Dell :: 600m / Adapters And Bindings Connection Order?
Nov 9, 2003
I have Centrino notebook, a Dell 600m. Most of the time I use WiFi with this notebook to communicate with the Internet and my desktop. However, when I want to backup my notebook to the desktop hard drive I prefer to use the 100 MBps speed instead of the 11 MBps speed of WiFi. I have setup the connections order in the Adapters and Bindings tab in the advanced menu item in the Network Connections such that the Local Area Connection (100 MBps) it above the Wireless Network Connection (11 MBps). Well, when I enable the Local Area Connection and plug it into my hub, a second little notification icon shows up in the indicating that the 100 MBps connection is active. When I perform the backup, both the wireless and wired connections show activity. Upon further investigation, I have found that data leaving my notebook is going via the wired connection data going to my notebook is using the WiFi network. Why is this and how can I have it use the wired connection for both upload and download?
By the way, I am using the built-in Windows XP networking software and am not using the Intel software.
View 7 Replies
ADVERTISEMENT
Nov 1, 2012
I made the unpleasant discovery recently that all my corporate laptops are using the wifi network even when sitting on their docks or otherwise connected to the wired network. Most of them have intel wifi cards, and the proset software allowed me to disable-by-policy wifi if a lan connection is detected.Some, however, have a more generic wifi card that doesn't have fancy management software, leaving me with the default windows stuff.In an attempt to correct the problem I
a) Put Local Area Connections at the top of the Adapters and Bindings list
b) manually assigned cost metrics to the connections in the tcp/ip settings
View 4 Replies
View Related
Aug 11, 2012
My Inspiron 600M laptop running XP - SP3 connects fine to my wireless network when using WEP but refuses to connect when using WPA2. I have Verizon FiOS with an Actiontec router (MI424WR - Rev. I). Googling this issue produces lots of older posts about the need for SP3 vs. SP2, but not much else. Should I look into updating the laptop's driver? If so, how? I tried creating a custom password (key) with fewer digits.
I'm also not thrilled about the wireless speed I'm getting on this laptop -- about 6 Mbps even when it's right next to the router. (The desktop, with a wired connection to the router, gets 25.) (1) Could the two issues be related? One tech rep assured me that WPA2 would greatly increase my network's range and speed, but other people deny this. (2) Is this just due to the Inspiron's older wireless receiver, or is there something else I could tweak to improve my speed?
View 3 Replies
View Related
May 3, 2011
So I am using a dell inspiron 600m. I have problems with the wireless Internet (well any Internet for that matter). It tell me that there is no supported wireless adapter. The weird thing about it is that if I reinstall windows (windows xp, sp3) and the drivers then it works. But the next day it has the same problem.Tried uninstalling and reinstalling drivers.Switching off all antivirus and firewall settings
View 2 Replies
View Related
Sep 6, 2011
When I try and connect to the Internet, it doesn't connect. Windows Network Diagnostics give me this message:"There might be a problem with one or more network adapters on this computer- The network adapter "Realtek RTL8102E/8103E Family PCI-E FE NIC" is experiencing driver or hardware related issues- Make sure your Internet Protocol Bindings are correct. Also, I took a look at my Device Manager and there seems to be a problem with almost every one of them.
View 1 Replies
View Related
Sep 30, 2012
I just bought an alienware M14x and about 3 weeks after i set it up the LAN and WAN adapters stopped working and i couldn't get a wireless connection or hardwired connection.
I called technical support and they informed me it was due to a generic windows update that wasn't really compatible with my alienware machine. So i did a system restore and now its working fine and i disabled automatic updates.
Its been about a month since then and now I have all these updates that need to be downloaded and I'm not sure which one will cause my network adapters fail again.
View 2 Replies
View Related
Feb 22, 2013
I recently formated my dell xps l502 system and installed with windows 7 Os.after that my Lan and Wifi are not working.when i did the ip config /all.it is showing only the following options.
-HPrimary DNS suffix :
-NodeTYpe: Hybrid
-IP Routing enabled :no
-WInsx Proxy Enabled : no
View 5 Replies
View Related
Jul 1, 2011
I have a compaw CQ61 that is using the operating system windows 7 64x.
The problem occurred today when logging onto windows. Windows tells me that the connection i have to the router is limited. Other devices i have in the house are capable of connecting to the wifi router. When deleting the connection and trying to reconnect to the router, it brings up the message that it is taking longer than expected to establish a connection and then eventually brings up the message "limited connetion"
When trying to connect the laptop to the router via cable, it doesn't even recognise that it is connected and does not establish a connection.
When using the windows connection troubleshoot, it detects a driver problem with both the wifi adapter and the Lan adapater. Therefore i uninstalled and reinstalled both devices but still suffered the same problem.
When clicking the connection i am attempting to connect to, right click status, details.. everything is in blank, it gives no information regarding to the connection.
View 14 Replies
View Related
Aug 11, 2012
I have setup Powerline Adaptors connected to a BT ADSL Broadband Modem and to a Humax Freesat box, but I keep getting a message telling me that there is no internet connection.
View 4 Replies
View Related
Jan 20, 2013
My emails are randomly arranged, how do I put them in the order that they are 'sent' or 'received'?
View 2 Replies
View Related
Sep 5, 2012
I have a Linksys WUSB100 ver.2 which i'm using on my desktop (uptodate Windows 7) for over a year now. I never had any problems with it until about a week ago.
After starting the computer, it had no network-connection, nor could it find any network anymore . The led-light keeps flashing blue and the device gets pretty hot.
I've tried about everything, i think:
- I've tried to update the drivers, but the installed driver were already uptodate.
- I have re-installed the device with no effect.
- i've installed the device on 2 other computers; my Windows 7- laptop and my old Windows XP SP3-computer. The problems were the same there.
View 2 Replies
View Related
Mar 20, 2013
how can I change a computer from one network to other in order to use FTP server
View 4 Replies
View Related
Sep 26, 2011
I have a question about the new nat implementation in an ASA 8.4. when I perform a "show nat" I get the following result:
1 (outside) to (inside) source dynamic any NAT-SSL-VPN_172.30.100.250 destination static 00B_172.30.100.0_24 00B_172.30.100.0_24
translate_hits = 26, untranslate_hits = 0
2 (inside) to (outside) source static LAN-HOST_172.30.100.11_LNX01 WAN-HOST_84.199.44.2_32_LNX01 service TCP-80-HTTP TCP-80-HTTP
translate_hits = 0, untranslate_hits = 0
Is it possible to change the order of the nat rules without removing and reapplying the rule on position 1 ? (both rules have to stay in section 1)
View 3 Replies
View Related
Aug 17, 2011
In what order the 8 cables go into the octal plug.The cable is a X.21.DTE 8 LEAD OCTAL part No 72-1100-01. The cables are not in numerical order (as in 0 to 7 as per the serial ports). I'm trying to trace cables and don't have a spare cable to examine. So far I think the order is 0,4,5,1, 2,6,7,3?
View 2 Replies
View Related
Nov 12, 2012
I am implementing traffic export on the WAN interface of my 3725 router. I use a dialer interface for PPPoE which is applied to the Fa0/0 interface. This dialer WAN interface has Zone Based Firewall, NAT Outside, ACLs applied to it, as well as IP Traffic Export for an IPS. In what order would each of these items process a packet? In other words, is the order something like ZBF, ACL, IP Traffic Export, then NAT? How would QoS fit into something like this as well? I am asking because I am wondering how much processing the packets receive before they are mirrored over to my IPS.
View 1 Replies
View Related
Oct 8, 2006
Is there a way to customize the order of the Groups in the drop down page on the login page?
Want to use a different group as default. Read over docs and not seeing a way to configure the login box dropdown order.
If it is not configurable, is it alphabetical on group name or the order they are configured ?
View 4 Replies
View Related
Nov 1, 2012
I recently install Windows8 Enterprise build 9200 on my Dell XPS L502X and everything is working fine so far except my modem. In device manager its installed properly but the network manager doesn't list it as an option to connect to (as it usually would in win7),
View 2 Replies
View Related
Jan 28, 2012
I have a Cisco Linksys WRT120N wireless router in one bedroom. On another bedroom which is hardly 15 feet away, I have set up my laptop to connect to it via a Cisco Linksys AE1000 wireless USB adapter. There are two thick walls between one bedroom and another.
Neverthess I find AE1000 dropping connection all the time. There are times I unplug the laptop and take into the same room as my router but it still doesn't connect. The wireless strength constantly varies from Very Good to Excellent but no matter what I try AE1000 never connects to it. If I restart my laptop, sometimes it does connect.
All in all its very frustrating that two Cisco products can't communicate effectively with each other.
P.S: I have both my ASUS tablet and my verizon droid both connecting to the wireless router from the same room as my laptop without any issues.
View 9 Replies
View Related
Dec 31, 2008
I purchased a WRT110 wireless router several weeks ago. Used it with my WPC55AG with no problems at all. I liked the wireless-N, so I decided to upgrade to a wireless-N notebook card and purchased a WPC100. I can always connect to the router with 100% signal strength. However, when trying to access the Internet, sometimes I can connect to websites, but I regularly get an error message that Internet Explorer cannot connect to the internet, even though the signal strength is still 100%.
Tried going back to my WPC55AG and do not get any connection error messages. Tried connecting to my router with my PSP and do not get any connection error messages. Connected to another wireless router that didn't have WPA or WEP using my WPC100 and didn't get any connection error messages..
View 5 Replies
View Related
May 1, 2011
I tried to update my firmware on my DIR 615 by clicking the check now button within the routers parameters and got the file DIR615C1_FW311NAB04.bin The update bombed. I have hardware ver. C1 Firmware ver. 3.11NA dated June 23, 2009.Should I try and install the other firmwares in subsequent order, i.e. ver 3.11NA (dated 7/15/2009), then ver. 3.12 and then ver. 3.13 Or should the latest and greatest cover them all?
dwest.Wireless to router. No factory reset. ISP Ser. Cable ISP Router. Stand Alone.Modem Make & Model. I have to get up for that one, will have to report back tomorrow.
View 4 Replies
View Related
Apr 2, 2012
I recently upgraded my 2811 router with an AC- IP power supply, and installed a HWIC-4ESW-POE, with an Inline Power Daughter Card (ILPM-4) installed on the HWIC.
The second I turned the router's power on, there was a spark and a burning smell. Everything still works, except POE. Examining the card, I see it caused a circuit on the ILPM-4 motherboard to blow, and there is black residue everywhere. This is a Genuine Cisco power supply, but why it's done this.
Furthermore, when the power supply was first installed, it had so much electricity (and I know this is why the card got toasted) that touching the end of the console cable or an Ethernet cable connected to the router, or even the router chassis, would cause you to get a small electric shock, like touching a mild electric fence. Clearly, the power supply I installed is "too-powerful", but it is a 2811-AC-IP and nothing should have caused this.
View 2 Replies
View Related
Dec 20, 2009
I bought the WMP600N because Linksys and Microsoft listed it as 'compatible' for Windows 7 x64. My experience:
- unstable and weak connection
- pings to websites like google.com drops, average: 1 out of 3
- low signal, on the same spot my three years old HP-laptop with 'a build in wireless card' has full signal strength in Windows 7
- it works well under Windows XP (32 bit)
I am convinced that drivers for the WMP600N are not ready for Window 7 x64. Linksys (or Ralink, which developed the chipset), release a proper driver for the WMP600N.
View 9 Replies
View Related
Feb 23, 2011
I'm using the WUSB54GSC on a IBM Desktop computer, not old, but not new by any means. We have wireless internet through Comcast, and my room is on the second floor. The router is on the first floor, but it's almost just underneath my room. The internet seems to connect completely fine, but it will disconnect at some things. For example, when I tried to go to mapquest, it was like it was flooding, and it dropped the internet connection. I also play games online, and when I play the actual game itself (GTAA/Online) it plays just fine, no lag, nothing like that, but when I try to connect to Teamspeak, when it's loading the channels after it connects, it just drops the connection..
View 1 Replies
View Related
Jan 24, 2013
I had this card working on this notebook with Windows XP, but with only 256mb ram it ran too slow. So I went back to 2000 on it. But I can't get the card to work, I've tried using the setup, the link light on the card does flash on and off. But in the linksys program just says no association with access point and says WPC54GS is inactive. I tried just installing the driver when it detects it but that didn't work. Also I try to start the wireless configuration and just get error 1747 the authentication service is unknown. What do I need to do to get the card working on here so I have internet access?
View 5 Replies
View Related
Nov 6, 2011
Every now and then my adapter won't be able to connect to the internet for a few minutes, and then it just comes back. This happens frequently, varying from every few minutes to every few hours. If I re-connect the adapter, though, a connection instantly comes back. There's no sign that it's lost connection, the taskbar still displays Internet access and a 5 bars, and the blue light on the adapting keeps flashing; but I just can't connect to the iternet at all.
View 1 Replies
View Related
Dec 9, 2011
I have the AE1000 adaptor on my wife's computer and direct wired on mine is the E2000.The e2000 is set to 2.4mhz and when connected to the wireless network, my wifes ae1000 shows it is connected at 144mbps.When I change the e2000 to 5.0 mhz and then my wife connects to the internet, she shows the ae1000 at 16-53 mbps. When I switch back to 2.4 she shows 144. I thought that when the e2000 is connected at 5.0 she should have a "faster connection".
View 1 Replies
View Related
Oct 1, 2010
I have the problem that my WUSB600N loses the connection to the internet after a few minutes. I boot the system and the wireless stick run impeccable. After a few minutes the windows 7 network icon show me a yellow exclamation mark and no more internet access is possible. When I unplug the WUSB600N from the system und plug it on again the internet connection is possible again and run then over houres without a problem.
View 8 Replies
View Related
Sep 8, 2011
i have a WUSBF54G that will connect to my router just fine. Right when the device is first plugged in there aren't any problems. I can ping my router, I can ping google.com. The browsers all work correctly, etc. But after a while, maybe 30 minutes (it varies) I lose the connection to the internet. I can still ping the router. I can ping other devices on my network. But I cannot ping any websites by DNS name or by IP address and any browser I use won't display any websites. I have other wired and wireless connections on this network that don't have any problems. I even unplugged this adapter and plugged it into a different computer and had similar results. The device is relatively new (maybe a month old, but only used a few times within that month, and the use that it did get is mostly from trying to troubleshoot this issue.) Both computers I have installed the device on are running Windows 7 Ultimate. Both computers have the latest drivers installed from this site:
[URL]
I have a netopia 3000 router and I have checked to see if the problem could be caused by this router but there is nothing out of the ordinary there. All of my troubleshooting has been using the Win 7 "network and sharing center" to connect. I couldn't get the linksys connection tool to work and actually, I noticed after reading this forum that the linksys wifi connection tool doesn't work with win 7 after all so I don't think using the built in win 7 wifi tools would cause the issue. Also, just to clarify, in an attempt to resolve the issue I have tried dynamically assigning an IP address for this connection and also a static IP address. Either method seemed to yield no results. It is a frustrating problem to say the least. I don't want to believe that the adaptor is faulty. As I said it is relatively new. Also, as I mentioned, when I first plug it in it will work correctly for about the first half hour or so before it will stop reaching the internet. I then have to physically unplug the device and plug it back in in order to correct the issue. I was thinking of creating some kind of script that will automatically disable the adapter every 30 minutes and then enable the adapter. I ran into another issue here though. If I disable the adaptor (either from device manager or from "Network Connections) the device will change status from "Not Connected" to "Disabled." So far so good. But then, when I go to enable the adaptor again the adaptor disappears from the list. It's as if it isn't plugged in any more. The only way to get it back is to physically unplug the device and physically plug it back in. How to "Enable" the device without it disappearing from the network adapter list.
View 1 Replies
View Related
Mar 25, 2011
i have intermittent connectivity on the 2nd router that was installed on the network in order to extend range. 2nd router is connected to the original wireless router by an ethernet cable.
View 5 Replies
View Related
Jan 10, 2011
How can I connect Two ISPs on My LAN simultaneously in order to boost my internet connections?
View 1 Replies
View Related
May 27, 2013
i'm working on a QoS troubleshooting issue, I want to know the order how the QoS ACLs will be getting processed.For example I have configured the ACLs AF11, AF12 and AF13, in what order switch will process the ACL? does it in a ascending order fashion?
View 1 Replies
View Related
Aug 22, 2012
I was wondering to understand if there is an specific license in order to enable NBAR2 in my ISRG2 892 with IOS 15.2(3)T. If not, what is the basic license I need to have for NBAR2 ?
View 5 Replies
View Related
May 24, 2012
I have got two 878 integrated services routers and I need to configure them as transparent bridges in order to connect 2 remote sites over ATM.
As I'm testing the topology, I configured two switches (representing the sites) at each end with a VTP domain. VTP works while the switches are connected directly with eachother, but it won't work with the bridges in the middle. [code]
View 6 Replies
View Related
