I have 2 routers and would like to create a wireless bridge/repeater between them so i can extend my wifi range. Is it possible to do this? and How would I do it.
Router 1: Aztech hw 550-3g
Router 2-Link DWR-113 3g
I am having trouble creating a network bridge between my PC and Blu Ray player via LAN connection. I have done it before, but always run in to problems. I took my computer on vacation and messed up the existing connection and settings. Last time I successfully created the connection, I stumbled upon the answer, but can't remember how I fixed it. I should say that I can create the bridge, but once I do, the wireless internet connection no longer works, and my blu ray player can't connect to the internet either. I have forced compatibility mode on the wireless network via DOS, but no luck. I did the same on the LAN connection just for the heck of it. Still no luck.
View 10 Replies View RelatedI'm experimenting/attempting to use a laptop as a network tap between my (DSL) modem and a wrt54gs by creating a bridge with two NICs in the laptop. My problem is I can't seem to get connectivity on the user end of the router. I can't ping the bridge from an end computer...
DHCP is disabled in the router, but even when manually configuring the IP address on an end computer and using the bridge as a default gateway I can't ping out.
Am I completely misunderstanding the purpose of a NIC bridge?
I'm having trouble setting up a wireless internet connection for my computers, I connected the patch cable from my modem to a wireless router, then connected to that network with a usb for my computer.I was able to connect to the network, but couldn't seem to actually get into the internet. Is there any solutions to this?
When doing ipconfig /all, the message I get is:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Victors
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
[code]....
I was in a pub the other day. When I tried to use their wireless I was directed to a webpage to enter the password.I am a web designer and want to make a funky login page, not for a user ID. Just to enter the password to my wireless.How do I do this? Im not aiming to make my system more secure.
View 1 Replies View RelatedI have 2 laptops, one is running VISTA and one is running Windows 8. They are connected to my wireless router. I also have a desktop running Windows 7 that is wired to router. I have searched the internet and cannot find how to set up a new network without using a HOMEGROUP?
View 2 Replies View RelatedI have desktop with windows 7. I am connected to internet through D-link ADSL 2+ router using RJ 45 cable. I want to create wifi hot spot on this desktop. I tried installing connectify software. But when I try to configure hot spot with connectify it says No wi-fi device present. Now what hardware do I exactly need to turn my comp into wifi hotspot?
View 2 Replies View RelatedI have a wireless network and I have a new TV that has wireless and wired connectivity. I do not have a wired port at the spot where the TV is mounted so I am connecting wirelessly. The problem is the wireless on the TV is pretty flaky and I cannot get consistent connectivity..and every time it can't connect I have to retype in the AP passwords as it doesn't remember them. I would like to switch the network to wired, but can't run an actual wire. Can I add a new wireless AP as a repeater or bridge to tap into the existing wireless network and then connect the TV to the a wired port on the wireless router?
View 10 Replies View RelatedRegion : India
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
i need to create a network with four computers and i have a tplink gigabit switch(wired) and plan to buy a dual band wifi gigabit router the sending and receiving end are just about 10 meters and are parellel that is i have to transfer and share data across street i plan to use one of the computer as primary data server and one of computer wired in with it with cat 6 cable and two others across street with wifi the transmission has to be lossless as its accounting and varous other files are being shared?
Basically what is happening is I have a fiber decoder whitch goes into My belkin modem which controls my phone and Internet and with the company I am with we need that modem, I also have a netgear router so I can have wireless through my house but I want to plug LAN into the belkin router and still use the netgear for transmitting wireless.In short I want LAN in belkin but still have the netgear transmitting wireless and everything on the same network,E.g I have a pioneer amp and I use the iPhone app icontrol over my wireless but I can't because the amp is plugged into the belkin and the app is using netgear.
View 1 Replies View RelatedIs it possible to create a managed schedule to switch the wireless radio on/off? I want to set a start time and a stop time so that e.g. the wireless can be switched off during nighttime.
I had previously routers from both dlink and zyxel and they both had this feature.
I am sensitive to electromagnetic radiation and bought the EA4500 due to the 5 Ghz capability, - but then only to discover that the radio always has to stay on (at least as far as I have found out.
I read the User Guide section on Internet Access Policy for the Linksys E3000 but I could not find this menu to create a policy from the web interface. I have the latest firmware version (1.0.04 Build 6,)
View 1 Replies View RelatedCan I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies View RelatedI want to create a DMZ by having a less sophisticated router connected to cable modem, which would have the webserver which contains no sensitive information, and then the EA3500 to which my laptops and desktops which contain sensitive information would connect to. Can CCC work through that first router?
View 6 Replies View RelatedMy customer need creates some separately web portal for some SSID (Guest and Staff), 01 web portal for Guest and 01 Web portal for Staff. Can WLC2504 can support this features ?
View 2 Replies View RelatedI have been involved in the Networking of a museum with a set of "Show" computers which display video, and for this reason cannot have anti virus installed becuase of the performace hit, and also the risk of pop-ups on the videos. They do however need to be connected to the internet as some are interactive and allow people to send simple emails, and they all need to allow remote support when things go wrong.It seems the networking was not thought out very well initially, and there is a single wireless router which serves the staff and public on a secured wireless network, but also serves the "Show" machines via a wired connection from one of its ports, which then connects to a master switch which serves the show machines.Now the wired and wireless is on the same network, and everything shares the same IP subnet (192.168.1.xxx), and this is not a good situation in terms of the securuty of the show machines on the wired network. So I need to work out a way to totally separate the wireless network (which will be very prone to people opening viruses in their emails etc), from the wired network (which will be the show machines which wont be touched by anyone).
I want to achieve this in the simplest and easiest way, and have been reading about the possibility of setting up a second wired router behind the current wireless one, with a different subnet IP address, to which the "Show" machines could be connected. The WAN port on this second router would connect to a LAN port on the wireless router, and thus the show machines could get their internet, but separated from the dangerous wireless network.Does this sound like a sensible start? Will the fact that the wired router (and show machines) are on a completely different subnet to the wireless router (and wireless devices), mean that the wired network will be protected? Or do I need to do more? And is this likely to work?
I has got a 8 system(Say Node1, Node2,.....,Node7,Node8) in my LAN Network.i Want a Group a 8 System's in Such a way that Node 2 Should Ping with Node1,Node3 Node4, But not with Node 5,Node 6,Node 7,Node 8.
View 2 Replies View RelatedI'm trying to create a VPN at our office. However I cant seem to ping our servers public IP. I have tried configuring our router to do this. However, it times out when you are outside of our network.
View 4 Replies View RelatedI have a VM (Alice).I want to route ALL its traffic through a server of my own in the UK.It needs to be 'fail-safe' in the sense that the traffic must either be routed through the server, or not at all (EG with windows VPN dialer, if the VPN connection is dropped it will immediately begin routing traffic normally again - that's not acceptable*). I need to run windows on the VM, the server can be anything.The VM is connected to the internet via a linux firewall/router box in my house (set as default gateway for the VM).How can I set this up?
View 5 Replies View RelatedI am a bit confused on how to create a Hot Spot & connect a Dell Desktop(no built in WIFI) a Dell Laptop(with built in WIFI) & a HP Printer with WIFI. From reading info on your Web Site, it appears that I need a Wireless Router, an adapter(not sure what this is) for my Desktop. I have AT&T Air Card internet access. Do I need anything else?
View 1 Replies View RelatedI'm trying to set up a network for a friends small office so we can share files between each of the computers.i have tried to do it through the workgroup but with no luck as some can see the other machines and some cant?
Hardware/software:
Thompson wireless Router
laptop with Windows 7
laptop with Windows Vista
laptop with Windows XP SP2
Mac
I have set the network discovery to on in W7 & Vista and and ran the network wizard in XP At the moment the vista and W7 machine can see each other but i get and error saying cannot access //(computer name)with the W7 and XP machines i can send a file when i type in the ip address (//192.168.1.?) into the W7 search bar but the XP computer is not shown in the network folder?
I have been assigned to create a basic IP Addressing Scheme. The company has a single class B private address range of 172.16.11.0/16 and it needs to be divided into four subnets. They are all based on a single router.
Subnet A: 500 hosts
Subnet B: 200 hosts
Subnet C: 50 hosts
Subnet D: 20 hosts
How can I subnet them correctly and how would I make an addressing scheme for each subnet? (Host range, server, peripherals, gateway address? etc.)
What is the best way to set up a VPN connection?
View 2 Replies View RelatedSo i'm new to this sort of thing i am building up 2 gaming pc Windows 7 so while i have both for a few days i would like to network them so that when i want to play a car racing game via lan the other pc will detect itone gaming pc is mind the other my fren so until i deliver it to him i have it for a few days so i wanted some practice in thisso i have a WIF arris modem with 4 Ethernet ports so both sys will be connecting through cablesi would like a step by step guide as to how to go about doing this creating domains et
View 2 Replies View RelatedI am looking at using a TP-Link Powerline Adapter (TL-PA211 Starter Kit) and a Trendnet 4-Port Broadband Router Tw100-S4@1CA (both listed on Amazon) to connect my Hitachi L32A402 HDMI television and a Roku XD|S to the internet to use Netflix. And also to connect my housemate's new laptop.
I believe the setup would be from my Dell Vostro desktop to the Trendnet router to one of the TP-Link Powerline Adapters. This would be on the second floor. Then in the basement I would need to plug in two additional adapters ... I would connect one to the Roku and then to the Hitachi tv and connect the other one to my housemate's computer.
My questions are:
Can I keep the computers not visible to each other? We would both like to maintain our privacy ... and I don't know if we connect everything up this way if our computers will be open to each other. Is this called putting them on a separate network?
I saw something in the documentation in this manual [URL]. I think on page 20 it is telling me I can give one adapter a different name to put it on another network, but I am not sure. And I also see that it also says for there to be connectivity they need to have all the same name "HomePlugAV".
So, if the tv and the main adapter have "HomePlugAV" as a name, and my housemate's adapter has a different name ... then they will all work (get on the internet) - but my housemate and I will have privacy?
Are there any issues about anyone being able to access my computer through the tv ...
Creating an image is almost always a success. However, when restoring, sometimes the process gets stuck somewhere (the client reboots prematurely if that happens) and more than often the clients can't boot into Windows anymore.All clients have the exact same hardware.Now I know the image can't be the problem, as I've restored this exact image to a client two days ago and it booted perfectly fine. Everything worked.I tried to image two clients at the same time. The first thing I noticed was that the method used was NFS and not UDPCAST, which it should be. Now I know it wasn't using multicast because the imaging went asynchronous.
View 14 Replies View RelatedI'm starting college in the fall and will be living in the dorms on campus. I want to have a "private network" setup within the university's network in my dorm room so my and my roommate's phones and iPads can still find my Apple TV, file sharing and network drives are still possible, and I can easily set up my network printer. Obviously, I don't want to lose Internet connectivity. Can I use NAT to accomplish this without losing Internet connection through the university?
how the sysops will hate me if they find me, I know this. It's not for malicious use, only for ease of use of my devices.
This may be totally off base, that's why I'm asking if this will work before I try it. I have an old WRT54G I would like to use if its capable, if not I'll buy a new one but I'm trying to avoid that. Here's what I'm thinking:
My router plugged into the University's Ethernet port in my room (for this setup do I use a LAN port or the WAN port on the router?) DHCP disabled, all devices static IP On the "Advanced Routing" tab: "Router" mode, not "gateway" mode What should my destination LAN ip be? Gateway? LAN & Wireless or WAN?
Switch connected to the router
Devices connected to the switch or connected wirelessly Should my gateway and DNS on each device be the host address assigned to my router?
i want to create a LAN between 3 nos of windows 7 installed computer
View 2 Replies View RelatedI am having a problem in which when ever I check "Computer" later on in the day, one of the network drives is duplicating itself over and over using a different drive letter each time. By the end of the day if untouched I can have approx 20 of them!To give you more information about the scenario, the computer is on Windows 7 pro, it is on a domain in which the server is 2008 r2, there are 2 network drives in total (only one is duplicating), the only 2 changes I recall that may have caused it is box.net is running on the server syncing all content on the networks drives and a new printer has been added on the network.
View 5 Replies View RelatedI'm creating 3 vlans, one private ip addresses and the two for two blocks of public ips. After creating them devices on the same network are able to talk to each other on the private IP but not on the public ips.
View 1 Replies View Relatedi am trying to make site to site VPN on cisco 1841 router using SDM , but I faced a strange problem . I successfully install sdm , internet browser , disabled block pop up , and java . i successfully can run SDM and configure the router using it .
BUT\ when I select VPN>>Site to site VPN >>Create Site to Site VPN tap >> and Press on Lanuch the selected task to start the creation process using the wizard Unfortunately it is not working ,, I don't know why ?
I tried with another PC , another SDM version , another browser .
New to Cisco devices and have had an ASR dropped in my lap.Running ASR1000-RP2 with System image file: asr1000rp2-advipservicesk9.03.03.00.S.151-2.S.bin Show Vlans returns: No Virtual LANs configured Router(config)#interface vlan?
<1-4095> Vlan interface number
But when I try an assign a Vlan number I get % Unrecognized command, or % Incomplete command
we have two Catalyst Express 500 switches and a ESW 520 just purchased. the VLAN on the other two is 2. how do I change the Default to be 2 instead of 100 in the ESW Switch.
View 3 Replies View Related