Just wanted to confirm if the above AP and antenna are compatible. I was trying to configure them on the Cisco configurator, but I couldnt find it as an option for the 1262AP.
View 7 RepliesI believe I know the answer to this question already but I just wanted to make sure. Is it possible to connect a LAP access point directly to WCS without using a WLC? WCS is just for management and reporting and does not act as a WLC.
View 2 Replies View RelatedI am trying to configure this newly purchased AP to be used for WiFi surveys, heatmaps, etc..
I cant seem to get to the web interface of the AP to make config changes, even though it is picking up an IP via DHCP and it is pingable.
i have 1262 LAP which is fail to boot and went to rommon mode
here are the logs
ap: boot
Loading ""...: permission denied
Error loading ""
[Code].....
I foolishly put this 1262 into Bridge mode. The AP didn't accept that.
It had been joined to a 5508 running 7.2.110.0 and was running fine.
I've loaded on ap3g1-rcvk9w8-tar.124-23c.JA5.tar using the archive download-sw /overwrite /force-reload tftp://10.192.175.119//ap3g1-rcvk9w8-tar.124-23c.JA5.tar command.
When the AP reboots it has retained it's hostname from its CAPWAP days and indicates it is in DISCOVERY: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY.
It gets a DHCP IP but never tries to find a controller. DNS on the subnet resolves CISCO-CAPWAP-CONTROLLER (& lwapp) to the 5508 mentioned above. I use this port for priming all my APs.
Are there other residual files in nvram: or flash: I need to remove? Is this thing now just a fancy paperweight?
I have a new deployment with a Cisco 5508-50 controller running 7.0.220.0 code and 35 AIR-LAP1262N-A-K9 access points. Current legacy clients have trouble connecting and after connecting they may or may not drop off and have trouble connecting again.
View 16 Replies View RelatedIs there any chance the Wireless Repeater mode work with WPA2-AES ?If not, which model of AP should I buy to connect it with my wap54g as Wireless Repeater?
View 4 Replies View RelatedI'm trying to set up my DIR-655 so I can use VPN to access my work PC. How can I set this up?
View 2 Replies View RelatedI have a DIR-655 B1 router. The firmware is 2.00 NA. Just to clarify, the DSi itself does work with WPA, but the games only work with WEP. I made a guest account and set it to WEP and it still does not work. I have tried making the main connection WEP as well, but when I go on the game and try it, it says it is WPA and not WEP. My friend has a DIR-655 as well, but the hardware and firmware version are different. Her games work flawlessly.
View 10 Replies View RelatedDoes aps work with Wcs ?? .
View 4 Replies View RelatedI purchased 3 of these Wireless-G access points and none of them are plug and play. I am here because I have spent the last three hours trying to go through every step they suggest in the Quick Start Guide.
I tried entering in a web browser the default IP address and wait for a login that does not appear.
I've been asked to configure an 881 with a Verizon 3G backup connection as a backup to the FE4 primary WAN connection. I've been unable to get any connectivity through 3G, and in most cases, as soon as I try to configure 3G, I lose connectivity through FE4.Currently, I don't even have FE4 connected. I'm just trying to get the 3G connection working, so then I can take it back to the office and have a functional 3G backup connection. [code]
View 1 Replies View RelatedHave a Fujitsu Siemens Esprimo P2430 PC and am trying to connect it to my Virgin Media super Hub via a Netgear WN1111 USB 2.0 AdapterWireless-N. Software is loaded perfectly fine and signal is excellent but it refuses to load any web pages unless I refresh a zillion times. Internet works excellently on my laptop so am stumped. No connection malfunction is diagnosed
View 8 Replies View RelatedI want to get wifi for my laptop and ipod at work, i cannot add a router to the system lol not a option. Is there a thing i can plug into the dekstop here so i can get the internet off of it? There has to be somthing out there that can do this. Because these computers are wired.
View 7 Replies View RelatedI bought cisco AP (air-ap1142-e-k9) and we know this ap works with 802.11a/g/n same the description note on the package cartoon but my problem is when i configure that ap its work only with 802.11a/g i tries to make it works with 802.11n but fail .
View 3 Replies View RelatedI currently have a UC540 system with 12x aironet 1130 APs. Seamless roaming does not seem to work, and the recommendation seems to be to introduce a WLAN controller.
View 4 Replies View RelatedThe story is that we recently upgraded our 4404 controller to the new 7.2.0.230 code. This upgrade was from 4.2.209 code. I would like to make the change to the Multicast setup so that It is multcasted and not unicasted.So I went into the controller and selected MULTICAST for AP multicast mode and entered in a multicast ip of 239.255.1.60 ( default choosen in the cisco howto's)I then test the reason for enabling the multicast and it doesnt work. The problem is that the Wireless HP printers setup to use Apples IPRINT are not able to be found. However, when I select the Multicast setting for the APs to be UNICAST the Ipads can find the Printers and print to them.What am I doing wrong with this Multicast setting? Do i need to add a Multicast address to the router?
View 2 Replies View RelatedI recently attempted to update my access points Software from AP541N-K9_1.8(0) to AP541N-K9_1.9(2). As soon as the update and reboot were complete I could no longer connect to the wireless network using my iphone. I switched back to the secondary 1.8 software and could immediately reconnect my iphone to the network. Upgrading to 1.9(2) changes a setting or is flawed.
View 1 Replies View RelatedApple TV doesn't work over WiFi provided by WLC installed on ISM-SRE-300 module.
Apple TV server and iPad are situated in one L3 segment, Ipad can ping Apple TV
WLC and 2911 router are configured according to this docURL
Router 2911
Version 15.2(2)T
WLC
7.0.230.0
Vlan 1 and vlan 50 (for clients) are configured on 2911 router.
we do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version 6.0.188.0.AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with them.However AIR-LAP1242G-E-K9s do not, there is a problem with establishing CAPWAP tunnel with the controller.The AP is seen on the controller for a while, with 0 time up-time, cannot change any settings on the AP via controller, and after a while it disapears from the controller, apears again and this repeats.
The APs and controllers are connected to the LAN campus.Controllers via two 1G links configured as Etherchannel to WS-C6506-E VSS switch with s72033-ipservicesk9_wan-z.122-33.SXI1.bin on it.APs to WS-C3750G-48PS with c3750-ipbasek9-mz.122-50.SE2.bin on it. 3750 is connected to the C6505 via two 1G links configured as Etherchannel.Below I copied the log I captured on 1242 and the controller. Highlighted ones are the ones which I think might bring a clue.
I performed some troubleshooting steps.
- As we have some other controllers available over WAN, I tested the 1242 AP with 2100, 4400 and also with the same model AIR-CT5508-K9 with SW version 6.0.188.0 over WAN and this worked always okay.
- I wanted to be sure that I eliminate any kind of out of sequence packet issue, so I brought down all redundancy L2 links so that the L2 path from the AP to the controller was only through one leg links.
- I also brought the second controller down to eliminate potential issue with having two of them up.
- The AP gets its IP from DHCP configured on the C6506 switch, I am always able to ssh to AP, so the IP connectivity does not seem to be an issue.
- I have more 1242s, all behave in the same way. I also connected them to some other 3750 switches we have in the campus, always the same.
- As this seems to be maybe a kind of ssl issue, I tried to play with controller settings, like enabling Accept... options under Security/AP Policy,but this did not work.
- I also tried to reboot the controller, no improvement.
- The APs came from the factory, so in the beginning everything was factory default in them. They were always able to download the image from the controller in the very initial phase. I still do have some of them untouched, so I can perform any troubleshooting steps with the fresh one.I can reproduce this, can also send debugging logs if needed.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
This Discussion has been converted into document:- [URL]
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
AIR-LAP1242G-E-K9 10.0.13.28 log
*Mar 1 00:00:05.922: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.536: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot1 1Radio 0
*Mar 1 00:00:07.672: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 304 messages)
[code]....
will the AP 541N work without cluster if i purchase one AP.Does it support the bridge mode?
View 4 Replies View RelatedIf WPA-PSK TKIP or AES encryption is enabled, my Spectec SDW-821 SDIO wlan card can not connect to the WAP4410N (h/w "WAP4410N-E V02", f/w 2.0.2.1). If security is off or set to WEP 128 bits (due to Cisco's support), connection succeeds
The card worked well with my previous AP Netgear ME-102 (in WEP 128 bits mode) and DLink DWL-G700AP (in WPA PSK TKIP mode).
The AP is not faulty since the other laptops connect successfully, only my pocket PC with the SDIO card fails
I know officeextend 600 is for home user. But i wanted to know is it possible for office extend 600 to work in same subnet/vlan of WLC.
View 5 Replies View Relatedmy Wi-Fi does not connect although I can reach the internet with cable!
View 2 Replies View Relatedi am trying to change my internrt setting on my tv from my wii
View 2 Replies View RelatedI can't connect through wireless to my local anything router, NAS, printers. All the other computers can connect wirelessly with no problems. so I know that the wireless on the router is good. funny thin is that I can connect to LAN through the wired port on the laptop. Its a new laptop running windows 7 everything worked good until about 2 weeks ago. I must have changed something not sure whats up. I updated the driver on the wireless still no change. [code]
View 14 Replies View Relatedso i was having problems with my comp and re installed windows 7. Afterwards when i tried to plug in my Dlink USB wireless connection it would attempt to install it then fail. I tried putting in the disc it came with and it failed to download the driver successfully as well.
View 1 Replies View RelatedI have a ELITERGROUP V2 premeir Model 400 note book.I used my XP PRO to reinstall my LP, and now I can not get my wireless network to work.
View 4 Replies View RelatedI recently purchased a wireless extender to use on my PC, PS3, and kindle since I have such a low signal in my bedroom. I connected the extender to the PS3 and kindle with no problems. Great signal. Increased from 1 bar to 3 bars. However I can't connect either one of my PCs to it. It connects but says no internet access.
View 9 Replies View RelatedI have wonder that my laptop has wireless, and when i connect it to router to use internet it show wireless now is connect, but when i open the website it show not work..and this problem occur only my computer. and when the other computer laptop they can connect and use internet normal...
View 1 Replies View RelatedI have a E4200 router and I was using it with a 1st generation MacBook Air for internet and also had my Samsung laser printer hooked up (USB) for wireless printing. It worked perfectly. Now I have upgraded to a new MacBook Air. The internet connection works fine, but printing won't work. Same printer. Same connections.
Do I need to refresh/reboot something? My new Mac has the printer driver. I get a message "printer if offline" "printer is not connected" -I feel like the router now does not recognize the new Mac's command to print.The older macbook air still works and prints wirelessly. The new one does not.
I'm having a problem with a D-Link DCS932L camera after setting up the EA4500. The manual for the camera can be found here.
[URL]
It worked fine with my old D-Link router. Everything else in the house has not had a problem with the EA4500. There is a certail level of criticality around this camera and, if I can't get it to work, I will have to return the router. I setup port forwarding as 5556 ~ 5559, TCP Protocol (but I tried "Both" as well" with the IP address of the camera. It still doesn't work.I'm IT by trade but not in networking, i.e. I'm not stupid with tech but port wrangling is out of my comfort zone. The setup of this camera with our old router took minutes. I've spent about five hours trying to get it to work on the EA4500.
I have installed WiSM2 with ver 7.4 and Bonjour works great with instruction provided, But…… 2 problems. I cant get it to work on the same subnet. (odd since the whole problem was not able to work across subnets), More important the new Code function / password function on the airplay wont work. I get the code on the projector, but the ipad never pop up the login box it just errors out.
View 2 Replies View Related