D-Link DIR-615 :: Network Drive Shuts Down Router

Nov 10, 2011

I have the Dlink DIR 615 router, windows 7, and this morning, it suddenly started to shutdown and restart, over and over.  I unplugged all ethernet connections, shut down, etc. and slowly added the PC, then the phone, until when I plugged in the Western Digital 2TB My Book live, it would begin the same restart process. I can now repeat the issue by unplugging, and replugging the drive. I have had the network drive for about 3 months, and this started today. 

View 6 Replies


ADVERTISEMENT

D-Link DIR-655 :: Web Surfing Shuts Down / Everything Else Stays OK

Aug 27, 2011

I am ignorant with networking.  The most I know is /ipconfig.I am stationed in Japan and have a fiber modem going into my DIR-655.  For about two years everything has been fine...no problems ever.About a month ago, I started getting timeouts and page not found errors when surfing the web, but my online games (EVE, WoW, etc) and our Xbox360/PS3 work fine.  The only thing I could think was to unplug and plug back the DIR-655.  Sometimes that works for a day or a week, but ultimately it always comes back. Is there a setting on the router I can change to avoid this, or a software command I can issue from the computer to clear something?

View 5 Replies View Related

D-Link DIR-655 :: Disconnect Every Few Hours - WAN Just Shuts Off

Jun 4, 2012

Every few hours, the WAN just shuts off.  If you were connected to it when this happens, you cannot reconnect until you have reset the router; you can't even find the SSID.  If you were not connected when this happens, you can connect just fine.  This happens with all devices in the house, my laptop, my DAP-1522, my cell phone, and my brother's Mac (SMH, sometimes I think we aren't related...).  I am running version 2.00NA on B1 firmware. 

View 3 Replies View Related

D-Link DIR-655 :: Connecting A Network Attached Storage Drive?

Dec 10, 2011

I recently purchased a NAS enclosure to use my WD IDE hard drive as a networked drive.  I configured the hard drive's jumper setting as single (no jumper).  I installed the hard drive in the enclosure and connected the Cat 5e cable to the back of the DIR-655 router.  When I tried mapping to the drive, I receive the error:

\STORAGE-3B25 is not accessible.  You might not have permission to use this network resource.  Contact the administrator of this server to find out if you have access permissions.  Network error (1208).

I suspect perhaps that I might need to change a setting on my router to allow me to access the NAS.  The NAS ip address is visible on the router's admin page and I am able to see it when searching for network drives in my laptop.  But I just somehow can't connect to it.  I am running Windows 7 Professional 32-bit.

View 14 Replies View Related

D-Link DCS-942L :: Set Network Drive As Storage Folder?

Jan 24, 2013

I would like to turn on continuous video recording and have it sent to a drive on the same network as the camera without going through a computer.  Is there a way to setup the "storage folder" as a network drive?  For example my network drive is accessed at \192.168.0.1volume1 through a web browser.

View 1 Replies View Related

TP-Link 300Mbps Wireless :: WR1043ND USB Drive Network Sharing Password Bug

Nov 12, 2012

Region : Australia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n

I just upgraded from my factory default and found network sharing of my USB HDD was no longer working.It came down to two bugs in the latest firmware:Even though there is now the option to share without a password that option does not work and you still need a password.And that password is the factory default of "admin" even though I have set my own password.

View 1 Replies View Related

Transfer Large Files Over A TP-Link 340G Mapped Network Drive Get Corrupted?

Feb 17, 2011

I have a Gaming Computer, with a 2x2TB RAID-1 setup, which I use to store .iso files ripped off my game's / movie's disks..Most of the time I'm on my laptop, I have set up a Network Drive to this RAID-1 setup, but when I try to transfer files from the Gaming Computer to my laptop via a network connection, either by wireless G, Ethernet 100mbps, or Ethernet 1gbps, my files get corrupted, this usually happens to larger files e.g over 1GB..But when I transfer the same files to my external hard-drive the files work properly....My computers is networked by a TP-Link 340G....

View 4 Replies View Related

Atheros AR5007EG Wirelss Network Adapter Shuts Down

Mar 9, 2012

My wifi network adapter (Atheros AR5007EG wirelss network adapter) works just fine for about 50 minutes and then it shuts down and disappears as if it's not installed on the computer. To make it work, I have to shut down the computer and turn it on again.

View 7 Replies View Related

D-Link DIR-655 :: Finding Wireless-N Router With USB Drive Share?

Dec 11, 2010

I'm looking for a wireless-N router with USB drive share, those are my only requirements. I was looking at a D-Link DIR-655.

View 11 Replies View Related

Difference Between Map Drive And Network Drive?

Jun 5, 2011

what is the difference between network drive and map drive?

View 1 Replies View Related

Accessing Network Drive From Behind Sub-network Router?

Jun 17, 2011

I am connecting the router to a corporate network that assigns "real" IP to it (DHCP). Then I have 3 computers connecting to this router (local IP 192.168.1.2-4).Assuming I want to access a network drive named "ADrive" (on the same corporate LAN) from any of those 3 PCs, how do I do it? ("\ADrive" does not work, neither does replacing the network drive name with its IP, cannot ping either - it's like I'm on a totally separate network).

View 3 Replies View Related

Internet Shuts Off After Connection To Router?

May 30, 2012

I'm currently using a MI424WR Rev F router, with a Motorola SURFboard SB5120 cable modem.If I connect directly with the cable modem to the PC, the internet works perfectly fine. But the issue is I have 3 connections, (2 wireless, 1 wired)Okay when I connect my modem to the router (Ethernet into WAN, blah blah) the modem suddenly loses signals. I've noticed this on the modem's status page. (192.168.100.1)The downstream power level would constantly change, and the modem will lose the Known CPE MAC Address. (When connected to the router)In order to fix the problem, I would need to connect directly to the modem and reset to the factory settings and wait out the 30 minutes.

here's my current status:

2 Coax Splitters
Comcast Cable Provider
A Verizon Router (Capable until this point)

View 1 Replies View Related

DIR-655 Xtreme N Router Shuts Off With Computer?

Feb 8, 2012

My problem lies with my router shutting off when my computer goes to sleep or is shut off in any way. I even tried unplugging it, which is not good at all for it. I use my router for several other wireless devices so this is bad. I use a Motorola modem that fits to a D-Link router. The modem appears to stay on when I'm having trouble. the route5r is a "DIR-655 Xtreme N Gigabit Router"

View 6 Replies View Related

Tg582n Router - How To Link External Drive To Make Wifi Hard Disc Store

Nov 20, 2011

I have a new techni colour wifi router TG582n which has a usb cobnnection in the side. I also have a new Samsung 400 gig external hard drive can these be linked to make a wifi hard disc store.

View 2 Replies View Related

TP-Link 300Mbps Wireless :: TL-WR1043ND Router Doesn't Show 1.5tb External Hard Drive

Jan 6, 2013

Region : UnitedStates
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
ISP : WR1043ND

The router is not showing my external hard drive in the usb settings. The Hard drive is a seagate 7200rpm 1.5tb. The hard drive works just fine when plugged into my computer. I have tried NTFS and EXFAT. My 2gb usb drive in FAT32 shows up just fine. The external has its own power supply. Is there anything I am missing that would cause it to not work?

View 5 Replies View Related

TP-Link 300Mbps Wireless :: Create Firmware For Hard Drive 4 TB Connection To Router TL-WR1043ND Via USB

Jan 16, 2013

Region : Russia
Model : TL-WR1043ND
Hardware Version : V1
Firmware Version : 3.13.12 Build 120405 Rel.33996n

can You create firmware for Hardrive 4 TB connection to router TL-WR1043ND via USB.

View 2 Replies View Related

Run Server Off Network - Hard Drive Attached To Router?

Mar 27, 2011

I want to know if it is possible, and how is so, to run a server OS or any hosting software from a hard drive that is networked and attached to my router and not to a computer? I currently have a mixed home network of OSes, Mac OS X SL, 2 Windows 7 machines, and various tablets and smartphones. I have a 2TB hard drive attached to an Apple Airport Extreme Base Station (current generation.) The main thing I want the server for is to host for media, iTunes. The Home Sharing function is kosher for in home network use, but I would like to be able to access my media on from outside as well. Optimally I would love to have OS X server on just the drive

View 1 Replies View Related

Cisco VPN :: Mapping Network Drive On WRVS4400N Router

Mar 13, 2011

I have a WRVS4400N router and have successfully connected via Quick VPN Client 1.3.0.3 from my laptop running XP.  I can ping any IP on my network, I can access HTTP addresses and remote desktop (VNC) applications but I cannot map a network drive.
 
The network drive is on a PC running XP, I have tried mapping using the system name as well as the ip and neither work.  There are no problems mapping the drive(s) when connected directly to the router LAN/WLAN.

View 1 Replies View Related

Netgear Wgr614v9 / Access To Network Drive Behind Client Router

Jan 24, 2011

i currently have a netgear wgr614v9 running the most recent firmware update and a tplink nr741nd running the latest dd wrt firmware.the netgear is my main router connected to the modem positioned in the living room attached to this is a wired ps3, wii and various laptops connect wirelessly to this. In my bedroom i have the tplink router is is setup as a client on the netgear router allowing media network drive access to the internet.

eg.
--- wired
~~~ wireless
modem-----netgear~~~~~~tplink----network drive

What i would like to achive is to be able to connect to the netgear router wirelessly and have access to the network drive attached to tplink router.I have tried a client bridge on the dd wrt firmware but this does not work at all. I have read that i need to setup a VPN on the dd wrt but i can find anything on how to do this when trying to access a drive on a second level.

View 3 Replies View Related

Netgear N300 Router / Windows 7 - Setting Up Network Drive

Mar 23, 2013

I've setup a home network using Netgear N300 wireless router (using Windows 7).

I'm trying to get one of my hard drives to be available on the network, so I went to the "sharing" tab of the HD's properties setting and allowed sharing on the HD and turned off password protection so that you don't need a password to access the HD.I also set the permissions to give full control, change, and read access to the "Everyone" group.

From another computer in the network, I tried connecting to the network HD but ultimately got "Access denied" despite the fact that I gave full control to "Everyone".How do I get the computer to be able to connect to the shared HD?

View 2 Replies View Related

Linksys Wireless Router :: WRT54GH Shuts Off Periodically?

Nov 4, 2011

Firmware version is V1.0.01 b001 my WRT54GH has recently started to shuts off periodicaly without any reason. Will stay off for couple of minutes, then will turn ON again. In this period, On/OFF button has no effect.

View 4 Replies View Related

Sharing :: New Wireless Router Doesn't Connect To Shared Network Drive

Oct 25, 2012

Our previous wireless router (Netgear Rangemax wpn802) died yesterday so I went out and bought a Western Digital My Net N900. The issue is that now anyone using the wireless signal can't connect to a shared network folder that they were previously able to connect to using the old router.

I'm not able to log into the old router to see any of its settings. I do have access to the server that has the shared folder - I just don't have any idea what needs to be set in order for the N900 to allow me through to the shared folder - whether it's on the router side or the server side.

[code]...

View 14 Replies View Related

Linksys Wireless Router :: E4200 USB Hard Drive Network Visibility

Nov 4, 2011

I have an E4200 with a 500GB WD hard drive attached to the USB port.  I also have 3 computers on the network named "THINK", "PC", and "DELL". THINK is mixed Wired and Wireless - depending on what I'm doing - Win7 Professional, DELL is plugged into a Range Extender. (RE1000) - WinXP (This one isn't as important: It's an older machine) PC is always hardwired. - Win7 Ultimate, Recently, THINK has unable to see DELL, OR even the HD connected to the router, but it can see PC.  It can also see the HD as a media device - just not as a computer or device I can browse as it does on PC.However, PC can see everything:  THINK, DELL, AND the HD and can access them all the way I would like it to be. Also - MY PS3 DOES see the Media Share and can access it. Edit:  Also just discovered both internal and external FTP no long works. Why can't THINK see the HD connected to the router regardless if I'm wired or wireless?  As far as I can tell, all the settings are identical on both THINK and PC. Is there a router setting I'm missing?  IPV6 is disabled and I've treid the basic disabling of HOMEGROUP and anything that goes with it - but nothing yet.

View 9 Replies View Related

Linksys Wireless Router :: WRT610N Network Drive Can't Be Accessed By Any Computer

Feb 27, 2013

I have a WRT610N v2 with current firmware.  The hard drive is a Western Digital Elements formatted to NTFS and already has music and photos so that other computers in the house can view them. This setup was done awhile back, maybe even a year ago.
 
Anyway, I can map the network drive and see everything there, but then after awhile (minutes - maybe 10) of idle time, the network drive can't be accessed by any computer, either as the mapped drive (W or by clicking the WRT610N in the network tree. It's like it goes to sleep and can't be awakened by activity.
 
I have searched the forums here and at WD but haven't found a solution or even this exact problem.  I did find a utility on the WD site that is supposed to fix/eliminate the short idle time, but it didn't seem to work.

View 4 Replies View Related

Linksys Wireless Router :: WRT610N Shuts Down And Needs To Be Manually Powered Up?

Aug 23, 2011

I recently upgraded my WRT610N to Firmware Version: 2.00.01 and now the unit powers down on its own after a few hours.  Are there any known issues with this firmware?Is there any way to roll back to the previous version of the firmware?

View 4 Replies View Related

Belkin Play N600 Exposing USB Hard Drive Attached To Router Within Sub-network

Aug 30, 2012

I recently purchased the Belkin PLAY N600 router to create a private network for my home theatre setup.I have a primary home network 192.168.0.x (NetGear) which I use for all my computing needs. I extended a network cable to my Home theatre area and plugged in the N600 router. After this, I attached a USB external hard drive to the router and it works great. I can see it from the 192.168.2.x home theatre network (Belkin).I would like to expose the USB hard drive hooked to the Belkin Router to my primary network so that I can copy over my music and pictures without having to physically move the hard driveonto a PC connected to the primary domain.The Belkin router has a DMZ function which exposes an IP on its internal (192.168.2.x)network to the external (192.168.0.103) network.Is it feasible to expose the USB drive to my primary home network?

View 1 Replies View Related

Linksys Wireless Router :: Ea3500 Bridged Mode And Windows Network Drive?

Apr 5, 2013

I'm runing an ea3500 in bridged mode, classic configuration, firmware 1.0.30 build 126544. I got ftp working for my usb attached wv delements drive , but it is totally invisible in windows (except for ftp of course).I read in an older post that the usb drive in certain situations does not work (independent of disk manufacturer/type and such) and for certain configurations the ftp option might work but the windows mapped network drive doesn't , does that still apply? does it apply to bridged mode ?

View 1 Replies View Related

Linksys Wireless Router :: E4200 V2 Error Modifying Folders On Network Drive?

Apr 22, 2012

I have the e4200 v2. I had a hard drive attached to the router. When I try to add files to folders on the drive, sometimes I can add files and sometimes I can't. It is a folder by folder basis. I can't seem to change any security setting that will let me add files to certain folders on the drive attached to the e4200 v2. 

View 6 Replies View Related

Linksys Wireless Router :: EA4500 - Network Drive Only Works Without Secure Folder Access

Feb 2, 2013

I'm trying map the USB hard drive connected to my EA4500 router as a network drive in Windows 7, and it works perfectly until I enable secure folder access on the router.
 
After enabling secure folder access, and not changing any other settings on the router I first unmount the drive since it was set up without credentials and doesn't work that way any more.  When I try to remap the drive I use the same address, but select "Connect using different credentials"  When it prompts me for the log in info I try using the router admin account, but it fails to connect.   Windows network diagnostics tells me the device refused the connection.  I proceeded to set up an account on the router under the folder access settings with the same username, and password I use on my computer, and tried to connect it without checking "Connect using different credentials" (And typing them in manually if that matters) with the same results.
 
Even with secure folder access enabled I can still reach the drive just fine by typing "ftp://192.168.1.1/" into file explorer.  It prompts me for a username and password, I put in the admin credentials, and I'm in.  Even the account I created with the same username/password as my computer works this way.
 
After disabling secure folder access everything works perfectly fine again...  I would MUCH rather do this with it though.
 
Following these directions: [URL] When clicking the browse button the router shows up when secure folder access is disabled, but does not after it is enabled.  I've looked through my windows sharing settings, and haven't noticed anything that should cause problems, pretty much everything is enabled.  I've also tried turning off my firewall with no success.

View 7 Replies View Related

Linksys Wireless Router :: E4200 Would USB Port Connected To Hard Drive Still Function As Network Storage

Jan 14, 2012

If I were to take a e4200v2 and use it as an access point (disable DHCP), would the USB port connected to a Hard Drive still function as network storage?

View 5 Replies View Related

Home Network :: Mapped Network Drive Not Reconnecting On Bootup?

Nov 18, 2012

I have a windows 7 desktop with an SSD and regular mechanical hard drive where I keep my data. I also have a laptop with a small SSD as well. I wanted to keep the laptop free of non-critical data so I decided to setup a file share between my desktop (Windows 7 home prem) and my laptop (Windows 7 pro). I was able share the files and navigate to my desktop through my laptop. I successfully mapped the folder as a network drive and all was well. Then I rebooted and I was disconnected from it, it remembered that it was there but I needed to manually connect to it and I needed to provide my login credentials. There is no password just a username.

What is causing this and is there a way to get around this? Also is there a way to set a timeout because if my desktop is not on and I want to use my laptop, the boot times are much longer compared to when I don't have the mapped network drive on my laptop at all.

View 1 Replies View Related

LaCie 5big Network 2 Drive No Longer Shows Up On Network?

Aug 11, 2012

I'm trying to see if I can fix my friend's NAS which apparently has some pretty important data on it that wasn't saved anywhere else. They actually had the Geeksquad look at it and they've come to the same conclusion I have so far, but I figured I would ask the internet before I gave the thing back to them and said Geeksquad was right.

Anyways, they have this 5 drive RAIDed NAS which apparently just stopped showing up on their network. I borrowed it from them to see if I could figure it out. It turns on just fine and my router assigns it an IP address, but the IP address just takes me to a blank LaCie dashboard screen. It's weird because it's clearly running it's web server because it's just a gray background with an empty white box and "(c) LaCie 2010" at the bottom. No content at all.

Additionally, I tried installing the LaCie Network Assistant on my home computer and it says it cannot find any network disks. I've tried the "wake up a device" where I enter the mac address, but that doesn't do anything.

All the lights are solid blue on the front and over all the drives so it doesn't appear a drive has failed or something. Even so, that wouldn't really explain the blank dashboard right?

View 1 Replies View Related

D-Link DIR-601 :: Laptop Without CD Drive / Still Possible To Connect To Internet?

Jun 17, 2011

I just got this router and it is working with my pc. wireless internet, however is not working despite trying to connect through a USB drive. My laptop which is what i'm trying to connect to the internet from is not picking up my server, and i'm wondering if the problem is that I have not used the cd that came with the router. My laptop does not have a cd drive and I do not have a portable drive to connect it to.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved