D-Link DIR-655 :: WNR200 No Port Forwarding Set Up For Vpn Just Virtual Servers
Jul 16, 2011
I have seemingly tried everything! I am still getting vpn error 720 using windows client trying to connect to vpn server using PPTP. I am about to go out an buy another WNR200 because vpn works flawlessly on that router. I have 2 virtual servers set up, one for port 1723, the other for port 47(GRE). All the ALG check boxes are checked(I have tried them both ways, when they are un checked and I use port forwarding i get vpn error 800). I have tried with SPI enabled and disabled. No port forwarding set up for vpn just the virtual servers. Firmware is 1.34NA, 2010/04/16.
View 11 Replies
ADVERTISEMENT
Jan 31, 2012
the difference between Virtual Servers and Port Forwarding on the DIR-825? I'm transitioning my router setup for a Tomato/MLPPP router to the DIR-825 and I'm a little confused on when you would use "Virtual Servers" and when you would use Port Forwarding? In the past, I've always relied on port forwarding to allow access to specific services on my LAN (ie. VPN, Apple Remote Desktop, etc.), so again, unsure what the Virtual Servers is used for?From what I can tell, Virtual Servers is for services that require a single port for communication (ie. a basic SSH setup on port 22) while Port Forwarding allows for the setup of services that require multiple ports (ie. VPN on ports 500 [UDP], 1701 [UDP], 1723 [TCP] and 4500 [UDP]). Is that the differences between the two configuration pages? It just seems odd to me to have two separate windows for just this difference? If that's the case, is there any reason I couldn't just use port forwarding, even for services that only require a single port (just to keep everything on the same configuration page, under Port Forwarding)?
View 2 Replies
View Related
Feb 24, 2013
Region : Mexico
Model : TD-W8968
Hardware Version : V1
Firmware Version : the last version of this web page, i forgot number
ISP : TELMEX (infinitum)
i have some problems to configure the port forwarding in my router, don't it work ! but the port number 80 it works with my sub-domain in the internet. after i change this port to 8080 still dont work the port forwarding. the FTP server its ok.
[code]......
View 3 Replies
View Related
Jan 11, 2012
One of the persons involved in a home network has installed a Dlink DIR-825 Rev-B Extreme router on the Comcast cable system to allow a 'better' wireless signal on upper floors of the home. Two others involved in the same home network use a 'secure desktop access' software called NetOp to access the network remotely. To facilitate this software, we must 'port forward' port 6502 on BOTH UDP and TCP to the single system that is accessed.
However, this setup (simple port forwarding) does not seem to work - neither does 'virtual server', for that matter. Prior to this router being installed, it was extremely simple to accomplish this remote access using a Linksys router, so our software firewall configuration has not changed but the new Dlink seems unable to allow remote access.
How (and via which of these access methods - port forwarding or virtual server) would be best? This configuration seems frustratingly difficult to accomplish and I'm about to take the Dlink 'out' of the network and re-install the Linksys with a 'high-gain' external antenna to facilitate simple signal enhancement.
View 3 Replies
View Related
Mar 5, 2013
I just bought this to replace a working Linksys but wanted gigabit so after reading a lot of reviews this is the one I picked up. So tell me what is the magic toggle to get port forwarding to work or virtual servers? I've configured them on Linksys, netgear, Cisco, etc 100 times with no problems. Nothing I configure on this confounded thing works. I've setup 6 port forwards, RDP, FTP, VNC and none of them work. Nothing. "Connection timed out" when trying to connect. This works on my other router just fine so its not my software, or my PC configuration as they have no changed. Ports are correct.
View 2 Replies
View Related
Mar 20, 2011
I wonder what the difference is between the virtual server and the port forwarding because the router I was using previously had only port forwarding. When should I use virtual server instead of port forwarding?
View 1 Replies
View Related
Nov 9, 2012
Region : Argentina
Model : TL-WR1043ND
Hardware Version : v1
I have read how to configure the Virtual Servers - Forwarding url...and added two entries, one for port 44612 and one for 32680 , my pc ip is 192.168.0. 100.Before I installed the router (my pc was connected directly to the lan connection) all was working just fine.And I double checked that the ports are not being blocked by firewall.
View 4 Replies
View Related
Mar 10, 2013
When can we have an upgrade to include 'Lookback' function for Virtual Server ? I understand both Build-120802 and Build-120926 does not support this Loopback feature. Without the loopback feature, we won't be able to test out Dynamic DNS URL is working or otherwise on local PC.
View 1 Replies
View Related
Jan 19, 2012
I have a small network in my garage, it's basically made up of a bunch of test servers. Those and a win xp machine are all hooked up to a switch, and the win xp machine also has a wireless usb stick that is connected to my wireless router, and is being used to share internet to the rest of the machines. The test servers along with the NIC card on my win xp machine sit on a different subnet, however.When I remote into the win xp machine from my house, i can run a second remote desktop in the first session, into any of my servers. I want to do work on them, but its very laggy.
Is there a way I can setup a port either on the win xp machine or my wireless router so that i can remote directly into one of the servers? so if the win xp machine has a wireless ip address of 192.16.13.102, and one of the servers on the 2nd subnet has an internal ip of 192.2.2.4, can i have it so i can make, for instance, 192.16.13.102:6333 forward to 192.2.2.4? If not, is there any other way i can directly remote into one of the servers, by passing the first remote desktop into win xp? What settings would have to be the same across the line?
View 1 Replies
View Related
Mar 7, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
View 1 Replies
View Related
Feb 16, 2011
I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
(yes, I've STFA, but don't know what else to do).
View 2 Replies
View Related
Mar 22, 2013
Region : Others
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0
ISP :
My router is TDW8961ND
The firmware version is 3.0.0
The hardware version is 3.0
I am trying to have a virtual http server at port 80 but when I do this and save, I get this message: "Notice: The WAN HTTP port of CPE will be chaged to 8080 if submit successfully."Then after that I cannot access the server at port 80.
View 2 Replies
View Related
Apr 7, 2013
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies
View Related
Feb 21, 2013
Region : Hongkong
Model : TL-WDR3600
Hardware Version : V1
Firmware Version :
ISP :
When using the USB printer port share function, I found that some PCs, which had never physically connect to a USB printer before, will not have the virtual USB printer port in the port selection. In this way, TP-Link's USB printer controller will not be able to setup the connection. The PC will not be able to use the shared printer from my WDR3600.how can I create a virtual USB printer port in the remote PCs (without need to physically connect a printer to them) or other method to use the shared printer?
View 5 Replies
View Related
Feb 9, 2011
How I do it? I know nothing about this stuff... I can't open the ports.
View 1 Replies
View Related
Dec 27, 2011
I was trying to port forward and could not get it to work. I run a Camfrog room sever of my desktop computer. I needed the TCP port 6005 open to the desktop and UDP ports 5000-15000. I enter that in to the Port forwarding setting but it never work. So later on today I try this I blank out the TCP 6005 in the port forwarding and letf the UDP setting in it and saved it. Then I went to the Virtual server settings and add camfrog3 in the name and put the TCP port 6005 in to it and check it and save the setting and bingo it work.
View 1 Replies
View Related
Feb 8, 2012
Alright, so I'm trying to set up a Minecraft server without having to use some sort of hosting program, such as LogMeIn Hamachi. I have tried port forwarding both my external IP from "whatismyip.com" and from ipconfig in the CMD WITH the correct Minecraft port, and others still cannot connect. note that I can only connect to my own server when I use the IPv4 address from my CMD. get my server working so that others can connect? (I have been sure to change my "server properties" file's "server-ip" line accordingly.)
View 1 Replies
View Related
Feb 11, 2011
I setup port forwarding for many router before, but I couldn't get this one to work.I triple check all of my configuration, they all setup correctly. But the port/ports on the router is not open.
View 1 Replies
View Related
Jan 18, 2012
I have read the sticky about the Game fuel, and i have tried resetting everything, static IP address, all the info i have found on line. i still i keep getting booted when i join a game, or most of the time i cannot join a party. No matter what changes I make it gets worse than factory setting. i have read for hours on different ways to set up the router and what not. i have changed settings on the PS3, router and still getting nowhere.so can some one pls tell me how to set this thing up before i use it as anger management.?i know how to access the router page . but i don't get the setting up port forwarding.
View 10 Replies
View Related
Mar 13, 2011
I want to setup a virtual LAN setting in a single machine, whats the procedure?
View 1 Replies
View Related
May 20, 2011
So I have two xbox 360's plugged directly into my dir-655 router with Ethernet cables. I have no idea how to port forward these, correctly and everything I try ends up with my router being reset. I don't have a pc connected to the router, only a wireless laptop.
opening ports for multiple xbox 360's (Black Ops is what we are trying to play).
One thing I do know is that when I tried portforward.com's walk-thru for port forwarding, when I enter the ports into the dir-655 port-forward menu, I can no longer connect to Black Ops at all, it says servers are down (WHICH THEY ARE NOT I CHECKED).
View 13 Replies
View Related
Feb 4, 2011
I am using DIR-655 A4 router and I have a server that needs DMZ and a PC that needs a port.So, I have set the dmz to 192.168.0.100 (SERVER) and set the port 2000(or any) to forward to 192.168.0.2 (PC).What I found out was, the port forwarding works well for several hours and suddenly it fails and won't forward until I reboot my 655 router. I am really tired doing this every day. I tried firmware 1.21 to 1.35 and non of them were good.I know that 655 has good performance compare to its price but I think it has world's worst firmware.
View 9 Replies
View Related
May 12, 2011
Edit I've found a work-around. It's on page 2: [URL]
I'm having this really weird issue with my DIR-655 revB. I have some port forwarding rules set up and externally they work fine. However, if I try connecting to my IP address using those same ports from a computer within my LAN, it won't connect.
Externally, I can ping my WAN address and connect through forwarded ports. No problems. Internally, pinging my WAN address apparently works (just now is the first time that's worked for me), however I can't access any of my computers using the WAN IP and port forwarded ports. I can access them by going directly to their hostnames or LAN IPs.
Things I've tried:
-Disabling/enabling firewalls on all computers involved
-Disabling/enabling QoS engine
-Disabling/enabling DNS relay
-Disabling/enabling Advanced DNS
-Adding custom nameservers from Google and Comodo
-Restarting computers
-Clearing DNS cache (I use a dynamic DNS name which works externally but not internally. This gets the correct IP internally and connecting directly to the IP doesn't work either.)
-Modifying the NAT Endpoint Filtering settings
I have an external DSL modem connected to the router using PPPoE if it matters.
The weird part is that it works externally but I've modified all of the values I can think of in the config with no luck. I upgraded to the DIR-655 from a DIR-615 which had all these settings in it and worked fine (until it started acting up which is why I replaced it).
View 14 Replies
View Related
Dec 6, 2012
I recently upgraded my internet service and received a D-Link DIR-815 from the company as they couldn't get our older router working with the new service (4G)
My brother plays Star craft and you have to forward ports to be able to host games for others to join, but it doesn't work.
I know how to port forward because our old router had exactly the same setup, but I have one issue though, when I look at the DIR-815's manual, and even in posts made by D-Link, I've seen them asking if the filters for the firewall are set to Endpoint Independent for UDP/TCP, now I know where this is, it's under Advanced/Firewall Settings, it even shows it there in the manual, but it's not there at all under my firewall settings, my older DIR router had it and we had no problems port forwarding, I'm not sure if it was removed in a later hardware or something?
View 13 Replies
View Related
May 25, 2011
I have a server that is running on 2003 and we are having a few problems and in the event log I am getting id101 with the message whats virtual is not enable and i am not sure what this refers to or how to sort it out.
View 2 Replies
View Related
Jan 19, 2013
Router Model: TP-Link TD-W8970 port forwarding my modem/router. I previously was able to successfully port forward a Valve Source Server and had other people join on the internet so...(It worked) I recently reformatted and since have had issues.
I'm currently setup with PPPOA and I've added various ports for different programs (a Teamspeak 3 Server[9987] and Minecraft[25565]) either dont work. I used a port checker program and they either say the port is closed or the connection is refused...I've tried using a static IP but I think i configured it wrong becuase i was barely able to get the internet while using it, either way..the ports didn't open.
DCHP is disabled (Tried enabling, didn't work) The above ports are enabled with Windows firewall (inbound+outbound) and Im not using any Anti-virus software to block the ports. Windows 7 64bit, fresh format and ports that wont go through.
View 4 Replies
View Related
Nov 30, 2012
None of the port forwarding settings are working at all on my router. I have just a couple very simple settings. One of them is just an IP camera. I input the name, the TCP port, the computer (IP address) and that's it. This works just fine with my other Netgear router, but with this router, NADA. The router has the latest version of the firmware applied. Just applied it. Hardware version B. Firmware version: 2.10NA. If so, then I really need my money back since it is a main function of a router and it should work. Can't return it now, since I bought it several months ago. Never knew port forwarding didn't work because I never needed it until now.
View 6 Replies
View Related
Mar 3, 2011
I was changing the port forwarding configuration when suddenly the router stopped working, and now the "D-Link" light is constantly on, and the power light and the 4 LAN lights are flashing. Nothing worked, resetting, or unplug and plug again in a short time.
I disconnected it for 12 hours, and when I plugged in again, it kinda worked, and the settings where factory defaults, so when I tried to connect it to DSL via PPoE, when ( I believe ) it reboots to accept the changes, it starting flashing again and completely stopped working.
So I waited 12 hours more unplugged, plugged it and it worked, and the setting from 12 hours earlier were still there. But when trying to connect to the DSL it stopped working AGAIN.
Now I don't know what to do. I guess I am going to keep trying connecting with little differences, until something.
I believe it still has warranty but since the is no official service in Uruguay, it isn't economically viable to send it overseas.
I am currently connected directly to the DSL, sharing connection to other computers through a switch and hosting an ad-hoc wireless network, but the performance is terrible and the wireless range is minimal.
View 1 Replies
View Related
Jan 8, 2010
I have DIR-615, connected via ethernet. I enabled port forwarding for Quake 3, using the range of 27660-27980 to account for custom server ports. Set schedule to "always" although also did "never" but it didn't make a difference. I checked the FAQs for frequent resets vis a vis application outbound requests, which recommended disable uPnP and this had no effect. Symptom: when Quake 3 attempts to connect to the Master Server, the router resets all connections, LAN and WLAN. It takes approximately 30 seconds to regain connection to WAN, although LAN does not drop. Also during this time, the world sigil on the router itself turns orange. This is the only time this happens, when trying to play Quake 3. Previous router to this one was Linksys (by Cisco) BEFSR41, in which simply setting up port forwarding for the client IP address allowed connection. I can find no particular reason why the router resets all interfaces when blocking a port, if it is indeed the firewall triggering this.
Other infos:
Model: Wireless N 615, DHCP enabled on both sides
LAN connect: Category5 to 10/100 NIC onboard to Intel 865GBF
Client firewall: none
Client OS: Windows XP Professional SP3
View 6 Replies
View Related
Mar 18, 2013
Region : UnitedKingdom
Model : TD-W8980
Hardware Version : V1
Firmware Version : 0.6.0 0.6 v000e.0 Build 130304 Rel.38108n
ISP : Plusnet
Have spent most of the day trying to get port forwarding to work! U an trying to run a mail server and am forwarding ports 25, 110, 995 to a PC on my LAN, only problem is the ports never get there. I can connect quite happily if I wire a laptop to the router BUT as soon as I try to connect from externally either by mail.domainname or IP I am not able to connect. Using telnet I can't connect to the ports either. If I forward port 80 I still connect straight to the router rather than trying to connect to the mail server for webmail. At the moment I am having to forward all mail from the server to a google account just to read it!!
View 14 Replies
View Related
Oct 23, 2011
I'm trying to configure port forwarding for FTP but in my case it isn't as simple as i assumed ... i have an actiontec router/modem that serves as incoming internet from my provider (FIOS), which i connected to my own router (dir-825). i mainly configure my network on the dlink and leave the actiontec alone.
[CODE]...
View 13 Replies
View Related
Jul 29, 2011
I currently use a D-Link DIR-655 router on a game server I run and I've been having this problem for sometime now. I have the router hooked up to the internet modem, and then my server computer hooked up to the router's first port. I use port forwarding to forward the game ports, as well as my FTP server ports. I have about 80 clients or so logged in at a time on my server.The issue is the following. Our internet connection has an external IP of 67.23.155.123 (this is just an example). My internal IP is 192.168.0.101.When I do "netstat" to see all the clients logged in to the game server on this computer or when I run Wireshark, every client logged in to the server (for this game application) is shown as having an IP of 67.23.155.123 (the server's external IP).On the other hand, for our FileZilla FTP server, if I run Wireshark/netstat, I can actually see the client's external IP (i.e. each individual IP of people logged into the FTP).If I hook up the server directly to the internet modem, this isn't a problem, and I am able to correctly see the IP of each client logged in to the game server individually.
View 12 Replies
View Related
Jul 27, 2012
First off, my router is a D-Link DIR-655, firmware v2.07. I'm trying to port forward port 25565.
My port forward settings are this:
However, when I use this open port checker, it claims that I don't have that port open. It looks like this, without the blurred out parts:
Added note: The way I want to use it is by my IP (xxx.xxx.xxx.154:25565). I have the software installed to do so (I'm using a minecraft server, connecting through minecraft), but I can't enter my IP in the IP address field, it says that it's out of the range of the LAN.
View 2 Replies
View Related
