakmp policy
Global IKE policy
[code]...