I recently deleted some devices from LMS. Now, when I run a device credential report, I get the following for the devices that were deleted. Device has been deleted, or is not managed by LMS.
View 1 RepliesI was trying to erase my lab router 2600 and reset it back to the factory defaults. Well I was able to to reset it all right but I used the erase command which worked a little to well. So now there is no IOS and the router is in ROM mode and I didnt back up the pervious IOS "Nice". So was able to get an updated IOS for my 2600 but I'm trying to install it and don't know how. I was able to get a tftp server app for my windows pc but I'm unsure on how to configure it so I can transfer the new IOS to the router. On the up side I did learn something erasing and reset are to very different things.
View 6 Replies View RelatedHow do I delete a file using command prompt from one computer to another....
View 5 Replies View RelatedI would like to know how to delete a connection from my network. When I connect to the Wii it automatically chooses the right connection. What I have noticed though is that there is a third connection for a printer that is not secured and I have no idea why it is there or has an option to connect to the internet.
View 4 Replies View RelatedA bit of a Catch-22 here: I am trying to delete VPN Group Policies but receive the error message that the policy is in use by a particular Connection Profile. When I try to delete the Connection Profile I receive the message that it is in use by a VPN Group Policy..
What else is there to delete or do I have to use the CLI?
We have configuration of Etherchannel in Cisco 6509 connecting to Cisco 6513 switch, both running on CatOS. This is a group of 8 ports in 6509, due to some reasons one port in Etherchannel group went bad. I have disabled that bad port now. Now I have to delete that bad port from etherchannel group (First task) and add a new port to the group ( 2nd task). I have tried many cisco documents to completely delete the etherchannel port, but no use.
View 8 Replies View RelatedJust looking at a new clients setup and they have a ISAKMP vpn to the old security company I am trying to remove...I am fairly new to cisco, I actually know how to setup the ISAKMP policies, acl's etc but never had to completely remove one before All I can find is Clear Commands which seem to just flush the config not actually delete any of the policy etc...Its not that urgent as all passwords are changed on the domain and the cisco, the usernames have been deleted as well.
#show crypto isakmp peers
Peer: ** Port: 500 Local: **
Phase1 id: **
#show crypto isakmp policy
Global IKE policy
[code]...
We have recently purchased new Sup2T to replace the Sup720. When we tried to copy the vlan.dat file across we are facing this issue. Sup2T is not booting up once delete the original vlan.dat file of the Sup2T & reload. Here is the console output during the process. What to do to get this Sup2T working.
[Code] ......
I have downloaded material to a site many years ago and now that site appears first when my name is typed at Google Search. The problem is that I've written many e-mails to the site manager and he is not answering. Is there any way to delete this site from my Google search?
View 2 Replies View RelatedI recently deleted an account off of my computer, it was just the account I didn't use that had no password, it was not the admin or administrator account. So I deleted it, and went to bed, I woke up the next day and my computer was just finishing installing an update, after it restarted my internet does not work and it has the yellow caution triangle over top. I troubleshooted, and got the message "windows could not automatically detect proxy settings"When I open network and sharing center it would say "identifying" forever and not identify I guess.The weird thing is, my sisters computer and my old computer can connect to the internet fine. I tried bringing my computer next to the router/modem(not sure of the difference) and i plugged the ethernet cord directly into the modem/router into my computer, and it's the same thing. The most annoying thing is that i cannot do a system restore as i have not set it up before hand.(yes i know that is a very novice mistake
View 2 Replies View RelatedI am seeing old entries of phantom folders in My Network Places in Windows 7. In XP you could just delete them, but there is no selection for this in Windows 7. How to delete them?
View 9 Replies View RelatedI have a wrt610n that I've used for years with no problem. The usb drive I've had plugged into it has worked great for a really long time, but it's fairly small. I bought a WD 1TB hard drive, formatted it with the router set everything up. after about a day I tried to upload a file from work and got an error, and it wiped the harddrive clean. I reloaded thinking it was a fluke and everything worked fine for about a month. Uploading and downloading worked fine from where ever I was at, on the local network or over the internet. Then I tried to upload a small file, got the error and all of my files were gone again.
View 1 Replies View RelatedI've got the Cisco E4200 v1 firmware 1.0.04I hooked an usb 2.0 enclosure to it running a WD red "NASware" 1TB drive to it.The drive works just fine, brand new, silent, runs cool enough. I'm not saying it's a super-drive, just not complaining of anything.I started using it as a backup drive. File disappear randomly.Gigabytes of files deleted. No power outages nothing happened, the Router is 24-7 on connected to a UPS. So it is the drive, it was never shut off since connected the drive, about a month ago. It only shares connection among a couple desktop PCs a couple laptops a network printer and a couple smartphones, all updated, all clean that is no virus or anythingI removed the drive from the router and plugged it in the computer.Files were there,even though the files in the root were not all there, it must have crashed during the last modifications, although it's bad, and it's also bad that it does not give you a single sign it has crashed.
View 4 Replies View RelatedI am looking for ways to avoid deleting files from the flash in a Switch 2960, I found some scripts TCL / EEM but this switch does not support EEM (IOS c2960-lanbasek9-mz.122-58.SE2.bin).
View 13 Replies View RelatedI recently upgraded our 5508s to 7.0.98 I am now seeing this message on the primary WLC while running adebug on a client *apfMsConnTask_1: Sep 29 11:05:36.114: Deleting the client immediately since WLAN is changed.
View 6 Replies View RelatedI have a query regarding the deletion and creation of one of my SVI interface on 6513 ,The reason behind it as follows.My traffic get to Internet in this manner
proxy(external int.)[IP:192.168.1.30] --> Gi0/9[6513 in VLAN 170] --> SVI VLAN 170[IP:192.168.1.10] --> Gi0/10[In VLAN 170] -->ASR[IP:192.168.1.20],I need to assign this VLAN ie 170 to my inside interface of firewall but it was mentioned in books like this "Assign the VLAN for the FWSM before it is applied to the MultilayerSwitch Feature Card (MSFC)." so I am thinking the following steps to assign VLAN 170 to firewall group first before creating SVI Interface for it
1.Remove all currently assign ie Gi 0/9 & Gi0/10 interfaces from this VLAN and then delete this VLAN.
2.Create the same SVI ie VLAN 170[IP:192.168.1.10] by this way the issue can be resolved.
As in part of my configuration PBR is define like this .
interface Vlan170
description "PUBLIC IP VLAN"
ip address 192.168.1.20. 255.255.255.0
ip policy route-map NAT
route-map NAT permit 10
match ip address 101
set ip next-hop 192.168.1.10
I need to clearify what impact it may have on PBR part if I delete and create the VLAN 170.Will the traffic move to the inside interface of FWSM.
Sometimes I need to login to server shared folder with different username and password than saved one in "manage network password" or "windows credentials" (windows 7). At that time, I have to delete the previous one in "managed network password", then open the shared folder with new username, again save the old once once it is done.Is there anyway I can just open with different usernames without deleting the saved one? Different users have different privileges in server. Similarly, how to delete temporarily network cached passwords without restarting? I tried net user * /delete but it doesn't work?
View 3 Replies View Relatedi sold off my e4200 & brought a e4500 .The e4200 has had a 2 TB W.D external drive attached ,i stream movies to a sat pvr in the .ts format .The problem is i set the e4500 up & it deleted my .ts files not once but 3 times.when i brought the e4500 i did roll the firmware back to the classic non cloud firmware.the third time i had turned the router off & once swtiched back on my files were gone .should i safely remove the drive from the set up ? what if i have a power failure?
View 5 Replies View RelatedI got one issue with the WRT610N and the NAS feature. I am running Vista on a laptop connected to the WRT610N via the 802.11n link but the issue is not here.I have a hard drive of 40GB (but same issue exist with another drive of 500GB) plug to the USB port. I can read all file without any issue. I can also add file without any problem. The problem come when I try to delete some directory. In this case I got the an 0x8007045D Error indicating that I need to have the right permission for doing this. However I do not have any issue in deleting files. In case I delete all files from a directory I can't delete the directory without the error. I map the drive to the windows explorer with the admin account which give read and write access.
View 5 Replies View RelatedIn the process of setting-up a E2500 Linksys router, I set-up my secured network which is working fine but also (I do not know how I did this??) set-up the same named network but it is unsecured. How do I delete this unsecured network.Do I need to set-up the router again?
View 4 Replies View RelatedCurrently my home network is being switched via TrendNet TEGs80G unmanaged gig switches. I have been using them for about a year now with no issues. As my home network becomes more advanced, I recently just added a Cisco ASA5505, I am thinking about swapping those unmanaged devices, 4 of them, to managed. I was looking at the Cisco SG300-10 for upstairs, and a 16 port variant for my main core. These devices do not support full Cisco IOS cli, but they are manageable with a rich feature set nonetheless. My question is, should I swap the unmanaged devices with the more expensive Cisco devices, or just keep what works and save the money until I really need to spend it. As previously stated, my home LAN works just fine as it is, however my WiFi, NTV550s, server and workstations are all on the same network. Probably not the most secure but it is what it is without VLAN support.
View 11 Replies View Relatedwhat is the purpose of the "Permint all traffic to less secure networks".
Well I know the purpose and the technique to handle some sercurity level is nice. when I cannot add add a rule without deleting this implicit rule?
The technique of security level is then obsolete?
I have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies View RelatedAll of a sudden my laptop, android phone and blu ray player (all wireless devices) can't communicate with my wired devices (marantz receiver and samsung tv). Everything still connects to the internet independently but i can't for instance play music from my wireless laptop to my wired marantz receiver. I had no trouble with this last week and didn't change anything (that I'm aware of) I did get Verizon to switch out my router but it didn't solve anything. My wife's computer also cannot connect to wired devices. Lastly, if I connect my laptop with via ethernet cable it sees wired devices fine. I tried shutting off windows firewall but didn't work. I have no other firewall/virus software installed. I can ping to all devices (wired and wireless) from my laptop.
View 1 Replies View RelatedI have installed LMS. Then I have configured Default Credentional Set. Then start discovery with cdp and arp modules. LMS found my devices, 2 of them are reachable but other unreacheble. All snmp settings on the devices are the same. I test from LMS connectivity, it works great. Then checked snmp from pc (C:Program Files (x86)CSCOpxobjectsjtin) all tools snmpset and snmp walk works corretly and can get data. How make LMS to get data from devices ?
View 4 Replies View RelatedI've added several switches and one WLC to my new NCS Prime box. I don't see them in the display. If I try to readd one, it says it already exists. What am I missing?
View 0 Replies View RelatedI got a VPN request form from one of our partners. On my side I have one ASA 5520 running 8.0(3) On their form, It says that their endpoints are two boxes, sitting on different cities, It also says that there is only one encryption domain, (actually just one IP) that I need to speficy on the VPN setting. It looks like they mean that you could access the same encryption domain from any of the two Boxes in different cities. This is strange to me, since every time I have set up VPN before, each endpoint has their own encryption domains.I never seen two enpoints with the same encryption domain behind, so Im confused wether it might be a mistake on their part, or this is expected.
View 1 Replies View RelatedLMS 3.2,the devices are not shown in the CS.
In CS Device management no devices are shown(0 devices).But devices are shown in DFM,RME and IPM.
I am trying to add some APC UPS Devices into CiscoWorks LMS 4.1. For example i have three APC Smart UPS 5000 RT RMXLI with management cards AP9619, i have chosen Device Type as "Smart-UPS RT 5000 XL" in Nom-Cisco Devices list, but when i am creating Invetory collection job, i`m getting status failed for this devices and the error is: "RICS0001:Internal Error,unable to process the collected data from the device"
View 1 Replies View RelatedI've download free trial from cisco site Cisco LMS. I've installed and now I have a question. how to add a device ?
View 10 Replies View RelatedI have LMS 4.0 server installed without any problems on windows server Enterprise edition service pack 2 then i enabled SNMP on cisco switches and routers by the following commands [code] But when i tried to discover cisco devices and after trying many times theres no result so correct commands required to be enabled on cisco devices.
View 2 Replies View RelatedWe are using LMS 4.0 with license of 100 Users. We are managing 12 devices till now. But from last two days I am trying to add a device ( i.e. 2811 router) and after adding the device in DCR (Inventry> Device Administration>Add/Import/ Manage Devices) it displays message i.e. devie added succesfully. But this added device is not displayed in Inventry> Device Administration>Add/Import/ Manage Devices.
observation :
1. In managed device list router 2811 is reflecting in Device Type Groups, but not in all devices.
2. New added device is reflecting in Known device list if we generate a report for know device ( under path Reports>Invenrty>Management Status>Known Device List).
Have a problem with LMS 4.0.1 and DFM. In DFM no of the devices leaves the questioned state. Trying to rediscover them starts a process that ends after 20% completion every time. I've put on some debuging, but that does not enable more error messages.Only thing i find is in the log file [code] As I've encoded this to be the SNMP engine ID, which on the device is. [code]
View 4 Replies View Related