D-Link DIR-615 :: Wireless Adapter Interference With Xbox 360?
Jul 19, 2012
I have recently bought a wireless N 150 usb Dlink adapter, i have installed the software and have conected it to my router using WPS (I do not know the passphrase). The adapter is working excellent but when I added the adapter, my old SSID (Dlink) got switched to Dlinkelb7. Dlinkelb7 has full bars when the old Dlink only comes up so often with one bar. Since the switch of Dlink to Dlinkelb7 my xbox 360 adapter has a very hard time connecting to Dlink and it will not connect to Dlinkelb7 because it needs a passphrase. My router is also Dlink Model DIR-615.
View 6 Replies
ADVERTISEMENT
Aug 3, 2011
No matter what I try, I cannot get the DIR-655 to connect to my Xbox 360 Wireless N Adapter with N, only connects with G. If I use N only mode, it won't connect at all, even if I manually input the settings. Setting the security to WPA2 Only and setting the Cipher Type to AES doesn't work.
Hardware Version : A3
Firmware Version : 1.35NA
802.11 Mode : Mixed 802.11n and 802.11g
Enable Auto Channel Scan : Checked
Transmission Rate : Best (automatic)
Channel Width : Auto 20/40
Visibility Status : Visible
Security Mode : WPA-Personal
WPA Mode : Auto (WPA or WPA2)
Cipher Type : TKOP and AES
View 14 Replies
View Related
Mar 5, 2012
So I use Shaw as my ISP, with the dlink DIR-655 as my router.Originally I was using the DPC3825, and started noticing some nasty signal fluctuations on my phone and wii (would go from 5 bars to 1 bar, causing netflix to drop out, games to disconnect, phone browsing to stop completely, etc) which is why I bought the DIR-655. I have been looking for sources of RF interference.I do not own a microwave, all the electrical work in this house is brand new, I have no neighbors (live in middle of a forest). I have tried positioning, every wifi channel, building an aluminum satellite dish to direct the signal where I want it to go. I've had it in every room in the house, I've unplugged the fridge and all other RF electronics (cordless phones, etc), and the issue remains.
So what the heck is going on here? Does my house hate wifi signals?I was thinking maybe dirty power, but my house has emergency power batteries that run 24/7. Any dropouts or flickers aren't even noticed by the system. url...This is a picture of the path between the router and my roku box/wii/phone.The router is 1 inch below the camera screen, and the roku box is in the far room. it's 30 feet.what can cause severe fluctuations at 30ft?
View 6 Replies
View Related
Jan 7, 2011
Seems like there those saying they have gotten there DIR-655 and XBOX 360 Wireless N Adpater to work in 802.11n mode. The adapter will only connect in 802.11g mode (and yes I have the correct adapter). I have set the settings to following
802.11 Mode: Mixed 802.11n and 802.11g
Wireless Channel 2.462 ghz - Ch 11
Transmission Rate Best
Channel Width 20/40
WPA-Personal
WPA2 Only
Cipher Type: AES
Does this router really work with XBOX 360 Wirelss N Adapater. If so, how has others got this to work.
View 3 Replies
View Related
Aug 30, 2011
My friend has had constant issues with his wireless network using his dated Linksys router. So he finally decided to upgrade to the Netgear N750. It's a dual band router that simultaneously broadcasts 2.4 and 5 GHz bands. He setup the 2.4 band for the laptops and mobile devices to access, and the 5 band just for gaming on his xbox 360 Slim. He immediately ran into a problem. The 360 slim's built-in wireless card only picks up 2.4 GHz frequencies. To remedy this, he purchased Microsoft's xbox 360 wireless-N adapter as it can pick up 5 GHz frequencies. However, there was no change after plugging the adapter into the 360 slim. His HP laptop can see the 5 GHz network just fine, so we know it's being broadcast. Could it be the xbox is out of range of the 5 GHz band? Is the adapter not functioning properly with the 360 slim?
View 2 Replies
View Related
Dec 6, 2011
I am only getting G connections with xbox 360 wireless n adapter. I should be connecting with N.Internet is BT Infinity. Original BT HomeHub3 does not have n problem and I can connect fine at n speed!If I set e2000 to N only the adapter can not connect at all.I currently have to bridge to my laptop using N wireless card to get good connection speed.
View 5 Replies
View Related
Nov 15, 2012
Ive been trying to work this out on XBL forum for a while. all my settings seem to be correct ( UPnP, NAT type: open, no port forwarding or triggering, IP settings on Xbox's are auto).
The two Xbox can play online separately, when either one of them attempts to join the others party it disconnects from Xbox live.
According to the microsoft website, Xbox live only supports the Hardware version 1A and Firmware: 1.00NA.
My router has B1 and 2.00NA. is there a way to downgrade?
View 4 Replies
View Related
May 30, 2013
WRT610v2 running latest firmware.xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars.Connects to 2.4 network just fineWon't pull an ip address and reports "Not connected" when I select the 5.0 network.I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network.So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not..If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
View 13 Replies
View Related
Aug 12, 2011
WRT610v2 running latest firmware.
xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.
Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars. Connects to 2.4 network just fine, Won't pull an ip address and reports "Not connected" when I select the 5.0 network.
I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network. So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not. If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
View 2 Replies
View Related
Mar 9, 2013
can u use any wireless network adapter for the xbox360?
View 1 Replies
View Related
Feb 17, 2012
I have a Cisco AP1142 Standalone AP at two of my locations. However both of these are being rendered useless every night and require a reeboot to correct the issue, because of the high level of noise and vibrations coming from the extremly loud bands that play there, Someone sugested an enclosure stuffed with insulation but Im afriad of overheating the AP.
View 2 Replies
View Related
Sep 11, 2012
We have a small ofice in the 3rd floor of a building and we are using 2 access points Aironet 1130 URL
Since some time now the space has become really crowded with access points. 1 AP is on channel 5 and is almost unusable. The 2nd one on channel 11 has some APs to fight with and with smaller signall strenght.
I have been researching and read a bit about changing some access point parameters (RTS/CTS/timers) on a multi access point environment. I want to do that while waiting for 5GHz AP's (and because not all clients support 5GHz).
View 9 Replies
View Related
Dec 16, 2012
I have tried all firmware and go into router settings and it shows it's sending a wireless signal to Xbox. I have it connected via Cat5 cable.
View 5 Replies
View Related
Feb 14, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP :
Region : Netherlands
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : TL-WDR4300_V1_121225
ISP : Ziggo
Set up the WDR4300 with a USB drive connected (Platinum MyDrive CP 500 GB USB 3.0).Enabled the Media server, shared the entire drive, stuck an test .avi on there.My laptop has no trouble playing it from the attached storage, my Xbox sees the folders and files, recognizes them as playable formats but then does nothing once I hit play to get the file going.If I copy the exact same file to the shared folders on my laptop, navigate from the Xbox to that location it streams within the second.Also tried the same thing with a 16 Gb USB thumbdrive, same result.
View 1 Replies
View Related
Feb 20, 2012
Just today i've started having problems with my Wireless Network. Other adapters in my area are causing me to get random disconnects every few minutes.I've tried changing the channel on my router several times, but to no avail. Is there anything else worth trying?
View 8 Replies
View Related
Apr 30, 2013
We're getting complaints about a specific 1131AG in the field only being intermittently accessible. WCS shows both the a and b/g interfaces randomly bouncing, sometimes the reason for the bounce is unknown other times it says it's because it lost connection to the controller. I can ssh into the WCS but the engineer who setup the AP's doesn't seem to have enabled remote access via telnet or ssh.
We are also seeing these events:
802.11a interface of AP * is down: Controller 172.17.0.10 Reason: Max retransmissions for the AP have reached.Interference threshold violation reported by '802.11b/g' interface of AP *, connected to Controller '172.17.0.10'.I know I can adjust the threshold percentage, but that would only seem to mask the issue.WCS gives this version info on the AP:
Versions
<DIV style="DISPLAY: block" id=versions mcestyle="display: block;">
Software Version
6.0.202.0
Boot Version
12.3.8.0
[code]....
View 14 Replies
View Related
May 21, 2011
I have Wireless-G 2.4ghz 54Mbps (Linksys WRT54G) working perfectly short range. But have no connection when I'm in room about 80 ft from router and have doors to rooms closed. Partitions in home are concrete block, not sheetrock. Should I get a new N router? Is there a repeater or booster that will do the job? Or connect existing router to new router in other room with ethernet cable going outside then over roof of house then inside to room?
View 14 Replies
View Related
Aug 6, 2011
Wasted several hours after changing to a D-link DIR 825 router attempting to connect to my XBOX 360 (S) without success.Tried to use the 5 GHz broadcasting with following settings (the 5 GHz SSID didn't show up in the XBOX wireless list but I'm one of those ignorant trial & error:
- locked on 802.11n and WPA2,
- disabled Multicast Streams in "Advanced/Advanced Network",
- disabled WI-FI protected setup in "Advanced/WI-FI Protected Setup" (maybe unnecessary)
- disabled SPI and TCP & UDP Endpoint Independent i "Advanced/Firewall Settings/Firewall Settings"
In the end it was resolved by the info in solution 5 on the xbox page: The XBOX:es with built in wireless can only use the 2.4 GHz connection, and to be able using 5 GHz broadcast I apparently have to get the "black adapter".
View 3 Replies
View Related
Apr 28, 2011
I installed my DIR 655 today and had no problems accessing the network with any of my computers, however, I am completely unable to connect my xbox to the network. The issue isn't with connecting the xbox to xbox live, its with even getting it to connect to the wan.
[code]...
No matter what I do the xbox says it can't connect to the router, and in the router's wireless connections it shows my xbox's MAC address with an IP of 0.0.0.0.I installed my DIR 655 today and had no problems accessing the network with any of my computers, however, I am completely unable to connect my xbox to the network.
View 3 Replies
View Related
Jan 8, 2011
I just upgraded yesterday to the DIR-655 (ver B1, F/W Ver 2.00NA), and suddenly my sons Xbox 360 complains that the NAT is set to moderate. I'm not really sure what this means, but I've never seen it before and it wasn't an issue with my old router. It pertains to the DIR-655? I did some quick google searches and I've seen lots of different 'solutions' to this issue, but none of them seem to agree with each other and I'd rather not spend and entire afternoon trying one after another given that this router kills my internet connection for a full 20 seconds every single time I make any change.
View 4 Replies
View Related
Jun 22, 2012
I own the DIR-655 version B1 (EU version) living in the UK.I play xbox, specifically in Halo Reach. My setup isn't straight forward as I have 2 xboxes in the house, one wired and one wireless and I need to keep the NAT ratings open on both. This limits me to certain settings, and doesn't allow QOS on the v2.00 firmware due to my need to have dynamic ip addresses.I have just flashed the router's firmware with new version (DIR655B1_FW205B06) as it appeared available for download in the router's firmware menu. The old version was FW2.00 as said.any other settings to enable or disable, for wired, or wireless, that will optimise for xbox gaming. Finally, I also have fw version DIR655B1_FW206B02, which was emailed to me by D-Link, if this is any better.
View 1 Replies
View Related
Jan 7, 2012
I've moved into a new apartment with a couple of people who already have wifi set up. They are adament about me not running a ethernet cable across the apartment to my room for my xbox 360. I have a DIR-601 from my last apartment, and I am wondering if there is a way to set up the router as an access point that allows me to connect to the existing wifi network and then wire my xbox 360 in.
View 4 Replies
View Related
Mar 26, 2011
Xbox is connected via ethernet to DLink. Router does not assign IP address to Xbox but does to all other wireless devices and wired computer. Xbox can connect to xbox live via direct connection to modem so cables and adapter are all good. Can't assign either static or dynamic IP address to Xbox. Have reset router to original config. Am at a loss of what else I can do?Have 2.01 firmware and have reset modem as well.PS....It has occasionally been connected in the past but currently no connection possible through router.
View 5 Replies
View Related
Feb 11, 2012
I've got an Open NAT but there's still some people i can't connect to (Xbox Live), i know theres a UPNP but it doesn't seem like it's doing anything.
View 1 Replies
View Related
Aug 8, 2011
How i can connect to my 5ghz wifi through my xbox ?
View 5 Replies
View Related
Oct 4, 2011
My netgear router kept dropping my internet connection so after some research I bought the DIR-655 router. It installed fine. My computer connects to the internet great and so does my xbox. But now my xbox doesn't see my PC so I can not set up a media center connection. I know it isn't a firewall setting or a setting on my computer because it worked fine with my old netgear router and the router I had before that. I even double checked by turning off the firewall. I have version 2.0 firmware and the settings are out of the box. I assume there is something I need to set up to get this to work but I have not been able to find any answers on the internet. I don't know a lot about networking as I've always used out of the box settings and had success with everything working the way I like.
View 6 Replies
View Related
Aug 20, 2011
I've been using the Dir-655 for 2 or 3 years with my old Xbox 360 and an external G wireless adapter. Everything was working perfectly until I got the dreaded Red Rings Of Death the other day. I replaced the Xbox with a new Slim version with built in N capable network adapter.
After more than 10 hours of trying a variety of "fixes" I found from MS and in this forum, I am still at square 1.
Hardware Version : A3
Firmware Version : 1.32NA (this is listed as Live compatible by Microsoft)
802.11 Mode : Tried N only, G only and mixed 802.11n and 802.11g
Enable Auto Channel Scan : Checked
Transmission Rate : Best (automatic)
Channel Width : Auto 20/40
Visibility Status : Visible
Security Mode : WPA-Personal Also tried WEP
WPA Mode : Auto (WPA or WPA2) Also tried WEP
Cipher Type : TKOP and AES
I tried assigning an IP manually from the Xbox. But, no matter what I do, the router will not accept it. It is especially frustrating that the Xbox is visible to the unit. It simply will not assign an IP to it under any circumstance.
If you read the sales hype promoting the Dir-655, you will see a lot of nonsense about it being great for gaming. Given that, you'd think a simple solution would have been found and posted for this issue by now. Surely, end users shouldn't be trying 100 different possible "fixes", none of which work, at this late stage of the firmware upgrades. If I sound a tad fed up, it's because I am. After the expense of the new Xbox, it appears I now have to junk my router too.
Here is the status screen taken when it was in mixed mode. Changing it to 'G Only' didn't make any difference:
View 12 Replies
View Related
Mar 9, 2011
Is this router good for gaming with the Xbox 360 & PS3.My linksys wrt120 n is giving me fits I need a better gaming router.
View 2 Replies
View Related
Dec 19, 2012
I just upgraded my dir-835 to the latest 1.03 firmware and it still not working.Plugged an ntfs firmated drive with films on it into the router and windows media player can see and stream from the router but xbox 360 is not detecting the media server !I tried with a dir 857 and xbox works fine but with the dir 853 no go
View 14 Replies
View Related
May 11, 2011
I've been trying to play Final Fantasy XI on my XBox 360 through this router. I have the latest firmware available. According to FF's tech support I need to port forward TCP and UDP 50000 through 65535. I've done this numerous times on my own and twice through D-Link support and am still getting disconnected.The game plays fine when it's connected directly to the modem, but as I'm not the only person in the house this isn't really an option.
View 3 Replies
View Related
Feb 12, 2012
I'm having trouble seeing my PC from my XBox (I want to use WMC to stream video to XBox). Here's my setup:
ISP provided modem (No branding), connected to my PC Network out (Wired) from modem to Dlink DIR-665 router (which is broadcasting WIFI) Network out (Wired) from Dlink router to XBox
I'm online with the XBox with no issue, but I can't access the PC through Media Centre with this setup. When I connect the XBox to the modem directly, I also have no issues. I'm using Norton Internet Security 2012 if that could be the issue.
View 15 Replies
View Related
Nov 23, 2011
I'd like to use my D-Link router as a network adapter to connect a PC to my existing wireless network. how to configure the D-Link router? I'd like to leave the Belkin settings alone as much as I can.
I have a D-Link DIR-615. Hardware Rev. is C1. Firmware Rev. is 3.10NA.
I also have a Belkin F5D8235-4 router. Hardware Rev. is v2000. Firmware Rev. is 2.01.04
View 2 Replies
View Related
Aug 12, 2011
i have a little network knowledge but the tp-link wa-500g is proving quite a challenge to set up.i am trying to set it up in client mode to use with the xbox 360.thhe problem is i seem to set everything up correctly but it doesnt actually seem to work or to connect to the main router..which is a sky sagemfast router...(could this maybe be the problem? and if so how could i sort this? i have set a static ip on the tp.link and set up in client mode and "supposedly" connected to the main router in which is hard to figure out if it has or hasnt...also my sky router has wpa security and i am wondering if something has to be configured in my tp-link wa-500g to connect? but i can find no information on this needing to be done.
View 3 Replies
View Related
