i set-up the D-LINK DNS 323 NAS unit with RAID 1 (dual 2-terabyte 5400 rpm drives) it works, but it is slow in copying files between my computer and it (8 minutes to copy 4.5 gig file between NAS and my PC). i am using Cisco WRT160N router. replaced the network wires to the latest spec, and my computer has realtek PCIe GBE network adapter.
View 1 Repliesi set-up the D-LINK DNS 323 NAS unit with RAID 1 (dual 2-terabyte 5400 rpm drives)
it works, but it is slow in copying files between my computer and it (8 minutes to copy 7.94 gig file between NAS and my PC via wire).
i am using netgear WNDR3700 gigabit router. replaced the network wires to the latest spec, and my computer has realtek PCIe GBE network adapter.
this is looking more and more like the NAS RAID 1 is the bottleneck.. possibly 7200 RPM drives would have kicked more ass?
i have a newly formatted (i.e. empty) 2TB WD my book elite which when i connect it to my computers usb port, can transfer a 6gb video file at over 100MB/s according to the win 7 detail box. However, when i connect it to the usb port on the back of the e4200 and try to transfer the same file, it only goes at 8MB/s max ... it appears to be going at usb 1 speed. i've got the latest firmware on both the e4200 and the my book 1111 and everything seems to be working fine for both, except this transfer rate when connected to the e4200.granted, cisco doesn't specifically list this drive as being tested, but the router does recognize it and shows it as usb 2.0, but yet the transfer speed is just too slow.8MB/s is just not workable...i could just connect the drive directly to the computer and share it that way, but connecting it to the e4200 was one of the reasons i bought the e4200.
View 8 Replies View RelatedRegion : Russia
Model : TL-WDR3600
Hardware Version : V1
Firmware Version : 3.13.23 Build 120820 Rel.73549n
ISP : VIMPELCOM
I have portable hard disk connected to one of the TL-WDR3600 router usb ports (another one has printer connected to it)
Write speed is about 3Mbytes/sec maximum.Real disk write speed is about 35-38Mbytes/sec - if I connect it to one of the PC USB ports (both router and PC ports are USB 2.0)Why write speed via router is so low?
My PC is connected to router via cable and is running Windows 7 32bit Ultimate SP1, hard disk partition is 465Gb NTFS single volume.I'm measuring speed simply by coping 1.4Gb file through Windows Explorer to \tplinklogin.net (following USB storage access instructions from router control panel) in first case and directly to hard disk - in second case.
wr2543ND / very slow shared storage transfer speeds?
View 4 Replies View RelatedI live in the tampa bay area, I have bright house (BHN) as my service provider, which provides a Road Runner Lightning (40/5) package. I previously used BHN's top tier (20/2) back in July (and prior) with no problems.
After converting to Lightning in August of this year (2010). Of course, BHN (and every other provider) wants to force a modem/router down your throat, so I had them bridge it (in short, turn it into a dummy modem with no routing). I had an SMC branded modem gateway at the time. I work from home 2 days a week (so I can spend more time with my kids during morning, lunch, right after work) and this requires me to use QoS to ensure my VOIP work calls don't get dropped, if the family is watching youtube videos or watching netflex.
My network was as follows SMC Modem >WAN IP>>WAN Port>>D-link DIR-655>>Switch Ports>PC1, PC2, PC3
Everything seemed fine (from a usability stand point) till about 2 weeks ago when my upload speed seemed to grind to halt. Normally I was able to upload about 200-300K per second, and I noticed this dropped to about 45K per second during a drop box upload. First thing I did was power cycle both my modem and router (in the proper/usual order). After they both come up, I start using speed test to find out what my upload speeds were. I was getting about 39Mbps down, but only .56Mbps up still. I factory reset my router.... test, similar speeds. Power cycle all computers (just in case), and then modem/router. Tested, similar speeds. Updated the firmware to the latest. Same issue
Called BHN customer service, they factor reset it, but it wasn't in bridge mode. If I by passed the 655, in factory mode (non bridge mode) upload speeds returned to better than expected states. If I bridged the cable modem, upload speeds seemed to crash.
Had BHN replace the modem, seemed fixed for a day, then issue came back. Had them come back out and replace it again, this time with a Motorolla Surfboard modem... same issue. Fine during factory reset, however after they bridge the modem, upload speeds were fine. Told BHN I would take it from there.. Connected up the DIR-655, and upload speeds crashed again. (.6Mbps). Called D-Link Support, and the Chinese English speaking rep seemed to not be listening to me and tried to have me adjust my MTU as well as Wireless settings. Long story short... the rep was a level 0 id10t and I hope D-link will consider hiring better employees/contractors. So I was all about to give up and replace it with a DD-WRT capable router (which it takes me a lot to want to swap hardware), when I discovered the wan shaping was on. Which I thought to myself... nah... QoS has never messed up before... why would it be the cause. Turned off wan shapping... and voila. Issue seemed to be insta-resolved.
Unsatisfied with that... I decided to dig a lil deeper. I turned on Wan shaping again, but decided to set the settings manually instead of auto detect.
Here are the settings I used... (Advanced Tab>QoS)
Enable Traffic Shaping - Checked
Automatic Uplink Speed - Unchecked
Manual Uplink Speed - 5000
Connection Type: Cable or Other Broadand Network
Enable QoS Engine - Checked Automatic Classification - unchecked (this checked seemed to affect my upload speed by about 5-10% during testing) Dynamic Fragmentation - unchecked (this checked seemed to be the worse enemy for upload speed)
While I know I'm not any network guru (still have to use a subnet calculator for subnetting), I think I did a pretty good job drilling down the issue (once I got passed my service provider replacing modems).
Anyways, I've had overall good luck with D-Link products, even have a 5 port 10/100 switch (all metal) from 1998 that works great. Hopefully, D-Link will just either put more documentation on the web, or hire better employees.
Anyone using it to save videos from their cams? Are you using Synology NAS? Am interested and want to hear from people qualified to discuss NAS. Qualified means you are currently using NAS or have thoroughly researched it to the point you have made your purchase decision for the most part.
View 6 Replies View RelatedI just upgraded my wireless router to a D-Link DIR-655. I have 2 PCs and a network storage device (D-Link DNS 321) connected via ethernet to the router. I also have an xBox 360 connected wirelessly to the router. The xBox is able to connect to the internet via the router, but it cannot connect to (see) the PC's or the network storage device. It was able to do so with my old wireless router (a Belkin), but it stopped with the DIR-655.
View 4 Replies View RelatedI recently purchased a NAS enclosure to use my WD IDE hard drive as a networked drive. I configured the hard drive's jumper setting as single (no jumper). I installed the hard drive in the enclosure and connected the Cat 5e cable to the back of the DIR-655 router. When I tried mapping to the drive, I receive the error:
\STORAGE-3B25 is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. Network error (1208).
I suspect perhaps that I might need to change a setting on my router to allow me to access the NAS. The NAS ip address is visible on the router's admin page and I am able to see it when searching for network drives in my laptop. But I just somehow can't connect to it. I am running Windows 7 Professional 32-bit.
I would like to turn on continuous video recording and have it sent to a drive on the same network as the camera without going through a computer. Is there a way to setup the "storage folder" as a network drive? For example my network drive is accessed at \192.168.0.1volume1 through a web browser.
View 1 Replies View RelatedI just bought this router. Unfortunately I'm losing close to 3mpbs !
When I was connected directly to the modem i had a little over 12.5 Mbps
Now I'm stuck at 9.5mbps and it won't go higher!
I read a bit over the forum. I tried turning off the QOS but it didn't change a thing.
Here a little extra information;
My internet provider is Cogeco
MY computer is wired
I tried 2 internet tester, both give me the exact same result
My DIR655 is A4 with firmware v.135.
My normal uplink speed is above 4 Mbps but the speed goes down to 0.4 to 0.8 Mbps. The above unit was received from D-Link as a replacement for the same reason, but it worked for at lease 12 hours.
If the power is OFF/ON cycled, the normal speed comes back but last only about 10 minutes.
Been plauged with some slow speeds lately and decided to check the speeds, with cable in modem i have 4.9 mbps upload but when i go through the router i have 0.3 mbps. Router is relatively new, just a couple months, firmware 8.00.
View 5 Replies View RelatedJust bought a new DIR-655 Xtreme N Gigabit Router 3 days ago. Have 5MB fiber and consistently receive 4.7-5.0MB when connected directly to my laptop (windows XP, Dell wireless 1390 WLAN Mini-card, 802.11g only). I followed the CD instruction to set up the router and when connected wirelessly I consistently get 2.4 - 2.7 MB. When I connect a cable from the router to my laptop, I get the 4.7 - 5.0MB that I get when connected directly. I've tried a second laptop (Vista, 802.11g only) and when connected wirelessly I get 4.7-5.0 MB. A friend of mine who has a laptop (Windows 7, g/n) also connected at 4.7-5.0 MB.
View 1 Replies View RelatedI noticed after setting up the router. My download speed has dropped.
View 3 Replies View RelatedRecently I have noticed my internet get slow. I use a comcast cable internet connection that is directly connected to my dlink DR 655. I use the megapath internet speed test [URL] when testing my internet speed. Have a laptop that is usually on wireless and an XP workstation that is connected to the 655 directly with static IP.
I would be browsing the internet and all the sudden the internet would get really slow. This would happen on both my desktop and the laptop and my speed test on both machines would be around .3 Mbps. When this happens I would go and connect the laptop with the ethernet pot directly to the modem. Of course a reboot of the modem has to occur before a connection can be made so once I do that all the sudden my internet is back up to par (12 Mbps). I go ahead and put my network back to the way it was and it all goes back up to 12 Mbps. I have called comcast several times and they are telling me it my router.
This picture shows a snapshot of some windows from the laptop. The CMD ipconfig on the bottom left shows the laptop network settings when connected directly to the modem. The CMD ipconfig on the upper left is the network settings when connected to the router. The web page on the right shows the WAN network settings when the 655 is connected to the cable modem.
Notice the DNS servers, they are different when the 655 is connected to the modem versus when the laptop is connected to the modem. Could this be part of my problem? I have not seen were I can manually change 655 DNS entries ... is there a way to do this? Or should I not even be worried about it?
I am using a DIR 825 and I experience slow data transfer speed within my internal network under the wireless connection (2.4 Ghz), 2 Mbs. I can videostream from the internet OK, no problems there, but when I want to transfer data between two external HDD (NAS devices) it can get as slow as 2 Mbs.
View 1 Replies View RelatedTransfering from PC to Laptop. This just seems slow. I'm wired to the PC and wireless to the laptop. With a A3 on 1.21 FW
View 4 Replies View RelatedI recently switched from Linksys WRT54G router to MediaLink router. My wired connection speed stayed the same but my wireless speed degraded significantly - roughly from 5-8mbps to 200-300kbps.I measured my wireless speed both on win7 laptop and iPad. My Roku box is also struggling. All devices were in the proximity of the router.I tried changing encryption (WEP/WPA2/no encryption), mode (from b/g/n to b/g to just g), and different channels. Nothing worked, the speed is still very slow.
View 4 Replies View RelatedI recently bought a new TP-Link TL-WR741N, I'm transferring data from my desktop wired network, windows 7 to net book windows xp wireless. i'm getting only 2 mbps.
View 3 Replies View RelatedI`m new here I recently purchased the dir-615. I started configuring with cd but i couldn`t get past the step where it should verify if cables are plugged in , so I did it manually. Some pages won`t load , internet speed is slow ( Both wireless and lan speed ) . I am using a PPPOE connection , I even got my ISP to check my settings, and he said it was alright but it reduces my speed by a lot. Usually I download with 1 MB/s with the router on wi-fi I hardly get 50 kb/s and on lan max is 100 kb/s.
View 1 Replies View RelatedI have recently bought a TP Link wireless usb adapter (TL-WN727N). Initially I had some issues with drivers but solved that and my internet was working perfectly for around 2 days. However recently the internet speed has dropped down to extremely low speed periodically for no apparent reason. I can be downloading something at around 700kBps one moment then only have 100B/s the next. [CODE]
View 3 Replies View RelatedRegion : Denmark
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n
ISP : Arrownet
I purchased a WDR4300 yesterday and have set it up. The internet is running smoothly although the transfer speed is rather slow. When transferring from my computer to my Seagate GoFlex Home i get about 6 - 8 mbps with Wireless N. The router is set to only use Wireless-N and my laptop has the latest drivers. I have also tried other computers in the house and the speed is the same. The GoFlex Home is connected to the router via a LAN cable. Prior to updating i used a Linksys WRT54GL and managed speeds of about 3 or 4 mbps over its G only connection. As for transfers between 2 computes the rate is about 1 - 3 mbps
As for distance the Wireless router is only about 1.5 meters from the laptop (across the room) with nothing in between them to cause interference. I have also checked what channels my neighbors use (using inSSIDer) and picked 13 as there is only 1 other person nearby on that channel and they are quite far away.
Region : Others
Model : TL-WR841ND
Hardware Version : V8
Firmware Version : wr841nv8_en_3_13_27_up_boot(121101)
ISP :
I followed TP-Link's guide to set up a WDS connection between my two brand new WR841ND router. It theoreticaly "works", but the network is extremly slow. Copying a ~100 Mb sized file to another computer on the other side takes more than 10 minutes or more, I don't know exactly, because I shut down the process after 10 min. I pinged the "slave" router with 200 packets, and I realized that every third, fourth and fifth packet has more than 500 ms time. The minimum is 4 ms, the longest was 566 ms.
Router A (Master)
Connects to the internet/ADSL
DHCP enabled
[Code].....
I bought the two router from the same dealer, at the same time. Both have the same firmware. I checked all the chanels, and 5 is the only free one, but the situation is the same on every chanel.
What can couse this very slow transfer speed?
Region : UnitedStates
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 0.10 v0005.0 Build 120516 Rel.45877n
ISP : HiPointInc
Network Status.jpg
I've upgraded my line connection from 4mbps to 20mbps.I've also checked my status with HiPoint and on 192.168.1.1 which is shown on the attachment. No problems.
Max Downstream is 25612kbps but Current is only 4396kbps.Do I need to configure anything? Btw its directly connected to my PC?
Region : Brazil
Model : TL-WR841ND
Hardware Version : V7
Firmware Version : 3.13.9 (Last)
ISP : NET Virtua
I've bought a TL-WD841ND and was using it normally.
After I arrived from a trip, the internet speed by wireless and by cable is only 0,5~0,7 Mbps...
My internet connection is 10 Mbps, and if I plug direct on the modem, there comes the real speed (9,7 Mbps), but connecting by the router, the speed is 1/20 of what should be. Before my travel i was using it normal, and no one has changed any configuration.
So i've updated to the last firmware avaliable on the website. So i've rebooted it and the "configuration" LED keeps flashing...
I would like to know if this led flashing is normal: (here is a video that i've done: [URL] and what could be happening. ps: connecting by cable, the internet speed is also the same (even after the factory settings reset)...
Region : Romania
Model : TL-WR841N
Hardware Version : Not Clear
Firmware Version : Latest
ISP :
i just bought this router, all good until i had to upload wireless over ftp or samba. It is version 8.2
Firmware Version:
3.13.27 Build 120802 Rel.51024n
Hardware Version:
WR841N v8 00000000
I bought this router for the advertised 300 mbs, my last 150 router was giving me 6/7 mbs over wireless upload on ftp. Tp link router is giving me 800 k.
Download works on wi fi , i got 9,3 mbs from a 150 N adapter.
I tried all security options , even mac filtering . And i am trying to ftp over network , not the internet.
every devices on my network started having really slow speed. It takes long time for each to navigate thru sites. Normally every device gets around 20-25 MBPS in the network. And i have desktop, laptop, iphone, tablet on the network. I've been trying to fix this for whole day yesterday and today and no luck.how to fix this?.I ran some things from this site and the results are here.
[code]...
My ISP has increased the speed on their link on my side I got a new cisco 887. I replaced 877 with Cisco 887 and copied all the configuration from Old cisco 877 to new Cisco 887 Router.Now My users can connect to the servers and which are in main office (remotely) and they can access internet everything is fine.
The only big problem is Users are complaining Network is very very slow.Do I need to change any settings on my new router? [code]
When connected to my router on my main desktop, I get download speeds of about .3-.85 mbps, I have comcast and a linksys N router, as well as a N wireless adapter in my desktop. If I use my laptop, I get around 10 mbps download speed, (Speeds are as of [URL]) but they still remain at .3 mbps on my desktop. I have tried two different wireless adapters in my computer. One is the Linksys AE2500 Dual Band N adapter, and the other is an ASUS N13 N Adapter. I have gotten the latest drivers of both adapters, but speeds stayed very low. When I connected the computer via ethernet cable, it ran at 16mbps. So I think that something must be wrong with some wireless settings, since I've tried 2 different adapters and was getting the same result, unless both were faulty I suppose. I also don't think it's my router's issue, because the wireless is working great on other wireless devices. I am using windows 7 on the desktop.
View 5 Replies View RelatedI have a homeplug network as follows:
6x 85Mbps homeplugs in different rooms, each connected to a 5 port switch
2x rooms contain a PC
5x rooms contain a Squeezebox of various types
Router connected to homeplug
I have realised that I am only getting very slow network speeds of between 10-15Mbps (LAN SPeed Test)which affects Squeezebox's ability to play several devices synched up at a time playing 320Kbps MP3s
I have done some proprietory testing in my home by switching devices on & off & testing network speed accordingly but no significant gains seem to be made. One PC seems to report far lower speeds though at 5Mbps which is 3 times lower than the other PC. They are set up to read/write files from eachothers shared folders (but not simultaneously).1st question is, am I being realistic about the speed of data throughput I expect on a network of this type? I was expecting a much higher speed like 50Mbps.I wouldn't mind investing in the faster Homeplug system but having to buy 6x adapters isn't worth it if I will only get a marginal improvement.
I need to know what is wrong I am on a wireless 3G network with .8Mb speed test but I have very low download speeds. Tech Support Guy System Info Utility version 1.0.0.2 OS Version: Microsoft Windows XP Home Edition, Service Pack 3, 32 bit Processor: Intel(R) Core(TM)2 Duo CPU E6850 @ 3.00GHz, x86 Family 6 Model 15 Stepping 11 Processor Count: 2 RAM: 3325 Mb Graphics Card: ATI Radeon HD 2400 XT, 256 Mb Hard Drives: C: Total - 286134 MB, Free - 237445 MB; Motherboard: Dell Inc., 0GM819 Antivirus: avast! Antivirus, Updated: Yes, On-Demand Scanner: Enabled
View 4 Replies View Relatedin my house we currently have a ps3, 2 xbox's, a wii, 4 iphones, 2 pc's, a laptop, an apple tv, and 2 android tablets running off one internet connection. In my room, i have my PC, my xbox, and my apple tv. as you can imagine, my internet is painfully slow, although we have the fastest available from our provide (7mb per second i believe) running wired is fine but theres no way of me being able to do that. How could i go about setting up a second private network for my devices only? i would want to run my apple tv, pc, phone and xbox off of connection. without it being as painfully slow as my home network. i was thinking perhaps an airport extreme, and running it off of my router.
View 2 Replies View Related