Cisco Wireless :: LAP AIR-LAP1131G-E-K9 Can't Connect To Controller
Feb 25, 2013
I have a problem with AIR-LAP1131G-E-K9 (Boot version 12.3.8.0) access point. It can't connect to controller (WLC on SRE v.7.0.240.0) with error: *spamReceiveTask: Feb 26 07:32:31.197: %LWAPP-3-PAYLOAD_MISSING: spam_lrad.c:5516 Join request does not contain BOARD_DATA payload. do i need to do something manually with this access points? I have 10 AIR-CAP3502I-R-K9, and they are working fine with controller.
View 26 Replies
ADVERTISEMENT
Dec 20, 2009
AP = AIR-LAP1131G-E-K9
WLC = WS-C3750G-24WS-S25
Total 6 floors building, 2AP on each floor.Problem Statement:- Eg: Wireless Clients from ground floor are associating with AP on the 3rd floor.This happens throughout the whole building.I would expect that ground floor clients would be connected to ground floor AP.Is there a way to force clients on specific floors to connect to their designated floor APs?A thorough check indicate that, ground floor AP is not congested and only a few clients are connected to it.
View 11 Replies
View Related
Apr 9, 2012
The Samsung SCH-i569 Wi-Fi can't work at the LAP1131G with WiSM. It can associate to AP and get the ip address but about one minutes ago it had deauthentication and the phone's Wi-Fi status will show scanning. The phone can work at the Autonoumous mode or other 3rd party Fat AP.
View 1 Replies
View Related
May 6, 2013
i received access point types AIR-LAP1252AG-E-K9, which i want to connect to my wlan controller AIR-CT5508-K9. Update from IOS etc. is working fine. Also all access points are recognized by the controller.We got the AIR-LAP1252AG-E-K9 with two antenna versions.
View 1 Replies
View Related
Aug 5, 2012
i have lwapp 1130 in internal network , i already configure dhcp with option 43, in my switch connected to ap i set vlan 1424 for management AP and the ap got ip addres from dhcp server. The wlc controller is in DMZ with ip 10.222.5.3, from switch connected to ap i can ping 10.222.5.3 , it aslo seperated by cisco asa firewall, i already set allow from 0.0.0.0 to 10.222.5.3 udp port 5246-5247 and 12222-12223.
View 4 Replies
View Related
Dec 5, 2012
Can I connect various Aironet 1242 to Wireless controller 2500?
View 4 Replies
View Related
Feb 10, 2013
I have Cisco 5508 Wlan Controller and its having 6 Fiber Ports and I have AIR-LAP1131AG-E-K9 Access Point. Can this Access Point will work with this Lan Controller? Can i connect 3 switches to this wlan controller?
View 1 Replies
View Related
Aug 12, 2012
I know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies
View Related
Jun 2, 2013
We have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies
View Related
Mar 31, 2013
We are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
View 1 Replies
View Related
Dec 6, 2012
I am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
View 1 Replies
View Related
May 20, 2012
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies
View Related
Mar 16, 2012
I can't connect to the internet. I'm currently using a USB internet, but the problem still exists. So it's not working with either cable or USB internet. It just won't connect. I've thought for a long time that there is probably something wrong with my network card, but I've run some tests that I saw on the internet, and it appears as if the network card is fine. I've also thought that there might have been a program or something that I installed that could have caused this problem, but I can't find the problem. When I go to the device manager, I can find one network card called: "Realtek PCIe GBE Family Controller". I've tried to reinstall the card, but it doesn't work. I can't find any software on the internet for this card either.
View 15 Replies
View Related
Feb 7, 2012
so i can not connect to net on my desktop but my wifi works fine, the error is the realtek PCIe FE family controller (code 31) i have tried updating the drivers but nothing i have verizion fios.
View 2 Replies
View Related
Nov 20, 2011
I am having trouble adding a new controller(2500) to the WCS.
-My WCS version 6.0.196.0
-My WLC version 7.0.116.0
If i upgrade my WCS i may add the new contoller? Even if in cisco DATA-SHEET there isnt any mention regarding this WLC(basicly it says that the WCS does not support this WLC)
Monitoring and migration of selected Cisco Aironet standalone (autonomous) access points. Monitoring of the standalone access points of Cisco 800, 1800, 2800, and 3800 Series Integrated Services Routers.
View 3 Replies
View Related
Jun 27, 2011
How to get a WLC on a SRE up and running. I have a WLC installed and running on a 2951 SRE connected to a L3 switch in a lab.
I've tried to follow the Cisco document:
[URL]...
My wireless clients could only receive a DHCP allocated IP address for the 55.XX subnets defined on the wireless lan controller and SRE (shown on page 12 of the pdf). All traffic seemed to be routed via the native vlan of the inside router trunk interface and all DHCP requests arriving at my DHCP server were from 55.XX. Because of this I didn't see the point of trunking
so I've changed it to a point to point routed connection, created a 55.XX DHCP scope on my DHCP server for the wireless clients and all routing works fine.I found the document rather misleading.
View 1 Replies
View Related
Nov 6, 2012
output are here
*Mar 1 01:28:21.018: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 01:28:21.022: %LWAPP-3-CLIENTERRORLOG: bsnSetCurrentBHRate : fail to set
radio control and data rate
*Mar 1 01:28:21.179: %CDP_PD-2-POWER_LOW: All radios disabled - AC_ADAPTOR (00
00.0000.0000)
*Mar 1 01:28:21.984: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 01:28:34.341: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigne
d DHCP address 192.168.10.244, mask 255.255.255.0, hostname AP2c54.2d0d.c3c4
View 1 Replies
View Related
Jan 19, 2011
Due to lack of wires we decided to extend our network by using WET546 bridge by linksys. Ideally we looking to create topology like this:
(Computer)--eth--(WET546)---wireless----(AP/WLC2100)---(router)---(Internet)
WET546 successfully authenticates and looks pretty healthy on controller (see below) , however neither of computers plugged to WET546 was unable to obtain ip address from dhcp server , nor working with static ip. I was under impression what it might be related to some default policies on WLC2100. Logs (warning) on WLC2100 looks clean.
View 8 Replies
View Related
Sep 18, 2012
We have a 2504 Wireless Controller and it works great!We currently have 6 Access Points (Aironet 1252) connected.We just added the sixth one a few weeks ago and with a properly configured and fully functioning Wireless Controller, it was super easy.Now, I have been assigned to add another Access Point, but at a remote site.The plan is to have up to three or more APs at this remote location and we want them to talk back to the Wireless Controller.We have plenty of licences on our current Wireless Controller.Do do not want to spend the funds for another Wireless Controller and more licenses.
1. How does one manually add a Aironet 1252 to the 2504 Wireless Controller
2. If the AP is on a different subnet than the Wireless Controller, how does one get it registered?
3. The best for last: Can a Aironet 1252 talk to a 2504 Wireless Controller over a WAN link?
View 3 Replies
View Related
Oct 23, 2012
I just turned on 2 Wirelless LAN Controllers 5508 and I am getting this message on both of them:
Loading primary image (Image not found)
** Unable to read "linux.pri.img" from ide 0:2 **
Loading backup image (Image not found)
** Unable to read "linux.bak.img" from ide 0:2 **
And it is taking me to the BootMenu. I selected option 4 to Clear Configuration and the controller seems to restart the system but I still get the same error. I checked the LEDs status and Sys is Amber and Alarm is OFF which according to the documentation is a System Crash.
View 1 Replies
View Related
Apr 15, 2012
Interface management on WCL 5508 is assigned ip 192.168.255.200 and from a PC ( on different subnet), i can ping but cannot access https to WCL but From a PC ( in the same subnet) i can ping and https.
View 11 Replies
View Related
May 8, 2012
I have cisco 4402 Wireless LAN Controller with Cisco Access Point (AIR-LAP1252G-E-K9), everything is running smoothly.How come i use my Access Points without Wireless LAN Controller, is there any possibility then which AP model would be suitable?
View 2 Replies
View Related
May 28, 2012
We have two 4400 WLC's. We have around 20 access points in our network.If we assign controller1 as primary for half of the access points and controller 2 as primary for the other half, does this mean the association of the ap's indicate load balancing by the controllers. Does this mean wlc does load balancing as different ap's associate on different controllers. or does it only server as active-standby wlc.
View 2 Replies
View Related
May 28, 2004
I've got my computer set up with a 2.4 Wireless USB Network Adapter. When I play online games I get a 'Connection Interutped' everything other 30 seconds or so.Now when I installed the Verizon stuff, the over the phone person told me to uninstall the SM Bus Controller. Now everytime I start up my computer I get a 'Found New Hardware' wizard telling me I should install the SM Bus Controller.
View 17 Replies
View Related
Mar 22, 2011
how I can find out what version of SSH that a cisco 2106 wireless LAN controller is using?Is there a CLI I can type to figure that out or do they only support one version?
View 1 Replies
View Related
Aug 2, 2012
I currently have a single 2504 Controller managing 50 AP's. I am adding a Second 2504 AP Controller with 15 Lic to manage an additional 10 AP's. My current 2504 has each port configured for my four subnets that and it is managing AP's in 4 buildings. Should I configure the new 2504 the same way so that it can see all four sites? All so if the main 2504 goes down can the second 2504 take over even thou we will be out of lic?
View 7 Replies
View Related
Sep 20, 2012
Can 2 Aironet 1042's using WDS handoff a session between them without any other network hardware needed?
View 1 Replies
View Related
Apr 2, 2013
My customer has an 1131AG AP, andhas Problems with joining to the controller. I did a debug and have the following output. The WLC (5508) shows the AP with Primary SW version as 3.0.51.0. this Release does not showup in any compat matrix! It seems to start downloading the software. after a while it stops with the bolded output, twice the same Bytecount!?
*spamApTask0: Apr 03 09:55:59.998: 68:ef:bd:94:e7:9c 5179392 Bytes Transferred to AP 68:ef:bd:94:e7:9c
*spamApTask0: Apr 03 09:56:00.097: 68:ef:bd:94:e7:9c Received LWAPP
[Code].....
View 22 Replies
View Related
Sep 25, 2012
I'm new to wireless and I have 7 Cisco 1142N (AIR-LAP1142N-A-K9) APs. But The thing is I have to buy a WLAN controller for these APs. I checked on internet and I found the 2500 series Controllers are compatible with Cisco 1142N (AIR-LAP1142N-A-K9) APs. But I would like to know How can I find the exact supporting version of controller for Cisco Access points?
View 15 Replies
View Related
May 20, 2013
i converted the C1310 to LAP using upgrade tool. but the AP is not able to join the controller i was not able to view SHA Key in upgrade tool, so i ran the "debug pm pki enable " on the controler to get it. i'm still not able to view SHA key.
here is the output of debug command
*spamApTask0: May 21 15:07:43.527: 88:43:e1:d1:fc:9e Received LWAPP JOIN REQUEST from AP 88:43:e1:d1:fc:9e to cc:ef:48:b3:23:ef on port '13'
*spamApTask0: May 21 15:07:43.549: sshpmGetIssuerHandles: locking ca cert table
[Code].....
View 3 Replies
View Related
May 10, 2013
By any way can I achieve HA in 2500 controller? I dont mind even I didnt get Stateful switchover.
View 5 Replies
View Related
Sep 28, 2010
A customer has wireless LAN controller with version 4.2.205.0 and i want to upgrade it to version 7.do i need to upgrade the controller to intermediate version or i cant directly upgrade it.
View 2 Replies
View Related
Jan 12, 2012
I have 6 of the 1252 APs that suddenly no longer will associate with any of my 3 4400 controllers. I've verified the power injectors are up and good, shut the port on the switch, and even moved from one power injector to another. Also, in WCS there is a picture of what looks like 3 disks stacked on top of each other, and I don't know what that means.
View 2 Replies
View Related
