I am using Cisco Works LMS 4.0 for collecting configurations of the devices. After changing the configuration of the device what is the minimum time that LMS detects the configuration was changed and save (make archive) the new configuration in the LMS database ? (Periodic Collection and Polling are disabled). Which mechanism drive this process, SNMP Trap?
View 4 RepliesI like to know how I can save or export all of my devices configurations to an FTP server for example.Cisco Prime LMS 4.2 appliance.
View 4 Replies View RelatedI am trying to add some APC UPS Devices into CiscoWorks LMS 4.1. For example i have three APC Smart UPS 5000 RT RMXLI with management cards AP9619, i have chosen Device Type as "Smart-UPS RT 5000 XL" in Nom-Cisco Devices list, but when i am creating Invetory collection job, i`m getting status failed for this devices and the error is: "RICS0001:Internal Error,unable to process the collected data from the device"
View 1 Replies View RelatedWe running ACS 5.2.x and need to collect the below log file:
var/log/ade/ADE.log
I know this should be taken while loging to ADE/Linux root, but I'm remember how to loging as I havent created and service account (as IPS).
ACE is configured to point accounting to ACS servers but ACS servers are not seeing all the accounting logs. I can only see accounting logs from ACE for watchdog, start and stop.
View 5 Replies View Relatedvlan.dat file fetch.
I'm using Cisco Prime 4.2 and VLAN fetch for all devices is currently going over TFTP. Devices managed by LMS are 2960, 4500, 6500 series. All devices are using SSH v2. ACS server is configured on all devices and SSH credentials are OK.
This is the error message I get when i select SCP: "SCP user credentials not available. Configure the SCP user credentials and try again Action: Check if protocol is supported by device and required device package is installed."
Is it possible to use SCP as VLAN fetch protocol? How to configure this on a devices and how to enter SCP credentials in LMS?
We are using Cisco Works LMS 4.0.1. Acquisition info reports last acquisition end time 19 July and Campus data collection running. Number of host entries is 68 but we have two thousands PCs. When we try to perform an acquisition action with scope all hosts and users, we receive this message;
Failed to start acquisition: Construction of XML data required for UT is in progress.Please try after some time.
Cisco ACS 5.2 secondary server is configured as a log collector for both primary and secondary server .Now i am facing problem in log collection from primary server .ACS secondary server is not collecting any logs from primary .
View 2 Replies View RelatedMy devices configurations are not getting backed up.
View 1 Replies View Relatedhow to connect UTP cable
View 1 Replies View RelatedPlatform: LMS 3.2.1 with RME 4.3.2 on Windows 2003.I'm having a problem with several devices that were backing up fine until this week - suddenly they aren't backing up their running configurations, but RME is fetching their startup configurations fine and VTP backups are fine. At first I thought it might be timeouts, so I used inline edit to incease the telnet timeout for a device to 180s. However, the job fails well within this time period (debug shows on i/o error?). My order of protocols is SSH, Telnet, TFTP. I took a stab in the dark that this suggested a database problem so I picked one at random and deleted it from DCR, and readded it and it worked. However, for the other 48 devices affected it did not.
I'm wondering if I need to do anything to the RME database to get things back to where they were? Do I need to reinitialize the RME database, and if I do that what do I lose? [code]
I would like to have a support on AIR-AP1142N-E-K9 configurations.How I can config this AP?
View 1 Replies View RelatedI was recently given a Cisco 7200 VXR and told to erase the stored configurations in it. how to do erasing of Cisco 7200 stored config else I might have to delete them line by line.
View 4 Replies View RelatedWhat module is used to push configurations in LMS 3.2.1?
View 1 Replies View RelatedHere is my basic network layout for multicasting for Syn-apps
Multicast Source-->3750 SW (add PIM SM-DM? Yes/No)-->3845 WAN Router (add PIM SM-DM? Yes/No)-->T1-->2821 (add PIM SM-DM? Yes/No)-->3560 SW (add PIM SM-DM? Yes/No)
OK, in this is it necessary to configure "IP Multicast-routing" on the switches? Do I configure PIM on all interfaces that will handle multicasting (router and switches?) If PIM is enabled on the 3750 do I need PIM configured between the 3845 and the 2821 ? Do I configure the Auto-RP on the 3750 or the 3845 ?
i have few devices in Cisco works, when i try to view their configuration. i get this error.DCMA0011: No configurations archived for the device(s). The selected device(s) should have at least one archived version.
View 1 Replies View RelatedI have this firewall working as active/standby. Everything seemed to be ok, but we noticed that confirgurations are not being replicated by saving configuration either copy run start or write. The workaround here is write standby command. Below the configs and stats, plus the show version, which is the same in both equipments:
Header 1
failover
failover lan unit primary
[Code].....
We upgraded to Cisco LMS 4.2.1 recently and we have noticed that every time we reboot our Windows VM Server the archived configurations from the network devices are no longer displayed. They do not appear in the archive, version tree or directory. We are meeting the minimum system requirements for running LMS 4.2.1 and we do not seem to have found any possible bugs related to this.
View 8 Replies View RelatedWe have a number of 2651XM with WIC-1ADSL. These are supplied by another company and we do not have access to the configs.We are told that the maximum througput from the ADSL WIC to the FastEthernet 0/1 is 2.5Mbps ( "it's a backplane issue" ), even though the ADSL speed reported by the router on the external interface is 8MbpsT
View 3 Replies View RelatedWe are deploying over 20 RV180W Routers for a client and need to find a faster way to configure them for shipping.We have created a base image (all settings that will be shared between the 20 locations), we need an easy and quick way to make IP changes for the 3 VLANs and Local Security Groups for the IPSEC VPN.I tried to edit the CFG file by hand, but the checksum fails when it is loaded into the RV180W.How can I accomplish this? Can I manually create the checksum?Can I remove the checksum?
View 3 Replies View RelatedI have an ASA 5505 without any IPS module.While copy/pasting some configurations from another 5510 with IPS I copied my mistake the some of the IPS configurations part. Now I can't remove it.When ASA starts I get this Warning:
...WARNING> IPS policy is configured without an SSM card.
*** Output from config line 828, " ips inline fail open"
Those lines are:
policy-map Outside_Policy
class IPS_class
ips inline fail-open
When I try to do "no ips inline fail-open" I get an "invalid input detected".If I try a no class IPS_class I get that is being in use.What can I do to clean up those lines?
I'm trying to move some configurations over to an ASA5510 and some of the commands are a bit different than I'm used to (worked on old pix before)
I've configured the following on the device:
Outside interface: 65.66.64.34/28
DMZ : 65.66.64.49/28
Inside : 10.2.3.3/26
===========================
The current firewall has the below configured on it (old Juniper)
10.2.3.0/24 gateway 10.2.3.15 **10.2.3.15 is the IP for 3750 switch on the inside LAN**
10.0.0.0/24 gateway 10.2.3.4 **10.12.175.4 internal vpn- will remove later but thats a different discussion**
0 0 gateway 65.66.64.33 **to internet
10.0.1.0 gateway 10.2.3.2 **10.2.3.2 represents mpls traffic
[code]...
The current set up for this network has an mpls router and a vpn concentrator as part of the network my aim currently is to replace the juniper with an asa5510 the changing of the vpn tunnels will be for a different time:
work station ===> switch (3750) DG to =====> MPLS (vendor owned and managed) ====> non mpls traffic ====> vpn concentrator ===>firewall ===> router
The above will need acls to go with the routes, which I should manage ok just want to make sure the routing is configured properly
I have an issue with the LMS 4.0, i added manually the ASA Fws 5520 and 5510, and i see them there, but i cannot see the configuration, inventory and technology details.Telnet is deactivaved in ASA´s, ssh and snmp v3 are enabled.Routers and switches were added without issues.
View 3 Replies View RelatedI have a Domain Controller on windows 2003 advanced server. and I have roles and some configuration such as rights, user accounts, DHCP configuration, DNS server and etc on it.Some times windows needs to be reinstalled but after reinstalling,configuration of roles would be lost. I don't know how can I backup these settings? Is there any solution about this problem.I know a simple way is creating an image of windows installation drive by an application such as Norton Ghost but I'm talking about windows solution.
View 3 Replies View RelatedMy friend recently let me have his Seimens Gigaset SE567 modem which i needed cause it has a router but as soon as i switched it with my old router which is a Westell 6100f,the internet light wont show up ..so i contacted verizon and they said that there service is plug and play type of service so i am lost on what to do ..i looked around the forums and i got close by going to the browser and typing the IP but from there i am stuck ..i don't know how to set up any thing in the configurations.
View 2 Replies View Relatedsetting two network, I try but the other other network is so slow and a lot of time will not connect to the net
View 1 Replies View RelatedHas anyone implemented a working Nat on a Stick?I am looking for 3750 configurations for Nat on a stick.Our users need to access the camera monitoring from home as well as in work.We will like to setup the monitoring software with public address (and port) of the cameras, as the users use the same configuration at home and work.DNS will not work for us as the monitoring settings only accept IP.
View 4 Replies View RelatedI built a VSS pair with a couple of 6509's. This was our first pair so we took the opportunity to do some testing. One of the features we tested was the priority/preemption feature, which we decided not to use. After some time we shutdown switch 1 and relocated it to another building. Unfortunately, because of a lack of fiber, it was not connected to switch 2 for several months. Also, unfortunately, I failed to remove the priority commands. Now while switch 1 was "unconnected", we made changes to the config on switch 2. Months later, when the fiber was complete and I connected switch 1, preemption caused it to take over. I'm guessing switch 1 thought it's config file was the better one, and proceeded to overwrite switch 2's production config. I quickly disconnected the fiber but not before losing my production config on switch 2. We of course recovered from that with a backup, but now I need to connect switch 1 again. I have removed the priority command from switch 1 and rebooted it.
View 7 Replies View RelatedI have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in.
View 1 Replies View Related I have one ASA5520 with version 8.4(3), and a few ACL rules defined. One ACL is permit traffic from one interface(EXT_SERVICE) to another interface(DMZ_SERVICE), if i change that rule to deny traffic, all new connections that match the rule is denied, but no the established connectios. ¿Why the established connections can pass the deny rule? ¿How I can change that? I need create a ACL with deny type and stop all comunications that is running and match the deny rule.
Running-config of my ASA5520:
ciscoasa# show run
: Saved
:
ASA Version 8.4(3)
!
hostname ciscoasa
enable password 8ay2wjIyt7RRXU24 encrypted passwd 2wFQnbNIdI.2KYtU encrypted names !
interface GigabitEthernet0/0
[Code] ........
I have issues with port forwarding. I did, but it didn't work. Then I tried different ip addresses. Now I don't know how to delete those configurations, because when I try to overwrite it says already exist. And still port forwarding is not working. I did: ip nat inside source static tcp (ip and port numbers)Our device is 1841, also we have firewall within this router. DHCP is in our 3750.
View 9 Replies View RelatedI have bought 2504 LAN Controller and my old 1142 wants to configure to accept that Controller instead of old controller. These APs and controllers in far away site and before I go there I want to figure out how can I do following.
1. How can I configure old 1142(Previously connected with another LAN Controller) to accept New 2504 Controller instead of old controller ?
2. What are the concerns do I need to consider?
We use Cisco LMS Prime 4.1 to archive our Cisco Equipment configurations.
Now we want to store the configurations off site.