Cisco Wireless :: AIR-LAP1262N-A-K9 Not Initiating Join Process?
Sep 11, 2012
I foolishly put this 1262 into Bridge mode. The AP didn't accept that.
It had been joined to a 5508 running 7.2.110.0 and was running fine.
I've loaded on ap3g1-rcvk9w8-tar.124-23c.JA5.tar using the archive download-sw /overwrite /force-reload tftp://10.192.175.119//ap3g1-rcvk9w8-tar.124-23c.JA5.tar command.
When the AP reboots it has retained it's hostname from its CAPWAP days and indicates it is in DISCOVERY: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY.
It gets a DHCP IP but never tries to find a controller. DNS on the subnet resolves CISCO-CAPWAP-CONTROLLER (& lwapp) to the 5508 mentioned above. I use this port for priming all my APs.
Are there other residual files in nvram: or flash: I need to remove? Is this thing now just a fancy paperweight?
View 4 Replies
ADVERTISEMENT
Sep 13, 2012
I believe I know the answer to this question already but I just wanted to make sure. Is it possible to connect a LAP access point directly to WCS without using a WLC? WCS is just for management and reporting and does not act as a WLC.
View 2 Replies
View Related
Mar 2, 2013
Just wanted to confirm if the above AP and antenna are compatible. I was trying to configure them on the Cisco configurator, but I couldnt find it as an option for the 1262AP.
View 7 Replies
View Related
Sep 12, 2012
I am trying to configure this newly purchased AP to be used for WiFi surveys, heatmaps, etc..
I cant seem to get to the web interface of the AP to make config changes, even though it is picking up an IP via DHCP and it is pingable.
View 2 Replies
View Related
May 19, 2012
i have 1262 LAP which is fail to boot and went to rommon mode
here are the logs
ap: boot
Loading ""...: permission denied
Error loading ""
[Code].....
View 5 Replies
View Related
Mar 11, 2012
I have a new deployment with a Cisco 5508-50 controller running 7.0.220.0 code and 35 AIR-LAP1262N-A-K9 access points. Current legacy clients have trouble connecting and after connecting they may or may not drop off and have trouble connecting again.
View 16 Replies
View Related
Sep 26, 2012
We have an ASA5510 with AnyConnect SSLVPN set up, which works great from remote locations. However, when I am inside the network, I cannot connect to this SSLVPN. I would like to be able to this for testing purposes; I have a VLAN10 that has ACLs so it cannot reach any private IP addresses, we use this VLAN for our guest Wifi network. I would like to be able to make AnyConnect SSLVPN connections from this VLAN, to test the VPN access without having to be at a remote site. However, since I don't want to change any settings compared to my remote site, I don't want to just bind the sslvpn to both outside and VLAN10 (by issuing the enable VLAN10 statement). [code]
View 3 Replies
View Related
Oct 9, 2012
I have two core switches - 4506E, and i noticed there are frequent cpu spikes on both of the cores switches. As its spikes intermitendly i couldnt able to anlyze the issue. I need inputs on the following,
1) Is there any Free CPU process monitoring tools to identify which process is spiking ?
2) Troubleshooting techniques to identify the issue.
View 1 Replies
View Related
May 2, 2013
why my AIR-AP1262N-A-K9 will not boot all the way. It will get all the way to initiating the interfaces and stop. I can never get to controlling the cli. This is my first time with a cisco ap but from everything that I read it seamed very easy.
This unit from what I understand will work all on its own with no controller. Hence it is called a "standalone" model. Yet it seems to be looking for something to finish during the boot. Below is the out put during boot. The last line is where it stops.
r WRDTR,CLKTR: 0x8200083f 0x40000000r RQDC ,RFDC : 0x80000033 0x00000212
using eeprom values
WRDTR,CLKTR: 0x8200083f 0x40000000RQDC ,RFDC : 0x80000033 0x00000212
[Code]......
View 7 Replies
View Related
Dec 4, 2012
I'm trying to do some basic troubleshooting on our WiSMS. Some clients on a working network are unable to connect in the afternoons, debugging the client on the wism shows this message:
*apfMsConnTask_2: Dec 05 14:23:44.018: Association request from the P2P Client Process P2P Ie and Upadte CB
It keeps repeating with the Task_X changing.What does that mean?We have two controllers in our 6500's running this software ver. 7.3.101.0
View 9 Replies
View Related
Mar 15, 2012
According to the documentation, I'm supposed to be hitting the Esc key when I see the Loading "flash:/[imagename]" ####### ... line, but this doesn't seem to be working. I've tried hitting the Esc key a lot during those lines, holding it down, hitting it early, hitting it late, hitting it in the middle, and still no joy.
I'm trying to break into a handful of malfunctioning 1242AG APs to see if I can get them working, or if they're faulting hardware that's beyond repair. (So far they're all coming back with: no "IP_ADDR" variable set, so how to set that without breaking out of the boot cycle).
View 4 Replies
View Related
Mar 7, 2013
I have a wireless network infrastructure that is controlled by two WLC 5508s, Prime NCS and ISE. I have two networks for my users, an employee network and a student network. I started publishing the information for these networks via a group policy and the settings are identical, with the exception to the SSID.
My employees can logon to the employee network with no problems. I can walk up to any laptop, regardless if I have logged on to it before or not, and logon with no issues. ISE correctly profiles my account and authorizes me for the right profile. My students however are another story. Laptops that are designated for student use have the wireless network in their network list, and at the logon it shows that it will attempt to connect to the STUDENTS network. When I enter in a student username and password, it begins to login but then gives an error that says:
'There are currently no logon servers available to process the logon request'
The students cannot login at all. I can use my domain admin or my account and login to one of the units with no problem, even if I haven't logged onto the unit before with that account.
I don't know if this is an ISE issue or some other type of issue. I'm leaning towards ISE being the issue, since its what is passing authentication through to the domain. I have my students all in groups and I have those groups added to ISE, just like I have my employees added.
View 2 Replies
View Related
Mar 27, 2011
I plan on replacing my linksys BEFW11S4 wireless router with a new linksys WRT120N wireless router. Should I completely remove and unplug the old router before inserting the startup CD and beginning the installation process for the new router?
View 3 Replies
View Related
Dec 9, 2012
i have a problem with 1552E to register with 5508 WLC, and always got "AAA authentication error” in the WLC log, while AAA is not enabled. so my question is , do i need to add the MAC address to the WLC MAC filter list even if i not enable the AAA server in the WLC.
View 9 Replies
View Related
May 16, 2013
I am new to Cisco wireless solution and would like to ask how to add the AP to the WLC properly. All Cisco 1041 and Cisco 2500 WLC are new. I connect those AP and WLC to the switch without any VLAN tag and the AP can gain the IP address from our DHCP correctly. However, the AP 1041 could not join the WLC successfully.
WLC: Cisco 2500
IP Address: 192.168.1.225
version: 7.4.100.0
View 5 Replies
View Related
Mar 24, 2013
Our offcie use WLC2100 Series controller with AIR-LAP1031 and successfully join and running. Now i am trying to replace one ap with AIR-LAP1041N and join with WLC, but i can't and below the error message generate:
[code]....
View 2 Replies
View Related
Jul 10, 2012
I am trying to set up a Wireless network a WLC hosted on an SRE module in a 2911 router. I think i have most of my bases covered but there is still one problem.
My LAP1131AG AP's won't join the controller, on the AP im am seeing this:
Translating "CISCO-LWAPP-CONTROLLER.test.local"...domain server (192.168.250.10) [OK]
[Code].....
But to my knowledge an LWAP AP schould be able to join a CAPWAP WLC
View 2 Replies
View Related
Apr 8, 2012
WLC software 7.2.103.0
1. first problem: AP1252 can´t join on WLC. MAC was add on mac filter properly.
170Mon Apr 9 15:37:32 2012Mesh Node '2c:3f:38:be:53:ef' failed to join controller, MAC address not in MAC filter list.171Mon Apr 9 15:37:32 2012AAA Authentication Failure for UserName:2c3f38be53e0 User Type: WLAN USER172Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 40:a6:d9:ef:87:68 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 46 7 5 4 2 1 0 0 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0173Mon Apr 9 15:37:32 2012Coverage hole pre alarm for client[1] 8c:7b:9d:05:a0:67 on 802.11b/g interface of AP 2c:3f:38:bf:0c:80 (AP2c3f.38bf.0c80). Hist: 50 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0174Mon Apr 9 15:37:30
[code]....
Several APs can´t join on WLC and all are added on MAC filter, but they are showing this messages.
2 . Second problem.: Operational Status = UNKNOWN
Some Access Point are in UNKNOWN status. I tried but I can´t do the reboot. I can access Web config the APs using WLC, but when I applied the reset, it wasn´t working properly.
View 2 Replies
View Related
Jun 10, 2013
I'm new in installing WIFI, I have WLC 2504 using 7.4.100.0. I have AP 1600 (AIR-CAP1602E-E-K9)
I installed the WLC and AP in a cisco poe switch, wlc and ap are in the same subnet and can ping ap from WLC, but the AP cannot join the wlc. i have this error message
(Cisco Controller) >show ap join stats detailed 00:06:f6:d6:03:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
View 15 Replies
View Related
Jan 31, 2013
I have converted ap 1131 from autonomous to lwapp successfully by using upgrade utility tool but the AP does not join the WLC 2106. I can see it as a neighbor on the switch with no IP address.
View 19 Replies
View Related
Jun 29, 2011
My WLC running 6.0.182.0 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).
I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!
View 4 Replies
View Related
Jan 24, 2011
I have a 4400 WLC for 100APs running the 7.0.98.0software version. Now, only 48 APs are joined, and the WLC dont accept new joins. The log below are from my WLC but appear for all others APs:
%LOG-6-Q_IND: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%LWAPP-6-CAPWAP_SUPP_VER: spam_lrad.c:1440 Discarding discovery request in LWAPP from AP 00:3a:98:ae:e3:f0 supporting CAPWAP%CAPWAP-3-TX_ERR: capwap_ac_sm.c:1966 Failed to transmit discovery response to AP 00:3a:98:ae:e3:f0%CAPWAP-3-ENCODE_ERR: capwap_ac_sm.c:2269 Failed to encode Discovery (code)
View 2 Replies
View Related
Jun 7, 2012
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
View 12 Replies
View Related
Mar 12, 2013
I have a problem in join my ap1130ag in my wlc 2504 i activate dhcp internel (172.19.1.50 ----> 172.19.1.60) in wlc and this wlc affected address for ap1130ag (172.19.1.51) wlc and ap1130ag is connected with switch 2960 (port 17,18) this port the switche is configured in trunk mod allowed all vlan then my wlc not detected ap1130ag?
View 4 Replies
View Related
May 20, 2013
i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
View 3 Replies
View Related
Jan 16, 2013
I have some LAP1242 which by mistake were bought for Mesh. I am trying to convert them to LWAPP so what I did first was to convert them to Stand Alone then to LWAPP but I cannot get the AP to join the WLC and sends several error logs.
I attached some logs taken from AP and WLC so that you can figure out what's going on.
I wonder if I have to remove anything from flash either on SA or LWAPP mode (I know that in some cases you have to delete privete-config in order to avoid the AP taken previous configurations). By the way I think I had never seen this c1240-k9w8-mx.124-25e.JA2 on an AP IOS before, I wonder if it has to do with the mesh thing.
View 27 Replies
View Related
Apr 1, 2012
I have a cisco AIR-LAP1262N-A-K9 and AIR-LAP1142N-A-K9, and i would like to join to Cisco WLC2106 (software version 7.0.98.0)My ap 1262N have 3 antennas externals with 7dbi of ganancy,Is possible to do it?
View 1 Replies
View Related
May 23, 2013
I have WLC 2504 and AP3502I . AP can not join wireless controller .
*May 24 16:33:51.871: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*May 24 16:33:51.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.80.90.99 peer_port: 5246
[code].....
View 9 Replies
View Related
Mar 16, 2013
I have a cisco 5508 WLC and 40 cisco 360021 APs.I configured the WLC and assign the management interface IP and also configured a DHCP pool on my Cisco 4507 core switch wit option 43.But the problem that the APs connot join the WLC.
View 31 Replies
View Related
Apr 2, 2013
I'd WLC 2100 series and 9 access point LAP1142N .8 LAP1142N can work fine and join a capwap controller is ok but only one LAP1142 is can not . Part of LAP is AIR-LAP1142N-A-K9
Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: spamResolveStaticGateway - gateway found
*Apr 2 10:52:42.284: LWAPP_CLIENT_EVENT: Dropping discovery in LWAPP. This AP model is not supported by LWAPP WLC.
*Apr 2 10:52:42.284: status of voice_diag_test from WLC is false
*Apr 2 10:52:52.284: %CAPWAP-3-ERRORLOG: Go join a capwap controller
[code]....
View 4 Replies
View Related
Jun 6, 2012
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL]
Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
View 3 Replies
View Related
May 6, 2013
I have configured a 1552, that is wired to network, as "Bridge" then "RootAP".
After reboot, I can see a MAP trying to join the network, in the "simple" logs of the controller :
"Mon May 6 17:29:43 2013 Mesh Node '04:da:d2:1f:4d:6f' failed to join controller, MAC address not in MAC filter list."
As I have done for the RAP, I enter this MAC address in the MAC Filtering area under Security tab. But this action doesn't solve the problem, I continue to see this message in the controller logs !
If I open a SSH session on the RAP, I can see this block of debug messages repeat all the time :
*May 6 15:29:33.163: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 dot1x control
*May 6 15:29:33.167: %LINK-6-UPDOWN: Interface Virtual-Dot11Radio0, changed state to up
*May 6 15:29:34.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Dot11Radio0, changed state to up
*May 6 15:29:43.223: %MESH-6-LINK_UPDOWN: Mesh station 04da.d21f.4d6f link Down
*May 6 15:29:43.423: %MESH-6-ADJ_VIDB_LINK: Mesh neighbor 04da.d21f.4d6f VIDB Virtual-Dot11Radio0 going
When I take a look into detailled debug messages of the controller I can see this :
*spamReceiveTask: May 06 17:30:44.364: #LWAPP-6-RADIUS_AUTHORIZATION: spam_radius.c:242 The system could not send join reply, AP authorization failed; AP:04:da:d2:1f:4d:6f
I don't know why the system talks about dot1x or Radius Authorization, and if this is the source of my problems. On a other hand, I can see in the debug messages that there is a 2 hours lag time between controller (correct time) and RAP (incorrect, I suppose it synchronize with the controller?)
View 25 Replies
View Related
Jul 7, 2011
I setup a mini wireless LAN network lab with a not for resale 2106 wireless lan controller and a sales air-lap1242ag access point. I do not have a DHCP and DNS in my lab environment. I have configured the WLC with the basic configuration using the CLI wizard, i also configured the WLC as a DHCP server for clients that will be connecting to the APs associated to the controller.
I powered up the AP and connect the ethernet port directly to the controller, the controller issued an IP address to the AP, the AP downloaded a new operating system from the controller but failed to join the controller.
I check both debug message on the controller console and the trap messages on the controller's GUI and it say the AP could not download a configuration from the controller and it is beacuse of invalid license. Below is the trap message:
Configuration Phase Statistics Requests ReceivedResponses SentUnsuccessful Request ProcessedReason For Last Unsuccessful AttemptLast Successful Attempt TimeLast Unsuccessful Attempt TimeLast Error SummaryLast AP Message Decryption FailureLast AP Connection FailureLast Error Occurred Last Error Occurred ReasonLast Join Error Timestamp
Also, I tried to log into the GUI of the AP using the both the username and password ''Cisco'' but I cannot get into the device. I can only get in through the CLI. In the CLI, almost all the commands I enter gives an error the it is disabled. I don't know what to do any more, I want to know if the access point is faulty or i am not doing the right thing.
View 4 Replies
View Related
