Deleting Port In EtherChannel Group?

Mar 24, 2011

We have configuration of Etherchannel in Cisco 6509 connecting to Cisco 6513 switch, both running on CatOS. This is a group of 8 ports in 6509, due to some reasons one port in Etherchannel group went bad. I have disabled that bad port now. Now I have to delete that bad port from etherchannel group (First task) and add a new port to the group ( 2nd task). I have tried many cisco documents to completely delete the etherchannel port, but no use.

View 8 Replies


ADVERTISEMENT

Cisco VPN :: Deleting Group Policies In ASDM 7

Mar 14, 2013

A bit of a Catch-22 here: I am trying to delete VPN Group Policies but receive the error message that the policy is in use by a particular Connection Profile. When I try to delete the Connection Profile I receive the message that it is in use by a VPN Group Policy..
 
What else is there to delete or do I have to use the CLI?

View 2 Replies View Related

Cisco Switching/Routing :: 2960S Stacks / 3750 - EtherChannel Group Numbers?

Jan 27, 2012

I have a 3750 as core switch, adding 2 stacks of 2960S to connect. I want to establish etherchannel between the 3750 and each additonal 2960S stack, do the channel group numbers between the 3750 and the new 2960s have to match? 3750 has two channel-groups(1 and 2) already configured. Need to know,  I would create 2 additional channel groups (number 3,4) for each of the etherchannels between the 3 2960S Stacks and 3750? OR channel-group # is local to the device.

View 5 Replies View Related

Cisco WAN :: Nexus 5010 Fixed Port - Group C (17-20) Encrypted Ethernet Port

Oct 14, 2012

if I can use the encrypted port as unencrypted ethernet ports? url.. Each individual port on the Cisco Nexus 5010 switch is numbered, and groups of ports are numbered based on their function. The ports are numbered top to bottom and left to right.There are 20 to 28 ports on the Cisco Nexus 5010 switch, depending on which GEM is installed.
 
The 20 fixed ports form group 1 and are named 1/port_number. Ports 1 through 16 are unencrypted Ethernet ports. Of these, ports 1 through 8 are 10-Gigabit Ethernet and 1-Gigabit Ethernet-capable ports. Ports 17 through 20 are encryption-capable Ethernet ports.

View 1 Replies View Related

Cisco WAN :: 4006 To Setup Etherchannel Over 4 Port

Feb 18, 2011

I have a Cisco 4006 (old school) and I am trying to setup etherchannel over 4 port.  The issue I am having is flapping, it see's two IP addres on the same MAC address.  The reason for this is bonding, so all 4 ports are bonded, but I have two servers that need to send a heartbeat between the two server hence the second IP, and the other IP address to send/recieve.

View 3 Replies View Related

Cisco Switching/Routing :: 7600 Port Monitor For Etherchannel

Sep 26, 2012

on 7600 SUP720 3B.I have port channel and there are two ports on that port channel. is it possible to apply this command? does it work?

View 1 Replies View Related

Cisco Switching/Routing :: 3560 / Allowing Etherchannel Or Port Channel?

Mar 3, 2012

I am using 3560.IP rouitng is being turned off on this.Curious to know if I will create etherchannel or port channel.I think etherchannel.Correct me if I am wrong.On connecting switches I have vlan10,20,30 to be allowed.I am sure I need to allow these all vlan in 10,20,30 which are on the trunk port on each side switch.Post that will add channel-port lacp and make it in active mode.Is that correct.This way traffic will be load-balanced/aggregated on minimum 2 ports who are the part of this.

View 2 Replies View Related

Cisco :: Customizable Trunk Port Group In LMS 4.0?

Jul 19, 2011

How can I add devices onto the customizable group1?  I am trying to creat a group of trunk ports and monitor just the up/down.

View 1 Replies View Related

Cisco :: WS X6148A RJ45 ASIC / Port Group Utilization

Mar 8, 2012

Is there a way to view the utilization on a WS-X6148A-RJ-45 ASIC/port group?

View 7 Replies View Related

Cisco Routers :: RV180 - Settings For Group Of Port Services

May 27, 2012

I have two servers behind the RV180 and a list of ports I would like to open to the public (80, 443, 21, 3389).In that case, I have to setup 8 Access Rules. I am OK in the first time setting up.But later on, if I would like to change the external IP <-> internal IP mapping, I have to change the Access Rules one by one for all related ports.
 
Does it has a setting for grouping the ports together so that I can set the Access Rules by one time only ?BTW, the summary view of the Access Rules in RV180 is not very clear, I can't differentiate the Rules for different Destination NATs ... I have to click into the details one by one ...

View 1 Replies View Related

Cisco VPN :: ASA 8.4 LDAP Group To ASA Group Policy Mapping?

Jul 31, 2012

I try to map LDAP Group to ASA Group policy following documentation:
 
[URL] 
 
This is a config for ASA 8.0. I would have expected it to work on 8.4 as well but I do run into problems. The mapping as shown in LDAP Debug and ASA Log will actually happen but it is overwritten by the "GPnoAccess" Group Policy configured locally in the Tunnel Group. From earlier works with RADIUS I would have expected the user specific Attribute to be "stronger"?
ASA Log:
 
AAA retrieved user specific group policy (correct Policy) for user = XXX
AAA retrieved default group policy (GPnoAccess) for user = XXX

View 3 Replies View Related

Deleting File From One Computer To Another?

Jun 8, 2011

How do I delete a file using command prompt from one computer to another....

View 5 Replies View Related

Deleting Access Points From The Wii?

Dec 5, 2012

I would like to know how to delete a connection from my network. When I connect to the Wii it automatically chooses the right connection. What I have noticed though is that there is a third connection for a printer that is not secured and I have no idea why it is there or has an option to connect to the internet.

View 4 Replies View Related

Cisco :: LMS 4.1 Deleting Devices

Feb 14, 2012

I recently deleted some devices from LMS.  Now, when I run a device credential report, I get the following for the devices that were deleted. Device has been deleted, or is not managed by LMS.

View 1 Replies View Related

Cisco WAN :: How To Restore IOS To 2600 After Deleting It

Aug 24, 2011

I was trying to erase my lab router 2600  and reset it back to the factory defaults. Well I was able to to reset it all right but I used the erase command  which worked a little to well. So now there is no IOS and the router is in ROM mode and I didnt back up the pervious IOS "Nice". So was able to get an updated IOS for my 2600 but I'm trying to install it and don't know how. I was able to get a tftp server app for my windows pc but I'm unsure on how to configure it so I can transfer the new IOS to the router. On the up side I did learn something erasing and reset are to very different things.

View 6 Replies View Related

Servers :: Deleting Site From Google Search?

Oct 29, 2011

I have downloaded material to a site many years ago and now that site appears first when my name is typed at Google Search. The problem is that I've written many e-mails to the site manager and he is not answering. Is there any way to delete this site from my Google search?

View 2 Replies View Related

Internet Is Not Working After Deleting An Account On Computer?

Apr 27, 2013

I recently deleted an account off of my computer, it was just the account I didn't use that had no password, it was not the admin or administrator account. So I deleted it, and went to bed, I woke up the next day and my computer was just finishing installing an update, after it restarted my internet does not work and it has the yellow caution triangle over top. I troubleshooted, and got the message "windows could not automatically detect proxy settings"When I open network and sharing center it would say "identifying" forever and not identify I guess.The weird thing is, my sisters computer and my old computer can connect to the internet fine. I tried bringing my computer next to the router/modem(not sure of the difference) and i plugged the ethernet cord directly into the modem/router into my computer, and it's the same thing. The most annoying thing is that i cannot do a system restore as i have not set it up before hand.(yes i know that is a very novice mistake

View 2 Replies View Related

Deleting Items From Network Places In Windows 7

Jun 14, 2011

I am seeing old entries of phantom folders in My Network Places in Windows 7. In XP you could just delete them, but there is no selection for this in Windows 7. How to delete them?

View 9 Replies View Related

Cisco :: Deleting Whole Crypto ISAKMP Setup / Policy?

Sep 27, 2012

Just looking at a new clients setup and they have a ISAKMP vpn to the old security company I am trying to remove...I am fairly new to cisco, I actually know how to setup the ISAKMP policies, acl's etc but never had to completely remove one before All I can find is Clear Commands which seem to just flush the config not actually delete any of the policy etc...Its not that urgent as all passwords are changed on the domain and the cisco, the usernames have been deleted as well.

#show crypto isakmp peers
Peer: ** Port: 500 Local: **
Phase1 id: **
#show crypto isakmp policy
Global IKE policy

[code]...

View 3 Replies View Related

Linksys Wireless Router :: WRT610 Deleting All Files

Aug 16, 2012

I have a wrt610n that I've used for years with no problem. The usb drive I've had plugged into it has worked great for a really long time, but it's fairly small. I bought a WD 1TB hard drive, formatted it with the router set everything up. after about a day I tried to upload a file from work and got an error, and it wiped the harddrive clean. I reloaded thinking it was a fluke and everything worked fine for about a month. Uploading and downloading worked fine from where ever I was at, on the local network or over the internet. Then I tried to upload a small file, got the error and all of my files were gone again.

View 1 Replies View Related

Linksys Wireless Router :: E4200 Seems Deleting Files

Jan 14, 2013

I've got the Cisco E4200  v1 firmware 1.0.04I hooked an usb 2.0 enclosure to it running a WD red "NASware" 1TB drive to it.The drive works just fine, brand new, silent, runs cool enough. I'm not saying it's a super-drive, just not complaining of anything.I started using it as a backup drive. File disappear randomly.Gigabytes of files deleted. No power outages nothing happened, the Router is 24-7 on connected to a UPS. So it is the drive, it was never shut off since connected the drive, about a month ago. It only shares connection among a couple desktop PCs a couple laptops a network printer and a couple smartphones, all updated, all clean that is no virus or anythingI removed the drive from the router and plugged it in the computer.Files were there,even though the files in the root were not all there, it must have crashed during the last modifications, although it's bad, and it's also bad that it does not give you a single sign it has crashed.

View 4 Replies View Related

Cisco WAN :: Sup2T Not Booting After Deleting Vlan DAT File

Sep 18, 2012

We have recently purchased new Sup2T to replace the Sup720. When we tried to copy the vlan.dat file across we are facing this issue. Sup2T is not booting up once delete the  original vlan.dat file  of the Sup2T & reload.  Here is the console output during the process. What to do to get this Sup2T working.

[Code] ......

View 2 Replies View Related

Open Network Folders With Different Username / Password Without Deleting Saved One

Mar 23, 2012

Sometimes I need to login to server shared folder with different username and password than saved one in "manage network password" or "windows credentials" (windows 7). At that time, I have to delete the previous one in "managed network password", then open the shared folder with new username, again save the old once once it is done.Is there anyway I can just open with different usernames without deleting the saved one? Different users have different privileges in server. Similarly, how to delete temporarily network cached passwords without restarting? I tried net user * /delete but it doesn't work?

View 3 Replies View Related

Linksys Wireless Router :: E4500 Deleting Media Files?

Oct 2, 2012

i sold off my e4200 & brought a e4500 .The e4200 has had a 2 TB W.D external drive attached ,i stream movies to a sat pvr in the .ts format .The problem is i set the e4500 up & it deleted my .ts files not once but 3  times.when i brought the e4500 i did roll the firmware back to the classic non cloud firmware.the third time i had turned the router off & once swtiched back on my files were gone .should i safely remove the drive from the set up ? what if i have a power failure?

View 5 Replies View Related

Linksys Wireless Router :: WRT610N NAS NTFS For Deleting Directory

Mar 22, 2009

I got one issue with the WRT610N and the NAS feature. I am running Vista on a laptop connected to the WRT610N via the 802.11n link but the issue is not here.I have a hard drive of 40GB (but same issue exist with another drive of 500GB) plug to the USB port. I can read all file without any issue. I can also add file without any problem. The problem come when I try to delete some directory. In this case I got the an 0x8007045D Error indicating that I need to have the right permission for doing this. However I do not have any issue in deleting files. In case I delete all files from a directory I can't delete the directory without the error. I map the drive to the windows explorer with the admin account which give read and write access.

View 5 Replies View Related

Linksys Wireless Router :: E2500 / Deleting A Duplicate Unsecured Network?

Mar 8, 2012

In the process of setting-up a E2500 Linksys router, I set-up my secured network which is working fine but also (I do not know how I did this??) set-up the same named network but it is unsecured. How do I delete this unsecured network.Do I need to set-up the router again?

View 4 Replies View Related

Cisco :: Avoid Deleting Files From Flash (Switch 2960) No Support EEM

Apr 3, 2012

I am looking for ways to avoid deleting files from the flash in a Switch 2960, I found some scripts TCL / EEM but this switch does not support EEM (IOS c2960-lanbasek9-mz.122-58.SE2.bin).

View 13 Replies View Related

Cisco Wireless :: 5508s - Deleting Client Immediately Since WLAN Is Changed

Sep 28, 2010

I recently upgraded our 5508s to 7.0.98 I am now seeing this message on the primary WLC while running adebug on a client *apfMsConnTask_1: Sep 29 11:05:36.114: Deleting the client immediately since WLAN is changed. 

View 6 Replies View Related

Cisco Switching/Routing :: Impact Of Deleting And Creation Of SVI Interface On PBR 6513

Apr 22, 2013

I have a query regarding the deletion and creation of one of my SVI interface on 6513 ,The reason behind it as follows.My traffic get to Internet in this manner
 
proxy(external int.)[IP:192.168.1.30] --> Gi0/9[6513 in VLAN 170] --> SVI VLAN 170[IP:192.168.1.10] --> Gi0/10[In VLAN 170] -->ASR[IP:192.168.1.20],I need to assign this VLAN ie 170 to my inside interface of firewall but it was mentioned in books like this  "Assign the VLAN for the FWSM before it is applied to the MultilayerSwitch Feature Card (MSFC)." so I am thinking the following steps to assign VLAN 170 to firewall group first before creating SVI Interface for it
 
1.Remove all currently assign ie Gi 0/9 & Gi0/10 interfaces from this VLAN and then delete this VLAN.
2.Create the same SVI ie  VLAN 170[IP:192.168.1.10] by this way the issue can be resolved.
 
As in part of my configuration PBR is define like this .
 
interface Vlan170
description "PUBLIC IP VLAN"
ip address 192.168.1.20. 255.255.255.0
ip policy route-map NAT
 route-map NAT permit 10
match ip address 101
set ip next-hop 192.168.1.10
 
I need to clearify what impact it may have on PBR part if I delete and create the VLAN 170.Will the traffic move to the inside interface of FWSM.

View 0 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.3 - How To Associate Identity Group With AD Group

May 1, 2012

how to associate an AD group - which i have defined in users and identity stores/external identity stores/Active Directory/Directory attributes to associate with the relevant identity groups - Users and identity stores/identity groups Is there an example of this being done somewhere as i am having problems understanding how to do this from the user guide.All i want to do is associate identity groups with ad groups.

View 3 Replies View Related

Cisco Firewall :: ASA 5505 - Cannot Add Rule Without Deleting Implicit Rule

Jan 18, 2011

what is the purpose of the "Permint all traffic to less secure networks".
 
Well I know the purpose and the technique to handle some sercurity level is nice. when I cannot add add a rule without deleting this implicit rule?
 
The technique of security level is then obsolete?

View 8 Replies View Related

Cisco WAN :: QOS On Etherchannel In 3560?

Jan 25, 2012

I am trying to see how can configure MQC in Etherchannel. I know that i need to do this in the memeber physical interfaces of the etherchannel.The etherchannel is a trunk port allowing few VLANs. SVIs are created in the switch for this VLANs as well. tell me where i need to apply the QOS ? Is it under the member physical interfaces ?.
 
What will happen if QOS applied under the SVIs?

View 5 Replies View Related

Cisco WAN :: Etherchannel Is Down At Catalyst 6500

Oct 29, 2012

I have 2x6500s series catalyst core switch. i configurated vss. all them are working normal. but i have one problem. some of my servers link is down sometimes. I configurated server links as etherchannel.at etherchannel  not both of links down only one link down.this modules i used to connect servers to  core switch. modules 3 and 7 slot.

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved