how to conntect an old PC to a wireless broadband home network. I had set up wireless broadband at home on a laptop. Next I added a second laptop to the network just by entering the password that I had used when first setting up the wireless service. This PC does not have a wireless adapter nor ethernet ports.if addition of a wireless adapter card into a vacant motherboard PCI slot would be sufficient to extend internet access to this PC.
View 5 RepliesI have a e4200 Linksys upstairs and the range in parts of house is weak weak. I need more access points. Can I add another router downstairs on another cat5 and make it act as access point? What other options?
View 4 Replies View RelatedAt the moment i have 3 routers across the house, each acting as a wifi access point.My problem comes to when i use my phone or laptop, it connect to a random access point doesn't matter of the signal.Is it possible to combine 3 routers as one access point. So that i would connect to one access instead of 1of 3 access points, that would be a strong wifi signal no matter when i am in the house. Something similar to what bit malls or stores have.I have looked at wi-fi repeaters, but they just repeat the wifi and make new access point.
View 2 Replies View RelatedIm in abit of trouble trying to setup a wireless network. Part of the problem is that I am many miles away and I've never setup a wifi-netork involving more than one device, that device being a router.I connected the TL-WA901ND to the router(a Thomson tg787) located in the house, this router couldn't be used simply because the SSID and its password is locked, and we sometimes have people renting the bottom floor and we would prefer a better SSID and a changable password for the network. The first TL-WA901ND(will call this one TL1(AP) from now on, the other being TL2(RP)) is set to operate as Access Point, having a different SSID and password for the network, and it works great. However, when I try to set the other one, TL2(RP) to repeater mode, with the TL1(AP) and that SSID/MAC as "target", it doesn't seem to work. I've tried using bot the repeater mode and the universal repeater mode but none of them seem to do the job.Is is possible to repeat the signal of an access point or does it have to be a router? The SSID and the WPAkey of the repeater is set to the same as the access point, is that correct?The access point is not the one handing out IP-addresses, the router is still acting as the DHCP-server, is that correct?
View 1 Replies View RelatedI have a Linksys wireless router in my basement and I want to extend coverage upstair. I have a office upstairs which has a ethernet cable that is plugged into my router in the basement, can I connect a Linksys Wireless G WAP54G access point to that ethernet cable and thus have a extender upstair?
View 1 Replies View RelatedI have no clue what kind of brand is the outdoor antenna. It plugs into a wap54g and I need an extension cable to my antenna, only like 6 feet, where can i buy this?
View 1 Replies View RelatedI plan to extend the wireless signal for RV220W as a wireless access points now. Can we use lower end model instead of another RV220W?
View 2 Replies View RelatedI currently have a Linksys WRT310N as my primary router/wireless device. I am not getting coverage in my entire home. I was considering purchasing the Linksys E4200 and using the WRT310N as an access point in another part of my house to extend my wireless network. From all of the research and reading I have been doing, it seems that I must connect the WRT310N to the E4200 if I want to use it as an access point. Is this the only way? I have no way to connect the WRT310N to the soon-to-be E4200 unless I run an Ethernet cable across the floor. My goal is to use the WRT310N as a wireless access point without having it wired to the E4200, if at all possible. If this is not, what other way could I go about doing this type of setup?
View 3 Replies View Relatedhow do i extend wireless range and increase signal to granny flat for internet? from the modem to the granny flat about 15m+, i tested it with my laptop get 3 green signal and on inSSID get around 74+ RSSI but with Asus-n13 and mini Tp Link wireless USB adapter get above 79-80 RSSI. don't know why but i get signal for surfing internet on laptop but randomly get drop out. household gave me $200 to improve the signal....
View 4 Replies View Relatedhow do i setup a wrt54g router as a wireless access point to extend wifi signal from e3200 which is broadcasting the internet?
everyone keeps saying to remove the stock firmware and instal the dd-wrt firmare to do this. can i do this with the stock firmware?
I am not sure if what I am trying to accomplish is possible. On my internal network I have the following VLANs setup (102, 104, 106) and they map one to one to a subnet (ie: 102 = 192.168.102.0/23, 104 = 192.168.104.0/24, etc).All interVLAN routing is done on a 3560 via vlan SVI. Connected to the 3560 via a routed port is a ASA 5510. The routed port has IP 192.168.100.1 and the ASA interface on the other side of that routed port has IP 192.168.100.2. I use 802.1x on the wired network to assign users (based on their department) into a specific VLAN. I want to extend this concept to Remote VPN access. Therefore I setup multiple Group Policies (policy is applied based on an LDAP attribute) where each policy defines a different DHCP scope. This has successfully allowed me to login wtih different users who get assigned to different Group policies and they obtain the correct DHCP IP address from the internal DHCP server (ie: an engineering person logins remotely and gets an IP in 192.168.102.0 range). However the issue (and as I was planning this out I knew this would come up) is that traffic can be routed out from the VPN client to its destination but there is no return path.
View 3 Replies View Relatedwhat i am after is, a way to extend my internet in a room that cant connect wireless. i want to be able to connect my ipod touch/ nokia phone / ipad on my home network. i have wireless in the house, But, because of the insulation in the walls and ceiling in this room(kingspan, with the silver foil on it) i cannot get a signal, i am wanting to know if it is possible to some how use the wired connection from my pc in the room and add a wireless dongle(usb) and some how get it to share the connection?
View 5 Replies View RelatedI have a broadband connection through a TV cable connection to a ISP provided modem/wireless box. I have a wireless network set up already from this box. I wanted to extend the wireless network to a hard to reach area so i bought a seperate router (d-Link DIR-615 revE3).
I connected one of the 4 LAN outputs from the modem to the router's "Internet" input. Windows 7 detected the new router's wireless network and guided me through setting up a name and password for it. However there is actualy no internet access on this network even though it's directly connected to the modem.I was thinking that i wanted to just extend the original wireless network but a new network is fine if only it would use the internet from its LAN connection... a desktop computer has connected from the same LAN output of the modem without any security and been able to access the internet from it.
I Have a 2 Access Points First One : TP-Link TL-WR542g V7 and this is a Picture of it: url...i Have my Router on The First floor and My Wireless Enabled on it With WEP Encryption.i Need To Extend The Coverage to The 2nd Floor,By Using one Of my 2 AP's.Setting up my AP To Receive the Wireless Signal From My Router And Re-send it To My Laptop.."Wireless"..So i can Leave it only With AC Power ..And Still Streaming The Signal While my Laptop Receiving.
View 1 Replies View RelatedMy b/g/n router is at one end of the house and on the second floor needs to be. I currently have a b/g/n wireless bridge hooked to a LAN port of an b/g/n router that I am using as an access point almost in the center of the house, about thirty feet away with one wall between them. I get good connection speed on an Internet TV that's about 7 feet below the access point with one floor/ceiling between. I get a reliable but slow connection to an Internet TV that is about 20 feet from the access point with two walls between. I get intermittent, slow connections with portable devices near the opposite end of the house on the first floor. Measured horizontally, they are within 15 feet of the upstairs TV that has a slow connection and about 9 feet below it.
The ceiling of my unfinished basement stairwell is a few feet below my router. I am thinking of putting a wireless bridge in the stairwell and connecting it with ethernet cable to an access point located in the crawl space, which is very dry, under the house directly below the upstairs Internet TV. It would be about 12 feet below the TV with a floor and a ceiling/floor between. That location would put it within 15 feet of the wireless devices on the far end of the house that now have a poor connection, with only a floor between. My primary goal is to get a better connection for them, but I'm hoping for a better one to the upstairs TV. My house is of frame construction with mostly plaster interior walls.
I want to use a POE access point under the house because I think it would be easier and safer than running a long extension cord. Looking at POE devices in catalogs, it is often not clear to me whether the device in question expects to be powered over ethernet or expects to power other devices over ethernet.
I have the following questions:
Does my plan sound feasible, and would it be expected to accomplish what I want?
How can I be sure that, when I order a POE access point, it expects to receive power over ethernet, not provide it?
Can POE devices be cascaded? If I do this and find that I did not get the coverage I hoped and, therefore, want to add another POE AP, can I add a POE hub or switch and run cable from it to the additional POE AP? If so, is there any particular monclature for devices that expect to both receive and provide POE? Can such devices receive and provide over any port, or do they have to receive power on a designated one and provide it to the others?
We own two houses next door to each other and I have the first 655 set up as WAP, wired to second in other house as a range extender. Works perfectly. I would like to add a third 655 (wired to the second) to extend my range further.
View 5 Replies View RelatedI have a couple of computers that are out of range of my router so I came up with a unique solution. I have an old laptop with 2 wireless cards that I put halfway between. It is working but I have a few oddities. First of all, the out of range computer is connected to another wireless router that several laptops and another (wired) PC connect to. It has ICS (Windows XP internet connect sharing) enabled. This rules out using ICS on the laptop as 2 pc's would have the address of 192.168.0.1.
View 1 Replies View Relatedmy screen goes blank if not used after about 10 mins how do i extend time?
View 1 Replies View RelatedI'm trying to extend the range of my wireless network from my house to my workshop, which is about 600 feet away. There are no trees or other objects in between the two buildings. how I could boost my wireless signal to reach that far?
View 1 Replies View Relatedim just want to ask a favor if you can guide me to set up or configure a router repeater to extend my wifi at my home. i dont have a specific brand of repeater yet.. im planning to buy but i have no idea how to set up a repeater by myself.
View 1 Replies View RelatedMy friend has an internet connection and Wifi, it reaches my room but with poor signal, is there any way I can strengthen up the signal?
View 1 Replies View Relatedcan you extend computer speaker wire to use in another room?
View 1 Replies View RelatedHow do I extend my wifi network?I have a Dlink DIR 615....
View 5 Replies View RelatedI get 10% signal in my bedroom using WEP2 and I would like to boost this to at least 50%
1) I have 2 DIR-655 Wireless N routers, both functional.
2) The first router is on the other side of the house from my room
3) The second router is not in use at all ... I'd like to take advantage of it
4) I have an Ethernet drop in my bedroom that runs under the house to the first router. I have a switch on that drop and use it for my Sony / Netflix box ...
I have been told that the DIR-655 cannot be used as a repeater. Can I not take advantage of the 2nd router to boost my signal in any way?
Ground floor: My ISP's wireless router and an 8-port switch. For wireless communication I use the ISP's Wifi and the 8-port switch is used for wired rj45 sockets around the house.
1st Floor: I have a TP-LINK TL-WR740N Wireless Lite N Router 150 MBps which I connected to a socket and have a PC connect with wire on it and also used for Wifi. The Wifi network I setup on the 1st floor is different than the one on the ground floor (2 routers).
At the first floor I have the problem that in other bedrooms far from the router the Wifi signal (either gets lost) or it's very low. So I bought a TP-LINK TL-WA701ND Wireless N Access Point 150MBps which I configured as universal repeater.
The access point supports only WEP encryption when used as repeater/universal repeater so I changed the wifi of the router to WEP with ASCII with 128bit character length and established the connection.The most important now is that even though the Wifi signal in the bedroom with the AP is full, when I switch off the wifi of the iPad and back on, it is not connecting to the internet. Yesterday I noticed that it was giving me the ethernet card IP (169.…). I went close to the router with the iPhone, got connected and when came back to the room with the AP it was working but the iPad is not working.
which will can extend the signal strength? changing antennas, put a wireless amplifier or buy ASUS 66U??change TPLink TL-WR1043ND to ASUS 66U ??? ASUS 66U is best to TPLink TL-WR1043ND and can extend the signal strength by up to twice the distance?
View 1 Replies View RelatedI have a new Siemens router and have set up my old LinkSys router as a switch (set DNS outside the IP range of the primary router, disabled DHCP server, connect LAN to LAN port).The SSIDs are still different. As a result each device now sees 2 networks and although internet GW is available from either connection, not al resources are shared across the network. There is one driveshare (with wired connection to the secondary switch) which cannot be seen by some of the wireless resources on the same secondary network.Questions:1. How can I set up the NW config such that it is seen and behaves like one physical network, anbd roaming devices pick up the signal from the strongest access point?
View 3 Replies View RelatedHow can i use a router to extend the ip addresses of a separate network? I have been given a subnet mask of 255.255.255.248 which has given me 6 ip addresses to access the internet. How can i use a router to allocate extra ip addresses and route them to the internet ?
View 1 Replies View Relatedi have linksys modem modell wag200g annex-A and stc modem (saudi Telecom company) how can i expand wifi signal to other room
View 1 Replies View RelatedI have a network of one router which servers both LAN and wifi, my laptop can only use wifi to connect but the range of the router doesn't reach the third floor. I need a way to either extend or create a second hot spot but I'm not sure whether to use a repeater, a hub or a switch? this is my first time dealing with a network
View 3 Replies View RelatedI have set up a home network with Time Capsule as the primary router. I would like to use my WRTG54GL to connect to the network via ethernet and extend it for wireless access at the opposite end of my house. I changed the settings to disable the DHCP server, I named the network the same as the Time Capsule and duplicated security mode and password. I can connect with my laptop, but it initially connects with full internet access, but after about 10 seconds, I can see Airport searching for a network. It reconnects, but for about 45 seconds I have no internet access and then access returns and works fine. On my iPad, however, although it shows I am connected to the network, there is no signal indicator at the top of the screen, and all connectivity seems to be through 3G -- not the network. I assume there is a setting on the Linksys that needs changing, but I can't figure out what it is.
View 10 Replies View Relatedset up the wireless network at a friend's house, which is a large solid-brick house that winds from one end to the other. The current location of where the cable comes into the house is unfortunately on the far-left end of the house, which means that the right end of the house receives no signal from their DIR-825 wireless N router.
What I've been looking into is the best way to wirelessly extend the wireless signal to the other end of the house. It seems straightforward enough to use an ethernet cable and access point to extend a wireless network, but that is not really a good option for this house. After reading many forum posts (and not being an expert myself) it seems like it may be possible to wirelessly extend the wireless network with another router, although it appeared that this is much less common (if at all possible) with wireless N routers.
what device I need to accomplish what I've described above? Another router, or some kind of access point/bridge? I saw at least one rather expensive wireless N repeater online (a Hawking brand, I believe) but was hoping to avoid that option initially, but if that is the only way to go then so be it :-)
I have a Belkin F6D4230-4 Enhanced N150 router. Would it be advisable to add a range extender to hit weak signal areas or simply upgrade to a more powerful router?
View 1 Replies View Related