I would like to turn on continuous video recording and have it sent to a drive on the same network as the camera without going through a computer. Is there a way to setup the "storage folder" as a network drive? For example my network drive is accessed at \192.168.0.1volume1 through a web browser.
View 1 RepliesAnyone using it to save videos from their cams? Are you using Synology NAS? Am interested and want to hear from people qualified to discuss NAS. Qualified means you are currently using NAS or have thoroughly researched it to the point you have made your purchase decision for the most part.
View 6 Replies View RelatedI'm trying to share all of my Itunes media (music, movies, apps, etc.) between three PC's. I have created a share of the entire hard drive which I have mapped on all three computers. Basic connectivity seems to be working fine. From each computer, I am able to read and write to the disk. In Itunes however, I created a library including everything I want to share, but Itunes is unable to save the library.When I check security options on the hard drive, I see that it is owned by an unknown user and I am unable to change ownership of the drive. The owner is listed as "Account Unknown S-1-5-21 plus a long string of numbers) I think that if I can take ownership of the drive, I can get iTunes to save the library. how I can change the account ownership of the storage drive? Trying to change ownership properties, I get an access denied message.When the drive is connected to a PC via USB, I am able to change its ownership, but it reverts back to the Account Unknown owner when connected to the router. All three computers are running Windows 7 64bit.
View 5 Replies View RelatedI recently purchased a NAS enclosure to use my WD IDE hard drive as a networked drive. I configured the hard drive's jumper setting as single (no jumper). I installed the hard drive in the enclosure and connected the Cat 5e cable to the back of the DIR-655 router. When I tried mapping to the drive, I receive the error:
\STORAGE-3B25 is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Network error (1208).
I suspect perhaps that I might need to change a setting on my router to allow me to access the NAS. The NAS ip address is visible on the router's admin page and I am able to see it when searching for network drives in my laptop. But I just somehow can't connect to it. I am running Windows 7 Professional 32-bit.
I have a Windows 2003 SP2 server with a shared folder. This folder is accessed by 2 people on a regular basis. The problem we are experiencing is when a folder is created by user A, it cannot be moved by user B (and vice versa), as it says the folder is in use.The exact error is: Error Moving File or Folder.Cannot move <filename>: Access is denied.Make sure the disk is not full or write-protected and that the file is not currently in use.I have explicitly set full control for both users on the folder. The drive has 70GB of 500GB remaining. I have also used File Server Management to verify the files were not in use when they were being moved.The server is Windows 2003, SP2. Domain environment, with all relevant users having permissions on the folder, and the everyone account removed. Any other operation inside the shared folder works fine.
View 2 Replies View RelatedI'm trying map the USB hard drive connected to my EA4500 router as a network drive in Windows 7, and it works perfectly until I enable secure folder access on the router.
After enabling secure folder access, and not changing any other settings on the router I first unmount the drive since it was set up without credentials and doesn't work that way any more. When I try to remap the drive I use the same address, but select "Connect using different credentials" When it prompts me for the log in info I try using the router admin account, but it fails to connect. Windows network diagnostics tells me the device refused the connection. I proceeded to set up an account on the router under the folder access settings with the same username, and password I use on my computer, and tried to connect it without checking "Connect using different credentials" (And typing them in manually if that matters) with the same results.
Even with secure folder access enabled I can still reach the drive just fine by typing "ftp://192.168.1.1/" into file explorer. It prompts me for a username and password, I put in the admin credentials, and I'm in. Even the account I created with the same username/password as my computer works this way.
After disabling secure folder access everything works perfectly fine again... I would MUCH rather do this with it though.
Following these directions: [URL] When clicking the browse button the router shows up when secure folder access is disabled, but does not after it is enabled. I've looked through my windows sharing settings, and haven't noticed anything that should cause problems, pretty much everything is enabled. I've also tried turning off my firewall with no success.
If I were to take a e4200v2 and use it as an access point (disable DHCP), would the USB port connected to a Hard Drive still function as network storage?
View 5 Replies View RelatedHave just had a stab at using my Netgear DGND3700's USB drive sharing - I had a spare external HDD + I want to be able to access files on it both over the 'net and from local network. Both work fine, very easy to set up, however I am unable to edit settings for the shared folder, which means I am unable to password protect it.
I don't need a password for local sharing but obviously it isn't ideal to have files freely available on the Internet, have looked into troubleshooting but can't find any similar stories with Netgears.I click "edit" or "create network folder" and it loads for a second or two but just stays on the same page. There is only one option to select but I have tried clicking the radio button first anyway, then clicking edit, same result.
I have my 942L set up for continuous recording. When I look at the files, the camera will record between 20 and 55 seconds, end that file and start another. The next file then starts between a few seconds and as much as 40 seconds later leaving a gap in the video recoding. The file sizes are all different and the amount of record time is different for each file.
Also, about 80% of the time, the time increments a few seconds on a playback and then stops updating even though the video is longer.
I just got the camera today, looks good, works good, at least so far.. BUT I was SURE this camera had a battery and charge function!? What's the point of having this camera if I can't place it say inside my car or in the garage (where it needs to be hidden, alas I can't use any cords!)?
View 5 Replies View RelatedI have an externaL free Agent Hard Drive that I have a corrupt folder on. I would first like to fix it but if not possible I would like to delete it.
View 1 Replies View RelatedI am using Win 7 Pro x32. When I use RDP to connect to another computer, I noticed that on the remote computer (sometimes) as well as on my local machine (always), it creates a "Z:" drive. It isn't like a mapped network drive though, it shows under Hard Disk Drives. The free space is the same as the C: drive. When you open it, it is the %TEMP% folder on my machine. Going to the run command and typing %TEMP% will show you the same contents as the Z: drive. When I close the RD Connection, the Z drive goes away. I have no clue what is causing this and I did a little searching and couldn't find anything that resembled anything close to this online. I saw the same thing happen on a Win XP machine earlier as well.
View 1 Replies View RelatedI seem to be struggling to connect more than 4 cameras to my (ISP-supplied) modem/router by Netgear CGD24N via WPS. I'm on my 5th camera now (already have 3x 930L and 1x 942L) but the newest 942L just won't connect to the network at the moment and there's definitely no faults here as I swapped cameras today at the local retailer (and got an A3 942L!).I've even tried connecting the camera to my wireless extender (Netgear WN3000RP) but no luck there.
So far it has only worked twice for short periods of time (enough for me to configure the cameras) but since then I can't actually get it working. I've got a couple of spare wireless routers lying around too and should be receiving a DIR-600 soon (from the Netgear promotion in Australia) which could be useful?
when an external hd is connected to the e3000 via usb, that i can read and write to it, but i cannot delete files from the external drive? i have been trying to figure this out for a while and cannot delete files after i write them.
View 3 Replies View RelatedI have a desktop and a laptop. I'm trying to share my external HD from my desktop, to my laptop.What I did was gave the local administrators group full share permissions to the drive, and of course the local administrators group also has full NTFS permission.That being said, I went to my laptop and did a Code:net use X: \mydesktopexternal /user:mydesktopuser PasswordExternal is the share name for the external HD on my desktop. The command worked successfully, however, I am still getting Access Denied when trying to get inside of this mapped drive.How and why does the command map the drive properly, using those credentials, but there's no access when trying to navigate to it? It works if I give Everyone full share permission, but I don't want anyone to just connect to it. Use password protection file sharing is enabled, but of course with "Everyone" given permission, that won't apply (at least to my knowledge).
View 7 Replies View RelatedI have a new apple airport extreme wireless router and have done all the port forwarding and gave the camera a static address and cannot view my camera outside my network. I also have done the dyndns service also. I will note if I change the http port in the camera settings to say 82 I get a black screen and cannot view my camera till I switch back to port 80. Reason why I want to do this is I need to view my camera for more then 60 seconds.
View 5 Replies View Relatedi have both 932L and 942L and the 932L was plug N Play and no problem setting up with my WiFi. But i can't get the 942L to work. Works fine with the Ethernet cable but not wireless.
Come on ... I can't be the only one with this problem? I have two 942L cameras and neither one of them can I get connected to the wireless network.
I want to share any folder or drive only one user amongst 20 at windows xp.How?
View 1 Replies View Relatedi set-up the D-LINK DNS 323 NAS unit with RAID 1 (dual 2-terabyte 5400 rpm drives) it works, but it is slow in copying files between my computer and it (8 minutes to copy 4.5 gig file between NAS and my PC). i am using Cisco WRT160N router. replaced the network wires to the latest spec, and my computer has realtek PCIe GBE network adapter.
View 1 Replies View RelatedI tried several times to see the DCS 942L camera picture on my Samsung Advance S smartphone on UMTS 3G net but also setting the video parameters profiles at minimum (64 Kbit/s) it does not work. The MyDlink lite version is the 2.6.1. release. Locally ,using Wi-Fi it works well of course.
View 5 Replies View RelatedJust got this & set it up today. Wanted to buy a couple more in the next few days; but wanted to test out the D-Viewcam service. The application (D-Viewcam) is not able to find my camera.I have 'ticked' the uPNP & the forward; tried to disable it as well. No luck.
Camera 942l is on ver 1.1
D-Viewcam = v 3.2
Both reside on the same LAN
I'm able to view the camera on the browser. And on my phone.
I just upgraded my wireless router to a D-Link DIR-655. I have 2 PCs and a network storage device (D-Link DNS 321) connected via ethernet to the router. I also have an xBox 360 connected wirelessly to the router. The xBox is able to connect to the internet via the router, but it cannot connect to (see) the PC's or the network storage device. It was able to do so with my old wireless router (a Belkin), but it stopped with the DIR-655.
View 4 Replies View RelatedI have four DCS-942L cameras and a 2012 model Airport Express router. I cannot view live video from outside the router in any fashion other than mydlink.com's poor quality time-limited forwarded video. Here is what I have done.I have manually mapped four TCP ports through the router for accessing the cameras' web servers. This works--I can access the camera settings that way, albeit with NO SSL support (dammit). So, fundamentally, port forwarding works on this router. The "live view" accessed through the camera's web server does not work, though.I mapped port 554 on each camera to ports on the WAN side of my router, TCP and UDP.I have made sure that the external ports set on the camera under "Enable UPNP port forwarding" are the same as the external ports set on my router. (Otherwise the web server wouldn't work from outside.)When I access the mydlink web site from inside the LAN, I can view my video. When I run netstat -n -p tcp, I can see connections open to the local 192.168.0.* addresses of my cameras, so it is connecting via the LAN.If I connect to the Internet outside my LAN, and use the mydlink web site, I get the forwarded, mini-sized video with a 60 second limit. netstat reveals that connections are being attempted to the INTERNAL ip addresses of my cameras, which of course cannot succeed from outside. In addition, if I try to stream video using QuickTime Player from outside, using the URL [URL], the player connects, then says "waiting for stream" and then "switching transports." It gets stuck there and does not proceed. On the LAN, using the local IP address, I can stream video just fine.
Any way to change this?What other ports do I need to open to make the video stream work? I tried mapping ports 5556-5559 to one of my cameras, but that did not work. Also, I have four cameras and need to be able to map to all of them for this to work.The AirPort Express supports "NAT Port Mapping Protocol" which, from my limited research, is not the same as UPNP. How to successfully viewed video from outside a router without using UPNP?I have scoured these forums considerably and have read some success stories using UPNP. From the DCS-942L manual, it seems like I should be able to set up manual port forwarding in some fashion to make the video stream work. Clearly, though, some auxiliary connection is being attempted and the client cannot get through to the camera. Is it possible to even pick this statically, or is the port always dynamically chosen by the camera and therefore absolutely must be set up on the router using UPNP? If I can't make static port forwarding work, then these cameras are headed to camera heaven soon.
I have the Dlink DIR 615 router, windows 7, and this morning, it suddenly started to shutdown and restart, over and over. I unplugged all ethernet connections, shut down, etc. and slowly added the PC, then the phone, until when I plugged in the Western Digital 2TB My Book live, it would begin the same restart process. I can now repeat the issue by unplugging, and replugging the drive. I have had the network drive for about 3 months, and this started today.
View 6 Replies View RelatedRegion : Australia
Model : TL-WR1043ND
Hardware Version : v1
Firmware Version : 3.13.12 Build 120405 Rel.33996n
I just upgraded from my factory default and found network sharing of my USB HDD was no longer working.It came down to two bugs in the latest firmware:Even though there is now the option to share without a password that option does not work and you still need a password.And that password is the factory default of "admin" even though I have set my own password.
I have a Gaming Computer, with a 2x2TB RAID-1 setup, which I use to store .iso files ripped off my game's / movie's disks..Most of the time I'm on my laptop, I have set up a Network Drive to this RAID-1 setup, but when I try to transfer files from the Gaming Computer to my laptop via a network connection, either by wireless G, Ethernet 100mbps, or Ethernet 1gbps, my files get corrupted, this usually happens to larger files e.g over 1GB..But when I transfer the same files to my external hard-drive the files work properly....My computers is networked by a TP-Link 340G....
View 4 Replies View RelatedI have 1.00 build 0522 and searching the support website I see no link. But reading here I see there is a later version.
View 1 Replies View RelatedThe company has a glitch that they are not sure if they will fix so you can't record with mac. I am unable to return my cameras to staples and Im out the money for the memory cards I opened. It says you can record with MAC clearly on the box!!!! Bad business practice for STAPLES and DLINK.
View 3 Replies View Relatediphone and android app but no blackberry.
View 3 Replies View RelatedI just purchased 2 cameras and have one set up.
Firmware V 1.12
Works great on my android phone and connects fairly quick. When I try to see the camera image on my PC with windows 7 64 bit, I log into my d-link and it shows the camera name on left side of screen, then says Java run time environment not installed.I uninstalled java 5 times and re installed both 32 and 64 bit but keeps coming back as not installed. Camera is set up wirelessly through a Belkin router, so far no EZ config
Is there such a possibility in the firmware or through telnet?
View 3 Replies View RelatedAs DCS-942L IP cam is compatible with "NVSCGI APIs" (search this string on a search engine and you will find some useful PDF docs), many features of this IP Cam may be enabled or disabled using any web browsers, for example we can manage the motion detect.
[url]....
I just bought new 942L (HW Rev3, 1.12 FW) and the only profile which is used to stream to iPhone or Web browser in mydlink is profile 3 which is limited to JPEG. Is there some way how to change the profile to be used for streams or is there a way how to make to profile 3 something else then JPEG?
View 1 Replies View Related