I read the User Guide section on Internet Access Policy for the Linksys E3000 but I could not find this menu to create a policy from the web interface. I have the latest firmware version (1.0.04 Build 6,)
View 1 RepliesInternet policy access on my Linksys E3000. I am trying to block facebook.com to a particular ip address in my office. This what I did. Logged in to control panel clicked on access restriction. Clicked on add. Gave it a name. Clicked the applies to drop down box and selected by ip address. Unchecked the block all internet access. Typed facebook down in the window below. Saved.Not blocking access.
View 9 Replies View RelatedBEFSX41 V2.1
Firmware: 1.52.16
The manual states how to create an inbound traffic policy but if you follow the directions there is no place to select inbound traffic.From the manual: To Create an Inbound Traffic Policy1. Enter a Policy Name in the field provided. SelectInbound Traffic as the Policy Type.2. Enter the IP Address from which you want to block.Select the Protocol: TCP, UDP, or Both. Enter the portnumber or select Any. Enter the IP Address to whichyou want to block.3. Select Deny or Allow as appropriate.4. By selecting the appropriate setting next to Days andTime, choose when the Inbound Traffic will be filtered.5. Lastly, click the Save Settings button to activate thepolicy.When finished making your changes on this tab, click theSave Settings button to save these changes, or click theCancel Changes button to undo your changes.I want to filter out a range of ip addresses from trying to connect to my network.
When I click on "DHCP Reservation" button in the web interface of the E3000 I don't see any information about the current devices and the reservation list.This problem occurs when my sattelite reciever tries to get an IP address from the DHCP.the name of the receiver is "dream box" (no special characters).I didn't have any problem in the past with my previous router (3COM)Since there are error messages in the page (screenshot is attached), I've tried to use different browsers but the result was the same (Firefox, Safari, IE 8)
View 9 Replies View RelatedI just installed my new Cisco E3000 and configured it over the HTTP interface, as I have on previous routers. I am unable to find any setting for the "Guest" wireless network (outbound internet only), or the Parental controls. Both of these are features of interest, and they're simply not listed in any of the web-based settings.
Puzzled, I did a Factory Reset and configured it via the Cisco Connect instead.. this had the Guest feature and Parental controls, but none of the other features I need, like QOS, or Port Forwarding, or DHCP disable.
It seems like the Web interface only configures some settings, and the Cisco Connect configures other settings, but I can't use them both.
Where does one set up the additional password for Guest access? Other than this, the router works fine on 2.4 & 5 GHz, nice..
I have an ASA 5505 at each of three locations. We have VPN tunnels set up between the three sites. I am currently using a single ISP to control the traffic between the sites. I am adding a new ISP to the mix. The goal is to have any internet traffic routed to ISP 2 and all internal traffic routed to ISP 1.The ASA does not do policy based routing (mostly because it is a firewall, not a router). I need to configure a router that will accept the output of the ASA and route it according to the above rule. All incoming routing will be done through ISP 1. Any suggestion on the device and the methodology to set it up? I am planning on doing this in each location.
View 3 Replies View Relatedi have a cisco router 7206 ,when i create subinterface with ip , the router hangs , and all interfaces are down ,i just remove interface gi0/1 and plug it again, what is the relaiton between subinterfaces and hanging routers> the problem occurred when i configured sub-interface on GI0/2. [code]
View 13 Replies View RelatedI have configured a qos policy and I am trying to apply the policy to a vlan interface which is physically connected to a switch module port of a 3845 Router.When I try to apply, the message configuration failed appears.
View 4 Replies View RelatedIs it possible to create a managed schedule to switch the wireless radio on/off? I want to set a start time and a stop time so that e.g. the wireless can be switched off during nighttime.
I had previously routers from both dlink and zyxel and they both had this feature.
I am sensitive to electromagnetic radiation and bought the EA4500 due to the 5 Ghz capability, - but then only to discover that the radio always has to stay on (at least as far as I have found out.
I want to create a DMZ by having a less sophisticated router connected to cable modem, which would have the webserver which contains no sensitive information, and then the EA3500 to which my laptops and desktops which contain sensitive information would connect to. Can CCC work through that first router?
View 6 Replies View RelatedThe Internet Access Policy feature of my WRT610N router doesn't appear to work, at all, zip, nothing, nada. I have setup the feature todeny access to one of my laptops for everyday 24 hours a day, but it can still use the net...
View 5 Replies View RelatedI just bought a factory refurbished E1200. The label on the bottom says it is a Version 2 model. When I purchased it, it was loaded with 2.0.02 firmware but I upgraded the firmware to 2.0.04.My problem is that I'm trying to setup MAC address-based restrictions thru the manual/web-based setup and when I click on the "Access Restrictions" tab, I only have simple "Parental Controls" and not the advanced "Internet Access Policy".Is it possible that I have a mislabeled V1 device? If that is the case, how is it that I was able to upgrade the firmware using firmware from the V2 downloads section.
Do V! and V2 units use the same firmware but more importantly, how do I upgrade the built-in software so that I have the advanced "Internet Access Policy" controls?
I am trying to set up an access policy on my WRT400N. Whenever an access policy is enabled, all internet acess is completely blocked. This occurs irregardless of what the access policy is supposed to block. Even a blank access policy that allows access to everything and doesn't have any computers registered still blocks everything. How do I get it to stop completely blocking internet access?
View 9 Replies View RelatedMy WRT120N router doesn't have Internet Access Policy when I access it.
View 2 Replies View RelatedI have WRT150N, with firmware version 1.01.9 and I can not get the internet access policy to work.Here are my settings: PC list is configured through IP range as follows:Even if I deny internet access completely, I can still access the internet.
View 2 Replies View RelatedI setup E4200 good. But, in Access Restrictions, there is no policy to choose from. Just Parental controls only.restore the Internet Access Policy like the good old routers?
View 1 Replies View Relatedwhy i can't add a new policy. I can't fillin a policyname or change the status from disable to enable. I have model V2 with firmware v2.0.03 build 007Jul 2, 2009
View 3 Replies View RelatedI'm just about to trade-in an E4200v2 for a E4200v1, primarily to regain the "Internet Access Policy" capability.
Just wanted to do a reality check with those of you who tried/use IAP... does it work basically as advertised?
I would be using IAP to specify MAC addr's of devices, blocking them from certain URL's and limiting their hours of Internet access.
And I plan to have Linksys's DHCP Server turned OFF, since my Windows Server handles DHCP on my network.
Should I expect all of this to work OK? No major reliability problems with IAP?
I have a Linksys E3000 router set as Lan-Lan 192.168.0.2 hosting my internal LAN connected to a motorola Surfboard (Brighthouse) internet Wireless/Wired access point 192.168.0.1.I have a Web server hosting a site connected direct to the surfboard (works fine) . The FTP "site" on the E3000 can be seen by all pcs on the internal LAN. However, it can NOT be seen from the internet (Android with FTP client being used for test device)
Primary Access point 192.168.0.1
DCHP server with reserved IP addresses for server and PC's and smartphones
Port Forwarding Set for Server at 0.004 : 80
Port Forwarding Set for E3000 at 0.002 :21
Secondary (E3000) router 192.168.0.2
DCHP server is disabled
Port Forwarding is Not being used
connected to primary router LAN port 1 by LAN port 1 on E3000
All pc's can access the Internet when connected to the E3000 via cable or wireless?All pc's can access the FTP server on E3000 via cable or wireless as a LAN location (connected to either router)?How can I get the FTP to be seen from the internet ?
I recently bought a Cisco e3000 router. I updated the firmware but I am still only getting 1.33 Mbps at most. The only things plugged into it is my PC and my xbox. I bought the router so i could get a better connection on my xbox so netflix wont stop playback.
View 9 Replies View RelatedOn E4200 Firmware Version: 1.0.03, I managed to successfully set up "Internet Access Policy" (not the "Parental Controls") to set up the times when internet access is disabled for various IPs on my network.
But I could't setup a policy to block facebook.com. What I am doing wrong? See the attached screen shot. I did click the "Edit List" and apply this polity to the IP Address Range 192.168.1.2 to 192.168.1.254.
I have in my possession three E2000 and I wanted to buy 3 more, but the model seems to not be on sale anymore so I bought his successor the E2500.In the E2000 I used the Internet Policy menu to block internet access of certain computer by entering their mac address.In the E2500, they seem to have removed this menu to replace it with a Parental Control menu, which offers far fewer options, basically you can only block a computer that is connected to the router, you can not block a pc by the ip or by his mac address.Is there a way to have a menu similar to Internet policy in the E2500? A hidden menu, or a different firmware?
View 1 Replies View RelatedI've reset my router, reinstalled Cisco Connect and didn't configure anything on parental controls.However, when I navigate to the "Access Policy" menu all I see is parental controls. I don't see any of the more sophisticated filtering menus like "access blocking policy", etc. I've attached a screenshot.
View 4 Replies View RelatedI have an e3000 that cannot obtain an address from the ISP. I can get an address on the computer and an old router by directly connecting the cable to the computer or the router. I can also daisy-chain the e3000 to the old router, and I can get an address on the e3000 from the old router. I have hard reset the e3000, changed firmware from the Linksys to TomatoUSB and back to Linksys, and I still can't get it to work. It worked fine on Saturday until a bolt of lightning hit close to the house. Since then, I cannot get the e3000 to connect to the ISP.
View 9 Replies View RelatedHow do you set up the E3000 for ATT u-verse?
View 2 Replies View Relatedinstall linksys e3000.
View 1 Replies View RelatedI had a failed Tomato upgrade and now Connect Setup can't see router to revert back to original. I get message 82BD0101 or computer not connected to router. Also the http://192.168.1.1 trick won't work. Is there any way to restore besides 30/30/30?
View 2 Replies View RelatedI would like to override the DNS servers provided by DHCP via my ISP. The other settings I would like to preserve (like my assigned IP).How to achieve this with E3000 ?
View 3 Replies View RelatedIt seems like after a certain amount of time, maybe a few days... my E3000 gets slowww.. I'm talking dog slow. And it's not just the internet, I have a media server connected to it, and usually when I put something on it, the transfer rate is about 3.5MB/s (not bits, bytes). But everything is slow, I top out at speed of maybe 1/6 normal on the internet as well.
View 8 Replies View RelatedWe have a wireless internet service. Not satellite. We basically have an antenna on our house that picks up the signal from a tower a mile or two away. I used the e3000 router when we lived in town with broadband internet and it worked fine. I can't get it to keep a hold of a signal. I can connect to the router from the computers but the router drops the signal from the tower. I have an old router that the wireless company was kind enough to lend me that works , but the signal is weak and it could die at any moment... I"m at my wits end.. I have an expensive piece of equipment that wont hold the signal. I have updated the firmware and the Cisco connect software..
View 5 Replies View RelatedHas anyone tested QoS on the new E3000? Whenever I add an application (e.g. Voice Device) and set priority to Medium or High, my upstream bandwidth for everything else is immediately cut significantly, even when I'm not using the priority application.
For example, with QoS disabled, I can consistently get 10Mb upstream (speedtest.comcast.net). As soon as I enable QoS, upstream is capped to exactly 2Mb! On my old router, there was an option to set the total upstream bandwidth -- but on the E3000 there is no such option that I can find.
just bought an e3000 and want to use it with wireless internet- usb modem. when setting up it wouldnt go any further than the 'searching for connection' page as it couldnt detect a connection in the 'internet' lan (wan?) port.can i set it up to accept the wireless usb modem?
View 6 Replies View RelatedI lost my cd for my router e3000 any way still to use it?
View 1 Replies View Related