Connecting Wired And Wireless Simultaneously?
Feb 8, 2012
situation is a little bit different than the other gyus. I have a private network of 3 laptops connected with wire to a local router (Not connected to the internet)Whenever I need internet I connect to Xfinity Wan Wirelessly. However in order to do that I have to disconnect wire first. Otherwise both connections show "Local only" The moment I disconnect the wire the Xfinity connection shows "Local and Internet" How can I access Xfinity and my wired laptops simultaneously
View 2 Replies
ADVERTISEMENT
Jan 18, 2012
I have a local wired network without the internet connectivity. It is just 3 computers connected to a router with hard wire (Not connected to outside world). For Internet I use Xfinity Wifi and connect wirelessly. However As soon as I connect the wire to the laptop the internet connectivity is lost.It says access is local only.I have no idea why it is going to the gateway after Xfinity wifi.If I disconnect the wire the internet is connected immediately. However I want to be able to see the web as well as other computers on my local network simultaneously. I tried to google several sites but could not find anyone with a similar setup (One without outside connection and one with internet connectivity)
View 3 Replies
View Related
Aug 30, 2012
I have 300Mbps PCI wireless LAN network card which I installed in my PC and until today I was connected to my Sky router wirelessly. I also have a wireless Brother all in one connected to the same PCI card.
The engineer who installed my Sky fibre broadband told me in order to achieve maximum speeds I should connect via an ethernet cable to my Sky router as wireless could be a lot slower so I bought one and connected up and disabled the wirelss card. All good so far until I noticed my Brother all in one was complaining about no network ID.
My problem is that I can't seem to run my printer wirelessly as well as run my broadband wired. If I enable the wireless adapter the printer works but my broadband is wireless as well and the wired connection is disabled.
View 5 Replies
View Related
Apr 4, 2011
At home i have a desktop Pc connected to the internet via ethernet, to a bt homehub, on the same homehub i also have a laptop connected to it but using the wireless connection. Both pcs are using windows 7.
I`m trying to file share between these 2 computers using a homegroup, but neither recognises another homegroup on their network. Is this because i`m not using the same connection method ( wirelss and wired) ? Even though both connections are going through the same Hub? I`ve tried renaming the homegroups on both pcs to the same name to see if that works, but it seems both pcs are on different networks. clear lack of pc intelligence, networking not really my thing.
View 3 Replies
View Related
Sep 17, 2012
I'm using the Dlink DIR-615 Router. It's fairly old, and has been giving me trouble for a while. Due to recent circumstances I have no choice but to use this router. I can connect to the router just fine but it does not connect to the internet whether it be a wired or wireless connection. I have recently reset the router and haven't changed any settings besides the password. (also I get the error "Your computer appears to be correctly configured, but the device or resource (Microsoft Corporation: Software, Smartphones, Online, Games, Cloud Computing, IT Business Technology, Downloads) is not responding" from window when trying to repair the connection.)
ipconfig/all:
C:windowssystem32>ipconfig/all
Windows IP Configuration
[Code].....
View 4 Replies
View Related
Jul 26, 2012
I have a wired ADSL modem+router, and also a Linksys WRT54G2 V1 router. How do I connect them such that I get a working wifi available?
View 1 Replies
View Related
Jan 4, 2013
I have an application where it would be useful to use a windows tablet PC. However there is no wireless network available and so the tablet has to plug into a wall data point.
View 1 Replies
View Related
Mar 5, 2013
in our small office, we are using Cisco SRP527W (Router/ADSL Modem all in one ) and D-Link DGS-1210-16 (ports) as our main network devices, our 3 desktops (Windows XP), Avaya phone system and one Brother MFC 6490CW are wired connected to our D-Link switch, port1 of the switch is connected to lan port 1 of our Cisco router, we also have 3 wireless devices connected to the cisco router throught wireless signal (one Broher MFC J6910DW printer, one laptop with Win7, one all-in-one desktop with Win8), as we know, both Switch and Router support Vlan feature, but at the present, I just use default Vlan (Vlan 1) for all our data traffic, I created a DHCP Pool in Cisco router to provide IP address to all our devices (DHCP Pool: 192.168.30.101 - 192.168.30.250, Default gateway is 192.168.30.254), All wired or wireless devices can get right IP address,and all of them are able to get on to the internet, the problem is wireless and wired devices can not talk to each other, for example, my laptop is using wireless connection, when I try to ping a desktop which is wired connected to switch, there is no response, however, if I cable connect my laptop to switch, I am able to talk to the desktop and use its shared resource.
View 2 Replies
View Related
Mar 3, 2013
I was wondering if there was a way to connect a wired printer to my linksys E3000? or am I still stuck with using my spare desktop.
View 4 Replies
View Related
Feb 7, 2013
I am having issues figuring out how i can make AppleTV,Airprint, Airplay, etc show up on Ipads that are connected to the wireless network. The controller is at a main site which is seperated by 2800 series routers at the remote sites over 100Mbs links. Ipads connect and tunnell back to the main site. I've tried enabling FlexConnect but the devices still get the main site's addressing so i'm guessing they are still tunneling unless the AP loses connectivity to the controller. I have two SSIDs (staff and students). I have tested with just setting the staff to FlexConnect. Do I need to set both SSIDs to FlexConnect to make them dump data locally? AppleTVs are connected wired to the local networks and get addressing associated with that building.
View 8 Replies
View Related
Oct 13, 2011
I am running Ubuntu 10.10 on a Dell Inspiron 6400.I am able to get 10/100 Ethernet card and Wireless Lan working independently. If I restart/reboot my eth0 turns starts up fine.If I then manually start my wireless connection (eth1), eth0 disappears.
There seems to be issues with wireless drivers: I don't have the cleanest solution but I run this script: [code]
Is there any way I can have them running simultaneously? From reading around I believe it's possible but not quite sure what I'm doing wrong.
View 1 Replies
View Related
Nov 27, 2011
My PC running on Windows 7.I'm connected Internet via Wireless adapter. [code] But after connect VPN i'm not able to connect Internet anymore. I think because there are 2 gateway in there. and the default gateway become vpn network. In my case. How to connect vpn client and internet wireless adapter simultaneously?
View 1 Replies
View Related
Jan 28, 2013
Can i run both 2.4 and 5ghz at the same time? so my N user's can connect at 300Mpbs on the 5ghz bonded, and my G users can connect to 54Mbps?Also i ask because of coverage, my 5ghz does not cover as far as the 2.4 so those at the extremity's could at least get G with a good signal?
View 4 Replies
View Related
Aug 2, 2012
I have a Linksys WRT54GS2 router, a PC (Windows XP) and a laptop (Windows 7 Ultimate 32 bit).I have been using this router for 3 months. I was able to use the internet on both devices simultaneously until now. But suddenly since yesterday it only works for one device at a time, not both.
If I connect to the router then I can access the internet only from the laptop. To use the internet from the PC, I have to power off the router, type in run "netsh int ip reset resetlog.txt", and restart the PC. But as the router is off, the internet is inaccessible on the laptop.
While router is on, the PC shows limited or no connectivity.
I tried reseting the router 2-3 times.
On the laptop it sometimes shows "IP address conflict has been detected", even though the IP addresses of the devices were not the same. The IP address of the PC shows 169.X.X.X (when the router is on), whereas the ISP's IP addresses start with 124.X.X.X.
View 1 Replies
View Related
Apr 10, 2011
For whatever reason, as of Tuesday afternoon my laptop can no longer connect to wired internet. I am a college student (NYU), so I cannot access a modem or router myself. I have tried:
-Plugging my cord into another jack in my dorm room
-Using my roommate's ethernet cord
-Taking my cord and laptop to different areas on campus (library, other dorms, etc) that use different wired networks, and attempted connection there Worth noting is that I can still connect to wireless internet just fine (however, my dorm does not have wireless, making things very difficult for me).My ethernet adapter is a Realtek PCIe GBE Family Controller. It was just updated today, in hopes that maybe it was a driver issue (Prior, it was a Realtek 8168C/8111C, whatever that means). All drivers have green checks next to them and appear to be working. Here is my IPConfig info:
Description : Realtek PCIe GBE Family Controller
Physical Address : 00-1E-EC-55-91-1F
DHCP Enabled : Yes
Autoconfiguration Enabled : Yes
Autoconfiguration IP Address : 169.254.26.193
Subnet Mask : 255.255.0.0
Default Gateway : (blank)
I am running Windows XP Service Pack 3. My laptop is a custom-built CyberPower PC. I have done a Malwarebytes Scan,SuperAntiSpyware Scan, and Avast Anti-Virus scan, and have turned up no malware or viruses.
View 2 Replies
View Related
Jun 13, 2011
Okay we have the router downstairs with a powerline ethernet on the firs and second floors so we can get the net.
Our house must be made of lead or something, because I very rarely get a decent wireless signal which stays consistant. Because of this I wanted to connect my laptop though the powerline but for some reason it doesn't work.
When I plug in the network cable it just hangs on identifying for a minute or so then comes up with "unidentified network" saying its connected, but has no access to the router, the internet etc etc.
Connecting the laptop directly works fine however. I've also attempted plugging the laptop in via a usb / ethernet connector, but that still hasn't given any results with the exact same issue. When i run ipconfig /all this is what comes up.
Quote:
Windows IP Configuration
Host Name . . . . . . . . . . . . : wowfood-PC
Primary Dns Suffix . . . . . . . :
[Code]......
View 6 Replies
View Related
Jan 15, 2011
I have a linksys wrt54g router. i need to block all devices except one from plugging in a wired device into the back of the router. i tried the mac filtering, but i didnt work. Is that for wireless only?I can also block local ips (192.168.1.x), and was going to go that route and only allow my local computer but i was afraid if i restarted my router or computer the ip would change and i would be locked out.
View 2 Replies
View Related
Jan 12, 2013
1.) I don't have a wireless card in my PC, so I will be connecting wired to get WiFi via WAN and LAN ports, right? I have a Windows 7 32-bit desktop PC. We are working with a DSL modem residential line without phone line using a coaxial cable, and Ethernet cable from modem into the PC. provide step by step walk through instructions by connecting this D-link router to my modem and WiFi, and for me to use the WPA2 security?
2.) I have an iPhone 4 with Verizon. If I want to use my iPhone to get WiFi from the router, and turn off the Internet, and use WiFi only on my phone, how would this work?
View 14 Replies
View Related
May 18, 2012
I recently borrowed a friend's desktop and I am having issues with connecting with the router through an ethernet cable. I go to troubleshoot the problem and I get "Local Area Connection 2 doesn't have a valid IP configuration". Its nothing with the router because when I plug my laptop in with the same ethernet cable, I am able to connect perfectly.
View 19 Replies
View Related
Mar 3, 2012
My buddy just purchased a Sharp AR-M450 multifunction printer for his small business and it has the optional network card. He wants to take advantage of the network printing capabilities but we want to avoid having to run an ethernet cable from the printer to the wireless router. The entire network is wireless because running cables would be a huge pain in the building he is in. What could we use to connect the printer to the network without running cables?
View 1 Replies
View Related
Feb 16, 2011
i need to connect a linksys e1000 to an existing dlink router. i have tried several solutions that i have found on the internet, but none have worked. i need DETAILED instruction tailored to e1000 specifically because i am having trouble with dhcp definitions as i have not done this in years. i can get it to work, but i have to maintain security and everything i have done still allows me through to dlink router.
View 6 Replies
View Related
Apr 30, 2013
Small office, 2 RV042, 2 DSL connections. 1 is used striclty for the business side, and the other is for our CCTV network. They also have seperate DSL connections as we have 2 external IP address for clients to connect remotely. We don't want to take away our exisring setup, but would like to bridge both networks so a few of our internal clients can connect to our CCTV network and use some of the devices. Right now they come in on VPN but its not as fast.Is this doable without adding additional hardware? Both networks need DHCP enable as well.
View 1 Replies
View Related
Jul 4, 2011
Final results are that if I hard ware connect my computer to my PS3 I can acces Media Servers.When connected through the router though my computer acknowledges the PS3, it cannot connect to Media Servers.I have the Linksys BEFSR41 v4.3.
View 3 Replies
View Related
Apr 20, 2013
I have a BEFSR41...about 2x a week when connecting to internet I have to pull and replug router in order to get on-line.
View 3 Replies
View Related
Sep 16, 2011
I have a home network that uses a DLINK DIR-655 router. All of my devices ( a mix of wireless and wired) except one--a windows xp SP 3 desktop that stopped working yesterday. Some viruses, and adware were detected and it has not worked since then. What I have done.
View 11 Replies
View Related
Jan 27, 2011
I bought a Cisco Linksys RV042 (Firmware Version: 1.3.12.19-tm) a month ago. I installed it with two Cable Modems (Webstar DPC2100R2) from the same internet provider and with the same individual bandwidths for the two of those. My setup is Dual Wan mode since I only bought this device for load balancing the traffic through the two WAN connections. I need to clone both WAN MAC addresses on the router ports in order to get connected to my ISPs provisioning server. The RV042 has no issues getting a connection on WAN1 when MAC cloning has been made on this port, however, when I clone (user define, different from WAN1) MAC address for WAN2, this port never gets a connection and stays on IP 0.0.0.0 all the time.
I’ve tried factory reset, reloading the latest firmware (which already came pre-installed), switch modems from WAN1 to WAN2 and vice versa, disabling Firewall, turning on and off the ports on Port Management tab, changing SmartLink to Load Balance mode, enabling and disabling Network Service Detection, DHCP vs. Static IP on WAN ports, manual setup, setup through the wizard.
Nothing seems to make WAN2 port function correctly with the User Defined MAC address. The only way to make it work is using the factory (default) MAC address on WAN2, then it gets the IP address from the modem. Again, WAN1 works correctly with a user defined MAC address same as with Default MAC address enabled.I have read endless customer’s posts having the same issue from several years ago in this Community Forum and all over the web, and none of them have had a definite solution to the problem from the manufacturer.
View 1 Replies
View Related
Jul 29, 2012
i have two diffrent-2 network connection and now i want to use both connection for load balancing and speed browsing.
View 2 Replies
View Related
Jul 4, 2011
will the use of mobile wireless internet connection and broadband inet connection simultaneously can be used to download softwares or video files faster than these two used seperately?
View 2 Replies
View Related
Apr 2, 2012
My Linksys WRT120N router was working fine for all of 1 and 1/2 months and suddenly it stopped making the internet connection. At first nothing could access the internet but now that I've reset the router (via the little reset button in the back) my Kindle can access the wireless, but of course no password etc. I actually don't know how to put back the username and password for it. When router is connected: When I troubleshoot the connection by clicking on "Repair Connection" it takes about 2-5 mins "obtaining a new network address" then I get an error saying "The wired connection to your router was not automatically repaired. X Local network: Not connected.
View 14 Replies
View Related
Dec 26, 2012
I want two connect two usb modem simultaneously on the same pc.How can I?
View 5 Replies
View Related
Jul 20, 2011
I am running windows xp on an old desktop, I am using a wiresless usb adapter to utilize a wifi connection available in the dorms. to connect, i have to enable proxy on the browser I am also using an Ethernet connection via a LAN cable, which does not need a proxy to run
The issue is that although i browse freely using both connections simultaneously by using two different browsers, with the proxy setting enabled in one and disabled in the other, i can not run uTorrent when both connections are enabled. i have to go into network neighbourhood and disable the wifi connection, and only then does downloading start. the university does not allow bit-torrent downloading on the wifi connection so i have to use the ethernet.
View 1 Replies
View Related
Jan 3, 2012
Can i connect two internet dongles simultaneously to my internet n get more speed?
View 1 Replies
View Related
Jun 10, 2012
It started happening back in around November, my sister and my computer would start freezing occasionally, slurring the audio into a robotic sound, eventually to come to.It gradually got worse, and I assumed it was a graphics card problem since it would freeze ONLY SOMETIMES and say that the graphics driver stopped working and has recovered. It usually didn't say that, though.Lately though, I noticed that when it would freeze sometimes the internet would go out for some connected devices, such as the Xbox 360. The only computer that was NEVER affected by this is the one connected directly by Ethernet to the Netgear router, (every other device is WiFi.)
Sometimes even, my sister and mine would freeze simultaneously. It was a sort of rare occurrence, though.I very lately started to notice that it would freeze when trying to load internet components with larger amounts of data, such as server console logs, Flash videos, and Soundcloud players. What threw me off is that it would sometimes freeze in programs like FL Studio or Windows Media Player... It's possible I guess that the programs were unrelated and what caused the freeze is SOMETHING sending/receiving corrupt packets.
View 6 Replies
View Related
