After I change my router, I recently found out that I cannot access remote network resources after VPN tunnel is established. I use CISCO System VPN client. I can see the connection is successful. I cannot ping server on the remote network
View 2 RepliesI have setup a VPN connection on a 891 router. I can connect to the VP both but am unable to ping or access any resources on the remote network.
Here is my running configuration:
[code]...
I have 3 networks coming from the DMZ (VPN) and only one works:10.132.24.0/24 Not working10.132.25.0/24 Not working10.132.26.0/24 Working The thing is, the one that works is on the same network as the DMZ(VPN) interface. The other two do authenticate and they get an IP from the VPN Pool. but they just cant access anything.
View 11 Replies View RelatedI am having an issue with my Cisco VPN Client. I am new to VPN setup, so this is probably something easy I am missing. I have a 2611XM router acting as my internet gateway for my local lan, and my VPN Server. I am doing all my testing from a company laptop with a mobile broadband card. The VPN will connect, but anytime I ping anything within the inside network, it comes back with the public IP of the outside interface. I have NAT overload configured so everything on the inside network can access the internet, which it looks like might be causing my problem.
When i remove the nat overload on my fa0/1 interface, the vpn will connect to any resource on the inside.
I want a simple remote client-initiated VPN for employees to access corporate resources from home simultaneously with being able to access the internet. I am using CCP and seem to have several options including Easy VPN server, SSL VPN. I also can choose "Full Tunnel" or not.I have a 2911 router. I have a static range of internet IP addresses. The router is already functioning with inside to outside and outside to inside NAT, etc.
View 1 Replies View RelatedThe Linksys is connected to a cable modem and a Dell Vostro system, the Netgear is connected via Cat 5 to the Linksys and the Linksys is the DHCP provider to the Netgear.The Vostro shares hard drives, folders and printers to the networkBoth have wireless and wired users.They are each DHCP providers to their users.How must I configure each to provide users on both routers access to all network resources
View 2 Replies View RelatedI have two places that I work out of. One is in Romania and one in Bulgaria. In Romania, I have a small office/home network set up. It has at least 8 computers (including the three that I have with me currently - some wireless and some towers) and a couple of android phones and Ipods. I have no trouble accessing any of the computers shared folders or them accessing mine. There are a varity of operating systems used there from XP, Windows 7 and Mac.Everything works great. All the computers can access each other shared resources. All the computers are set to get IP automatically from my DLink DIR - 600 router. I have brought my three computers to Bulgaria (tower and two laptops). They are all set the same- no changes in settings. However, in Bulgaria, All three computers CAN access the internet but NOT each other.
[code]...
So here is my issue. I have two sites, each with a Linksys RV042 on thier site.
Site 1:
External: 142.142.142.142
Internal: 192.168.25.0/24
Site 2:
External: 143.143.143.143
Internal: 192.168.26.0/24
We have setup a site-to-site VPN between these sites, and all traffic is running back and forth without isse.
At Site 1 we have configured the Client VPN for use with the QuickVPN software. Again, for site 1, this is not an issue. We are able to access all internal resources at Site 1 without issue (expect for some DNS related problems).
The problem that we have is attempting to access Site 2 resources via the QuickVPN connection at Site 1. Even though they are not suppose to exist, we are able to ping 192.168.26.1-6 (which are ghost addresses likely created by the RV042's) but no actual systems on at Site 2.
I have added the Client VPN connection at Site 2, but it has the same problem accessing resources at Site 1.
I'm working on setting up a couple of new WAN sites with 256K frame relay circuits back to our main building. Each new site has a new PVC, and both are pointing back to a PVC on a T1 at the main building. The main site has a 2801 with a single CSU/DSU WIC, and each new site has a 1841 with a 3560 connected to fa0/1. At both sites, I'm able to get the circuit up, and the serial interfaces at both new sites show up/up, and the subinterfaces at the main site also show up/up for both sites. Routing is being done by EIGRP, and both sites are able to establish the 2801 as an EIGRP neighbor, and I'm able to ping/tracert anywhere on our network by name or IP, so routing and DNS appear to be working. I can also ping both new routers from the main site. However, that's about all I can do. I'm not able to access any resources on our network (email/shares/internet/intranet/etc) from the two new sites. I can ping the new routers/switches from the main site, but can't ssh to them. I can ssh to them locally. There are no firewalls in the equation, and I don't think there are any ACL's in the picture either.
Can ping and tracert just fine anywhere on our network (from both the 1841, a PC plugged into the 3560, or a PC plugged directly into the fa0/1 port on the 1841), including out to the internet, by name or ip.Can ssh to local router, but not to anything that isn't localDNS is workingDHCP not working using ip helper pointing to DHCP scope on server at main site, have to use static IPCan't rdp to anythingCan't get emailCan't browse windows sharesCan't get to any websites, external or intranet. IE says "Website found, waiting for reply..." but eventually times out.
I did some testing for communication over certain port numbers using telnet and nmap, and found the following:
Can telnet to url.. and local intranet webserver on port 80 (http)Can telnet to two of our Exchange Servers on port 25 (SMTP)If I run an nmap scan on url...com, or our intranet webserver, it confirms that 80 and 443 are open, but the pages will not load. I am able to telnet (port 23) to a state mainframe via the internet that some of our employees use, and I do get the expected login screen. I tried erasing the config one of the new routers, and just added back the bare minimum config to get the circuits up (serial/ethernet interface configs, eigrp), but saw the same symptoms.
One other thing to note: the 2801 at the main site has three other frame relay sites connected to it on the same WIC as the new sites, all of which are working fine.
I just don't understand why I can ping everywhere I need to be able to ping, and port scans show that communication is open over needed ports, but the applications don't work.
I have easy vpn on my PIX 515e and working normally everywhere, except when my users go FRANCE, the vpn client connect, but, can't ping or access any inside network resources. when same user try any where here in EGYPT, it works normally.
View 2 Replies View RelatedI have a CISCO Linksys WRT610N router on my home network which consists of the following 4 computers; Windows Small Business Server 2003, one Windows 7 Ultimate and two Windows XP Professional. How to configure a VPN on the WRT610N router that would allow me to access all of the computers on my home network over the Internet using the "Remote Desktop Connection" component.
View 2 Replies View RelatedI have a Cisco 881 setup with the following VPN config.
[code]...
The client is able to connect just fine to the network via VPN, but I am unable to gain access to any of the local resources. I know 192.168.1.1 has SSH running and 192.168.1.50 has telnet running but if I try to connect to either using the correct program they just timeout. I am really at a loss on why the vpn connection connects but I can not gain access to any of the resources on the VPN network.
I have a VPN server set up behind a home router in my apartment. I'm able to connect to it from other locations, and have verified that internet traffic is going thru the connection (ipchicken.com reports the IP address of the VPN network). But I can't seem to connect to other machines on the router subnet. For example, 192.168.1.1 connects me to the local gateway rather than my apartment router. Also, I can't connect to known good static IPs for other machines on the remote subnet, including the machine I'm VPN'd thru!
Note that in connection properties, the setting to 'use remote default gateway' is checked.
I have a (central) ASA5510 acting as a EasyVPN server and a number of (remote) ASA5505 as EasyVPN client. All the communication works fine between the different networks. The issu is the ASA itself. The remote ASA can ping the central ASA on it's internal IP-adress, but it can't ping any other resoruces at the central network. If I ping the DC at the central network from the remote ASA I get a deny in the central ASA with source address as the public IP-adress of the remote ASA and destination of the internal address of the DC. If I from the remote ASA do "ping inside ip-of-central-dc" it work's like a charm, but "ping ip-of-central-dc" dosen't work.
View 3 Replies View Relatedinternet connection could not be established. the port used was closed.
View 1 Replies View RelatedI have the netgear wndr4500 setup on my home theater shelves which are located in the corner of the room. When using my ASus G74sx with the Atheros 9002 wifi I consistently get disconnected. The wifi connection is lost and needs to be re-established.
Interestingly, when I am using the laptop downstairs the disconnects never happen. I have pored over my router's settings, updated to the latest firmware, as well as installed the latest drivers on the laptop. I also tried setting the router to short preamble and changing the channels to 11and automatic.
I use win7 os and samsung e2652 champ duos mobile. When I connect mobile to pc, the dial-up connection not established and show the error 777: the modem on the remote computer is out of order.
View 1 Replies View RelatedPPPoE connection isn't established...Config Cisco 1811 (c181x-advipservicesk9-mz.124-15.T15.bin):
...
vpdn enable
...
vpdn-group 1
request-dialin
protocol pppoe
[code].....
We try to establish a Site-To-Site- IP Sec- connection between a Cisco 876 (local site) and a Check Point-firewall (remote site). The Cisco 876 is not directly connected to the internet, but is behind a DSL- Router with port-forwarding, forwarding ports 500 and 4500. The running config of the Cisco 876 is appended to this discussion thread. Unfortunately I get no output when debugging the connection with commands "debug crypto isakmp" and "debug crypto ipsec".
From the Checkpoint-firewall point of view the connection seems to establish, but there is no ping answer.
The server on the local site that should be reached from the network behind the Checkpoint-firewall has a routing entry "route -P add [inside ip-net remote] 255.255.255.0 [inside ip local]" (see also appended running config for naming of ip- addresses). Establishing a Cisco VPN- Client connection to the same Cisco 876 router works fine.
All my years on the computer and internet, i've only been connected via ethernet directly from my cable modem as i have just 1 desktop. Anyhow, i just bought a laptop yesterday and so, a router is a must to connect wirelessly. I received an old Linksys BEFW11S4 v4 router from a friend and decided to use it as it's still functional. Yes, i know it's an ancient router but i'm on a tight budget.The setup - I have the ethernet from my modem plugged into the router. I have another ethernet cable in slot #1 (router) connected to my desktop. For my laptop, it'll be a wireless connection.Issue - Now, the connection for my desktop (via ethernet cable in slot #1 on the router) works perfectly fine. I have it set up (on browser - 192.168.1.1), added the SSID, WPA Shared Key and such. The only issue is with my laptop. Everytime i switch on my laptop, i cannot establish a connection (after selecting the SSID and entering the key). The ONLY way for me to get a connection is if i power off then on the router. Each time i turn on/restart my laptop, i'll have to power off/on the router in order for me to get it to work.
View 9 Replies View RelatedWe have a D-Link DI-524 wireless router that has had no problems until today. Our laptops (with Windows XP), iPods, and iPhones all show that there is an excellent wireless network connection (as usual), but none of the computers or devices will connect to the Internet. I tried resetting, rebooting, and unplugging the modem and router. The router and modem seem to be fine. When we disconnect the router and plug the laptop directly into modem, we have Internet connection (i.e., it's not the IP).
View 4 Replies View Relatedi have 2 RV048 and one RV016
I have established VPN gateway to gateway tunnels; all routers use functional DYNDNS
IPrange site 1 192.168.123.1-254 external adres x.y.z.w
IPrange site 2 192.168.124.1-254 external adres a.b.c.d
IPrange site 3 192.168.122.1-254 external adres e.f.g.h.i
site 1 with 192.168.123.x has two win 2008R2DC servers, running AD, DNS, DHCP, RRAS with address 192.168.123.4-5
i can ping the routers only if i add the route to it but cannot ping further (route add command)
if i dont establish the route then nothing pings
How can i use the tunnel to connect to the servers in site 1
I've set up a VPN using a fortigate 50b wifi and forticlient ipsec VPN. when I log into my office from home, I cant see anything on my network at all. I can however remote desktop into other PC's and can access stuff that way. I was under the assumption that ... one a VPN connection is made in the LAN you should be able to see other pcs and servers in the workgroup. Is this not the case or do i need to configure something?
View 2 Replies View RelatedI have a Cisco 881 and I want to use Easy VPN.
-VLAN 1: 192.168.4.0
-WAN: 10.0.0.0
-VPN: 192.168.8.0
VPN connects and I get an IP of 192.168.8.100 from my pool. I can ping my cisco at VLAN1 (192.168.4.1), but I cannot access my local resources. I guess I miss a NAT configuration.
I get this message in response to clicking on "Diagnose Connection Problems" which was returned to me in I.E. 9 after visiting yahoo.com, other sites and most interestingly, even after trying to get to my DIR-825 at IP address 192.68.0.1. The only common element here is the DIR-825 so I suspect there may be some kind of misconfiguration in the device. The only way that I have been able to clear this condition is to reboot or repower my DIR-825.
View 7 Replies View RelatedI have an intermittent issue happening on my company's firewall, and I'm at a loss as to how to troubleshoot further.
We recently made some changes to our network, which included moving an ASA 5505 from one location to another. In moving this we also connected it to a different switch. It used to hang off a Cisco 3560, and now it hangs off a ProCurve 5406zl.
The setup is that the ASA is connected on two ports to the HP, which is simply a layer 2 device sitting between the firewall and the uplink to our ISP. One port, e0/0, is the outside interface and is set to switchport access vlan 2. The second interface, e0/1, is set for vlan 1, also access mode. It has an IP of 10.0.0.2. The HP on the other end of that has an IP of 10.0.0.1. So outside VPN connections come through the HP to the ASA on e0/0, and back out the ASA on port e0/1 to reach devices on the internal network.
What happens is that when a user connects to the VPN, they can reach internal resources intermittently. For example, I tried to ping an internal server IP address (let's say 10.0.0.23) from my laptop, while on the VPN, and pings failed. However I could ping that IP from the ASA itself. Another example is that during one VPN connection I was unable to connect to an internal web server, but once I disconnected and connected ahain I could reach the server fine.
The intermittent nature of the problem made me think that it could be an ARP issue, that somehow the traffic is getting sent back out the wrong interface sometimes, hence the lack of communication. However when I did show switch mac-address | include mac address, using the base mac of the HP, I only saw the mac address of the HP on one interface, e0/1. That makes me think that things are working as they should. Although I guess maybe it should appear on both interfaces...? I don't know. How I can most effectively troubleshoot this? It seems like the symptoms are indicative of some kind of rookie mistake, but for the life of me I can't figure out what it is.
I have created remote access vpn in my ASA 5505. The tunnel is established but i am not able to access the internal network.
View 3 Replies View RelatedI have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies View RelatedI am connected with qvpn, I can log in to the router bios remotely, but when I try to map the network drive from my remote location it does not work.I can detect the machine on the network, but it will not go further and tells me that "said IP was found but could not locate G". Does this mean it is behind a firewall on server side and that I need to create a rule to allow the incoming traffic? Or could it be something else.
View 1 Replies View RelatedI have set up an access point as per the instructions I found on this site. It works perfectly, holds a wireless signal fine. Now, I have the challenge of trying to remote connect to the home computer that is connected to this access point. I have absolutely no clue as to what changes in settings have to be made.
View 4 Replies View RelatedI recently purchased a 825 and a WD Mybook Live. I have been going back and forth on the WD board trying to resolve a remote access issue with the mybook and I am being told to do some settings in the router and I am not sure I have dine them correctly> It has not resolved the issue but I would like to make sure I am correct before I claim its not a good fix. The mybook is connected into a network port on the router which is connected to a High Speed modem and then out to the internet. Initially I was told to enable UPnP on the 825, which was already enabled. Then this is what I was told to do by a WD tech. You could try assigning a static IP to the My Book Live, then making sure ports 80 and 443 are assigned to that IP on your router. It is possible that something else is taking one of these ports. We use uPnP to try to open up these ports, and if it fails, we resort to relay mode. In the future, we will allow you to set these ports within the My Book Live to other than 80 and 443.
View 7 Replies View RelatedI am having trouble accessing my DIR-655 remote management screen via ip to my network.To make sure i didnt have any odd settings, i did a hard reset on my router first.I then enabled remote management, and left the default port 8080 I try to access viw the ip address on my status page suffixed by the port 8080 [URL] page cannot be found.I then enabled https and tried to access via:[URL]page cannot be found.I then setup a entry in the virtual server to redirect http requests to my workstation hosting IIS7, if i connect to localhost, the iis welcome screen appears, but if i browse to my ip, i get nothing.I am using Cox residential service, i called them and they informed me that they do not filter or block requests in any way.
View 12 Replies View Relatedi have a WD My Book Live and it's connected to my DIR-825. i'd like to configure the router to allow FTP access to the NAS from the internet. the drive has an option to enable FTP in it's configuration, but i have not done this before and i don't know what to do to create a solid/secure FTP portal so that i can access my files remotely.how do i configure the router for this ? my router is set to DHCP and i have turned MAC filtering on.. in particular i am looking for the ability to transfer/copy files from the drive, and not allow any modification/writing to the drive from the outside.
View 10 Replies View Related