I am trying to add some APC UPS Devices into CiscoWorks LMS 4.1. For example i have three APC Smart UPS 5000 RT RMXLI with management cards AP9619, i have chosen Device Type as "Smart-UPS RT 5000 XL" in Nom-Cisco Devices list, but when i am creating Invetory collection job, i`m getting status failed for this devices and the error is: "RICS0001:Internal Error,unable to process the collected data from the device"
View 1 RepliesI am using Cisco Works LMS 4.0 for collecting configurations of the devices. After changing the configuration of the device what is the minimum time that LMS detects the configuration was changed and save (make archive) the new configuration in the LMS database ? (Periodic Collection and Polling are disabled). Which mechanism drive this process, SNMP Trap?
View 4 Replies View RelatedCurrently my home network is being switched via TrendNet TEGs80G unmanaged gig switches. I have been using them for about a year now with no issues. As my home network becomes more advanced, I recently just added a Cisco ASA5505, I am thinking about swapping those unmanaged devices, 4 of them, to managed. I was looking at the Cisco SG300-10 for upstairs, and a 16 port variant for my main core. These devices do not support full Cisco IOS cli, but they are manageable with a rich feature set nonetheless. My question is, should I swap the unmanaged devices with the more expensive Cisco devices, or just keep what works and save the money until I really need to spend it. As previously stated, my home LAN works just fine as it is, however my WiFi, NTV550s, server and workstations are all on the same network. Probably not the most secure but it is what it is without VLAN support.
View 11 Replies View RelatedI have installed my new E4200 and it works beautifully. I have several wirelss adapters and a few wired connections through powerline adapters. I also have a second VPN router attached to the 4200.I can see the wireless connected devices with the associated IP addresses. If I plug a laptop directly into the Cisco, I can of course see it.However, I can see none of the devices attatched to the powerline devices? I have a securty cam connected via the powerline and want to know the IP address. I checked with cisco technical support via chat and they said it is impossible. I have used 2 previous routers with the same configuration and can see all devices.
View 1 Replies View Relatedthis computer was working on this router no problem. computer crashed and noiw computer is fine i connected it to my cable from ny desk top comutyer and works fine. It just cannot hook up to the wireless connection?
View 1 Replies View RelatedAll of a sudden my laptop, android phone and blu ray player (all wireless devices) can't communicate with my wired devices (marantz receiver and samsung tv). Everything still connects to the internet independently but i can't for instance play music from my wireless laptop to my wired marantz receiver. I had no trouble with this last week and didn't change anything (that I'm aware of) I did get Verizon to switch out my router but it didn't solve anything. My wife's computer also cannot connect to wired devices. Lastly, if I connect my laptop with via ethernet cable it sees wired devices fine. I tried shutting off windows firewall but didn't work. I have no other firewall/virus software installed. I can ping to all devices (wired and wireless) from my laptop.
View 1 Replies View RelatedI’ve set VPN up between two sites using Cisco ASA 5505 and Wizard. Unfortunately VPN works only one way From 8.2 (2) to 8.3 (1) and after spending one day trying to resolve the issue. Logs shows that ping leave ASA 8.3 but never hits ASA 8.2 – opposite way everything works perfectly. [code]
View 2 Replies View RelatedSM-ES3-16-P works as a layer 3 module which means that the uplink which connects to router ( Internally ) is a layer 3 interface . Is there a way we can use it as a layer 2 switch and connect the uplink as a trunk port ?
View 1 Replies View RelatedHow NetFlow works when NAT is enabled in the Cisco Router? ...the translation of IP addresses is done before or after save the packets in the flow caches?
View 3 Replies View RelatedI'm setting up a VPN in order to share files between two locations. I'm not sure it's the best solution, but he insists on using his Cisco ASA 5505 Firewall via a clientless VPN. His set-up is a simple residential cable modem (Motorola SurfBoard/TimeWarner) set in DMZ mode, the Cisco ASA, and an Ubuntu server.
The Clientless VPN is set up, as are the user groups, and bookmarks. I'm able to browse to the firewall's internal interface IP (https://192.168.1.1) and log in to the Clientless VPN portal, and from there, I can access all of the plug-ins I've configured (CIFS, VNC, etc). The problem is that I cannot connect from outside the local area network.
I think it's something very basic that I'm missing, like a NAT rule. I've tried adding some, but they always seem to interfer with the NAT rule allowing users to connect, via the internet, to the Apache web server (port 80) running on the Ubuntu machine behind the ASA Firewall.
Like I said, I'm not sure this is the best solution for him. Using an ASA seems like overkill for something that can be accomplished with some software, but he and I are both fans of Cisco, and, as I said, he is adament about using this set-up. If it comes down to it, I'd like to be able to honestly tell him that I exhausted every resource in trying to find a way to make this work for him before giving up and going to "Plan B".
I am fairly new to Cisco IOS, yet I've managed to get it up and running on a Cisco 1841 to act as a router and firewall between WAN and LAN. Everything works *except* I am unable to ping or make any other connection from the router itself to the WAN. It will ping or telnet to the LAN, all LAN to WAN traffic is functioning properly, NAT is setup and functioning, WAN to LAN and inbound firewall is working, yet I still cannot ping or telnet from the IOS interface to anything on the WAN side (I've tried using different source addresses)
I am hoping there is something obvious that I overlooked, perhaps IPS is blocking the traffic? Do I need a specific route entry for the local device? I can post entire config if necessary, but would rather not if there is an obvious solution.
We are in the process of upgrading from ACS 4.2 to 5.3. Most things seem to be working but we are having some major issues with the Rancid configuration tool. I can log into devices using CLI login with the credentials that Rancid uses but Rancid fails login.
This worked fine with our 4.2 implementation but not the 5.3. Presumably I need to make a chance in the expect scripts because the new ACS server sends a different string but I have no idea what it is supposed to be.
We have a PBR configured on a 2911 router (15.1-4.M2). The PBR is being used to send specific traffic across a S2S VPN instead of an MPLS connection. If ip cef is enabled, the router sends the traffic across the MPLS. If ip cef is disabled, the traffic goes across the S2S VPN. I checked to see if there were any bugs in the code they are running about this and nothing came up. It almost like CEF enabled PBR isn't working on this device, even though it should be enabled by default when ip cef is turned on.
View 3 Replies View RelatedWe have 80 LAP1252AG and WLC 4404. We plan to upgrade our WLC 4404 to WLC 5760 but not sure if our current APs will work with the new WLC 5760.
View 1 Replies View RelatedI have a PIX-525 with an UR license. I was trying to get my VPN to work from my iphone over the weekend but to no avail. I then changed the interface to the inside to see if my iMac could connect and bingo! It worked. I then tried to connect via inside interface with my iphone and it worked.
I connected a PIX-515e and, using the same settings, can connect to the outside interface via my iPhone.
Now, to answer the pressing questions, yes I changed the server IP address in my IPSEC client settings to reflect the outside and inside interfaces as I was testing each one. I was using a preshared secret. Yes, the secret was entered correctly and they all matched...yes, the tunnel name was entered correctly. I was using local user database for authentication with username/password (i.e. no certificate authorization to make things simpler for debugging). I changed the syslog to debugging and I see absolutely no errors when trying to connect my iphone to the outside interface (i.e. turning wifi off so I'm on my 3G data network). The only thing I see is where my iphone hits the outside interface and it does a teardown (or whatever its called) but that's it.
Why would this work like a charm with my PIX-515e and not my PIX-525? Could the VPN accelerator card in the 525 be at fault? The 515e does not have the aecellerator card. why I can esablish a VPN connection on the inside interface but not the outside?
I have Cisco works LMS 3.2. When i take manual backup, it hits following error,
ERROR(1101): Database dfmInvDb backup failed.
Validation e:/backup_newdfmdatabasedfmInv.db failed.
[Wed Sep 14 15:53:41 2011] Validation e:/backup_newdfmdatabasedfmInv.db failed Validation e:/backup_newdfmdatabasedfmInv.db failed. [Wed Sep 14 15:53:41 2011] Validation e:/backup_newdfmdatabasedfmInv.db failed.
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else.If Cisco-1921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
My provider is Time Warner and I have their Wideband 50 MBs. This requires me to have a Motorola Surfboard router/modem (so no stand alone modem)
1. No applications such as google talk, steam, my ftp client or basically any computer application that requires internet for some of its functions. (all on my desktop PC connected to LAN)
2. The internet would partially work. I could get to some websites but it would often fail to load
3. Other computers are able to connect to the LAN and it work without an issue
I can only connect to the development server when I am logged into the VPN (Cisco VPN)I do most of my work on my desktop, which is running XP sp3. While logged into the vpn there, I can reach the SVN and FTP servers fine, but I cannot connect to the development website to view anything.I also have a laptop that is running windows 7. When I connect to VPN on that, I can connect to the website just fine. It is all from within my house so using the same router / cable modem / internet service. Both have installed the latest Cisco VPN softare, and use the same profile to connect.The differences are, windows 7 vs Windows XP. Windows 7 is running Microsoft Security Essentials and XP is running Comodo.
However, even when I turn off Comodo on XP I still can't connect to the website. (Just FYI, I also have XP as dual boot on the laptop and tried connecting from it but no go). I am getting absolutely no assistance from the company I am working on, so really can't ask them anything, I guess it is something I have to figure out myself.But it is frustrating me. I prefer to work on my desktop and it is set up in with all my development tools etc in a nice environment, where the laptop is noisy and slow and not a preferred work place.
I've got a bit of a query regarding how spanning tree works on L3 switches?So say we have a few 3550's connected together and spanning tree has converged and everything is looking ok. We then introduce routing into the network, does STP still operate in the same way or is this layer 2 feature now redundant because routing has taken over?I just couldn't figure out if STP still operates at layer 2 to prevent loops and routing sits on top to route the traffic?
View 1 Replies View Relatedknow any plan from Cisco to make 300 series switch to work as a DHCP server?
View 1 Replies View RelatedI have 3 ASA's, all with the same config attaching to an 1841. One is hosted with Embarq and works fine, one with Comcast is not, the 2nd with a local cable provider is also fussy. Whats up based on the debug from the 1841? I'm getting little debug off the peer ASA from ISAKMP or IPSEC. You can carry the ASA's from one site to the next and the problem does not follow the boxes. This was working fine for several months, but now its not, and no.. the config did not change.
View 4 Replies View RelatedI wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.it is necessary to reset the table mac and other resources that are not possible via WEB GUI..I wonder if the version of Cisco AP 4410N WAP SSH works, because since I bought the equipment funciou never the same, the user is not the same as the web access and I saw no default setting for this in the cisco site.It has some important information about this topic, it is necessary to reset the table mac and other resources that are not possible via WEB GUI.
View 1 Replies View RelatedI'm very new to cisco devices but we recently acquired a catalyst 2911 device for our co-lo cabinet and I am trying to get a site-to-site vpn connection working between the facility and my offices network as well as a remote access VPN for me to use in case I have to fix something while outside of the office.
The office's gateway is 66.119.163.2 and the device is a TZ210 with it's LAN network being 192.168.1.0 /24
The co-los gateway is 204.244.50.254 and the device is an ASR 2911 with it's LAN network being 10.0.10.0 /24
The S2S VPN connection is up between the two locations and the 2911 device and the servers within it's LAN can ping and RDP to the office's machines. The office network can only ping the LAN interface IP on the 2911 which is 10.0.10.1 but not the servers in the network. the site-to-site VPN was set up with the CCP wizard.
How can I allow the 192.168.1.0/24 network to see the 10.0.10.1/24 network and why do I only currently see the gateway?
If need be I can post my running-config file with the preshare keys redacted.
We have a Cisco Works LMS 3.2 (solaris) and installing service pack 1 we get an error during installation process:[code] We attach instalation log. We think the problem can be related to bug CSCtn45425.
View 1 Replies View RelatedI have setup a remote access VPN to an ASA5505
I have a directly connected server behind the ASA and I can ping the server without a problem.
The VPN client reports packets being encrypted and decrypted
However when I try to RDP to the server the encyrpted packets keep incrementing but the decrypted packets do not.
I am also not seeing any RDP traffic hit the server (verified by ethereal)
I have done a packet tracer and it suceeds but ends with an IP spoof which I believe is correct as it is vpn traffic and not actually being encrypted.
This is the debug from the RDP session, I am confused by a Denied ICMP on line 2 as I am able to ping the server?
%ASA-6-302013: Built inbound TCP connection 88193 for external:172.16.24.4/50984 (172.16.24.4/50984) to internal:192.168.100.146/3389 (192.168.100.146/3389) (roger_ssl)
%ASA-4-313004: Denied ICMP type=0, from laddr 172.16.24.4 on interface external to 192.168.100.146: no matching session
[Code].....
The only logical bit to this is flow closed by inspection? Does this mean the server has not responded?
And the decrypt packets not increasing when trying to RDP Does this mean that I have reached the end of my ASA knowledge on this one!
I have been looking for a document that outlines the process for importing data, devices, and saved configs from CiscoWorks 4.0.1 to Prime Infrastructure 1.2. First of all is it possible? And if so, where is a document I can reference?
View 3 Replies View RelatedI have quick question here does AP BR1310 can be associated with WLC 5500?
View 4 Replies View RelatedI´m getting started on ciscoworks and i trying to configure a device discovery to start but i have some questions about how configure this tool exist 5 parameters that i have to configure to start the device discovery.
•Configuring Discovery Module Settings
#
•Configuring Seed Device Settings
[Code]....
I want to add devices that found neighbors via CDP son in the configuring discovery module setting i choice that option In the configuring seed device setting i choose DCR as seed device that means those devices already in the DCR start discovering from those devices but you can add more seed devices how i can add a seed device ? with ip addres or something like this? and this device have to be in the DCR already or not? The configuring SNMP settings, this community correspond to what device? the devices that i want to add ? and in the field target name what ip adders have to be? and if i have different community of snmp in my devices what device and snmp community have to configure in this parameter
i have a problem with a cisco 857-K9 router. We can access internet but if we ping a web server, every first ping fail but all others works...
View 15 Replies View Related We have two different entities we support and both are set up as autonomouse wireless groups. The SSID is the same though so they can use their 7921's between floors and buildings. The problem we have had is that the phones on the first floor were getting the IP's of the organization on the second floor. When you view the AP's on the phone the ap directly next to it on the first floor (the one its suppose to talk to) is listed first, The strange thing is that shows it is connected to the right AP (the first floor one). The AP on the second floor is also listed but its about third down. After the phone sits it will actually change IP's but not all of them. Their were a few phones that took about a half a day to get the correct IP.
My question is how do these phones grab their ip's? I know how DHCP works but I am needing to know specifically how the radio works on the 7921's. What is the boot up process? It appears that it must cycle through each channel starting with the highest and loop through a process in descending order: compare ssid's and then authenticate if possible. I am assuming it is seeing the second floor first because initially they all get the second floor ip. The second floor is on channel 60 and the one it should connect to is on channel 36 (We are using 802.11a). That's how I came up with my descending channel theory.
We are having problems with using QuickVPN to connect to our RV220W.Sometimes it works, and sometimes it doesn't. There doesn't seem to be any rhyme or reason to it. [code] The firmware version is 1.0.3.5.
View 1 Replies View RelatedI have a problem with may Cisco, it´s not start, only works the fan, the problem began when y turn down the Cisco and turn on again, but it´s not start. can something tell me what happen whit it.
View 1 Replies View Related