I just got this wireless notebook card off of ebay, and it did not come with a cd. After just plugging it in it would not install, so then I downloaded the drivers and transfered them to my laptop through a usb drive. I setup the program the best I could and now it says "WPC54G not installed" and "No association with Access Point" on the link information page. How I can install this wireless card?
View 5 RepliesI'm trying to install a WMP54G PCI Version 4.1 in my Windows 2000 Pro SP4 computer. I ran the setup cd before installing the card, then took out the disk. After installing the card and powering the computer, the Available Wireless Network screen didn't appear. I also didn't get the Network Monitor icon on the taskbar. Network Monitor appears in the start menu, but can't be started. Device Manager says the card is working properly and there are no conflicts.
I uninstalled the software, removed the card, and repeated the installation process with the same end result. The card light blinks like it is receiving data. I'm using a Linksys WRT54G2 router. Both my desktop (W7) and my laptop (Vista) connect just fine. How can I get my W2K computer on the network?
I run the CD setup disk and the driver install correctly.In the "Connecting the Adapter" screen I click next before connecting the adapter,the setup screen just close with out any notification and no icons on the system tray.I shut down the machine, insert the adapter and power on the machine,now I have the monitor icon and a wireless connection icon in the system tray (the Power led is green and the Link led isblink),when I double click on the monitor icon I got the following screen: no available wireless and the refresh, connect and manual setup are disabled.when I click on the "open the monitor" form the right click menu I got the following screen: also nothing to do on this screen.so I think it's was because I don't have any wi-fi around me, I shutdown the computer raise my wi-fi andrestart the machine, now the led in the same status but the system tray icons didn't appears and when Itry to open it from the menu it's run for few seconds without any screen and disappear.
View 6 Replies View RelatedWhere can i find driver for WPC54G ver.4 (FOUR). I looked for on official site, and there are drivers only for ver. 1, 2, 3, 3.1, 5, and 7! Where can i find drivers for ver.4?
My OS is MS Windows 2000 SP4.
I have a WPC54G version 4 wireless-G notebook adapter. I cannot find anywhere even here the driver for this device? I read the forums and have been googling all morning and I found one topic that said that version 3 (Vista compatible) WPC54G_V31_driver_4.100.15.5_vista.exe..will work with ver 4. I have tried it and my adapter will still not see the files in the extracted folder. There's 5 files in the folder and when I do the hardware/update driver method it won't see the drivers. I have tried all the other version and none will load??
How can I get this driver to work with my Windows XP? I don't have the CD anymore.
I have a WPC54G ver. 2 adapter I am trying to get to work on a thinkpad T22 running W2kPRO with all the SPs and updates installed. The power light comes on, but the link light does not. I am using a Linksys WRT54GS wireless router. The monitor icon shows in the taskbar and when I open it, it says the adapter is inactive. I have tried several time to download and install the driver for the Linksys site. It seems to install OK, but when I go back and check the Drivers tab to verify that the driver version has changed to 3.20.21.0, it is still version 6.0.0.18.
View 4 Replies View RelatedI am trying to install a WPC54G adapter in a Compaq EVO N610C Laptop with Windows XP SP3 and it has a Texas Instrument PCI-1420 CardBus Controller. Adapter is inactive. I have uninstalled, reinstalled, download updated drivers from Linksys.
View 1 Replies View RelatedHave an old laptop running XPSP2 with a WPC54G V1.2 card that I use for email when traveling. Had no problems accessing my old home network that ran off of a WRT54G V 5.0 wireless router, nor with any of the "motel wireless networks" when I travel. I changed ISPs and now have an Actiontec PK5000 wireless router.
When I attempt to connect I get an error message "unable to acquire network address."
This new router has the following 64 bit and 128 bit settings
wpa-wpa2 personal
wpa personal
wpa2 personal
wep
security off
Using any of the security settings I get the error. Turning off security allows me to connect fine.
I realize this is a pretty old wireless card so is it possible it doesn't work with the current encryption standards but I would have thought that wep would have worked. The driver for the card is V3.3.15.0 which is also old. Would updating the driver work and if so what driver? If a new card is the only way any recommendations for an inexpensive card?
I've spent several hours of my life trying to rectify this silly problem without peace. Maybe one of you can enlighten me. I've got a Win98 laptop and have loaded the driver specified from the Linksys website. The software from the website under "Version 1" downloads a file entitled "...driver utility v3.1." I've installed and uninstalled it 3 times with restarts inbetween. Each time Device Mngr shows it is installed correctly but the "inactive" status persists. I get a "Power" light indicator but never the "Link" indicator on the adapter. I do not have a firewall or any other software that would interfere with the access point I have at my home (which works just fine with my Vista laptop). Furthermore, the wireless router is not secured either, so it is wide open and broadcasting. But as I said, the adaptor isn't even showing as "active" so all that stuff is moot I guess. I can not upgrade the laptop to another OS, it is an antique from 1999 and can't cut the mustard with the RAM and processor speed it has. Besides, it should work just fine with Win98 anyway.
View 4 Replies View RelatedI use a WPC54G wireless adaptor to connect a laptop to my home network. I just replaced a WRT54G2 router with a Cisco Valet router.When I start up the laptop, the wireless adaptor's Monitor configuration takes priority over Windows XP wireless configuration, but the Cisco Valet does not recognize the Monitor. If I disable the Monitor, everything is fine until I reboot, and then the Monitor again prevents connecting to the router.
How do I permanently disable the Monitor software so that the laptop will default to the Windows XP wireless configuration settings?
I have a ThinkPad running 2000PRO that I just installed a WPX54G Notebook Adapter. After installing and restarting the computer I get a window saying External exception E06D7363. Also, when I go into configure it says the adapter is inactive. When the computer first starts up the icon for the adapter is green then turns gray.
View 9 Replies View RelatedI have the WPC54G , used on Sony Vaio, Windows XP Home Edition Version 2002 and use a Novatel Wireless MiFi 2200 Mobile Hotspot. Recently had system crash--reinstalled through recovery discs and all current Windows Update (SP3), as well as the WPC54G The WPC54G worked with various WiFi Networks and the MiFi2200 Device before crash. After "recovery", it recognize WiFi Networks, however; it does not recognize my network established through the Novatel Wireless MiFi 2200 Device. (Note: the MiFi Device is working because other computer/devices are gaining access to internet.
View 7 Replies View RelatedI have a Packard Bell Laptop using Windows XP OS and doesn't have Wireless Connection. So long ago i bought a Linksys by Cisco Wireless-G Notebook Adapter WPC54G v.1.2 but didn't have time to set it up or use it for travelling conditions. A couple years later when i came back to check on the laptop, i noticed that i lost the setup CD. So i went on the Linksys website and looked for the driver the download. On the back of the Adapter(card) it says it is version 1.2. But this version is unavailable on the Linksys Website. I could only find v.1, 2,3,3.1 and 7. v.1 gives a driver of v3.1 etc... AND NOT VICE-VERSA.So first when i inserted the card into the slot , the PC didnt detect it. It only detected it rarely if i insert another driver (eg: USB..). And so a window would pop up to install but i didnt know what to do there. When i downloaded the v.1 driver from the website and installed it, it seemed not the detect the card either, it would just say searching for wireless, but that's it. It would keep searching for hours even when im next to the router.finally, only the Power led light on the card is lit up but not the "Link" led.
View 1 Replies View RelatedHow to install model WUSB54GSC.
View 5 Replies View RelatedI recently re-installed Windows on my PC, and I had the Wireless-G PCI Adapter installed before I done the re-installation.Now I've re-installed Windows, the adapter doesn't work. Do I have to re-do the whole process again? Also, I didn't actually install it myself, so any detailed step-by-step tutorial?
View 3 Replies View RelatedI had a hard drive failure recently and replaced my HDD with an identical HDD (WD 500 AAKS) and did a restore from my WD Passport Essential. Everything works as before except I can't install my AE1000 wireless adapter. The OS recognizes the new hardware and I attempt instalation form the setup CD. Istallation goes until it gets to the "Installing" step and then it just stays there forever until it comes back with an error. I am accessing the internet now through a cat 5 ethernet hook-up.
View 2 Replies View RelatedWhat i have to download and where to download some kind of program that will allow me to run/install this on my MAC. Model: AE2500
View 1 Replies View RelatedI need to download XP drivers for my WUSB54GC ver3 Wireless Adapter. I have lost the CD (or can't find it at least) and on the site there seem to be only Vista/windows 7 drivers for the version 3. Will downloading the version 2 XP drivers do? Or should I do something else?
View 1 Replies View RelatedHow do i install the WMP300N without the installation CD ? I bought a new PC and i cant find the CD?
View 7 Replies View Relatedi cant install it in the windows 8 its tall me 'the data is invold' and i try all put out and bring in all?
View 2 Replies View RelatedWe just bought a new computer and I am trying to move things around. Does anyone have the original install CD for trhe WUSB54AG? I can't find mine and the driver is no longer online.
View 3 Replies View RelatedI've tried to connect the usb adapter with an Acer Aspire 7736ZG, installed with Windows 7 64bit edition. Well, I *can't*.
- I started the CD installation and when prompted, I've connected the USB stick. Well, the stick couldn't be detected, and the installation couldn't continue.
- Then, I used the Windows7 drivers and managed to install the device (device manager, sees the device normally). But, the CD still couldn't continue the installation of extra software.
- Ok, no linksys software - no big deal. I would use the Windosw wireless management program. NO! The card seems not be present, and the only wireless connections I get, is by the onboard 802.11n card of the laptop (don't ask why I bought an extra 802.11n card).
- Nothing happens by disabling the onboard 802.11n card and trying all over again.
- If I go to the connection and sharing center and select "change setting of adapter", well, my expensive and cisco-super-duper card, isn't there, and I can only find the Atheros ARB93 Wireless card and the local (wired) adapter.
So, to sum up, 64bit driver seems to be installed correctly on the device manager (as proposed on other threads) but the adapter is not present on the system. How cool is that?
I just got a WPC600N wireless card working with XP Service Pack 3.Do NOT install the software, just slide the card in.Windows will ask for the drivers, point it to the CD or where you downloaded them.
View 1 Replies View RelatedI have 1 computer a HP system with Ubuntu 11.04 installation.I would like to install the Linksys WUSB600N-AS (V2) into the Ubuntu but the drivers and instruction is very confusing.tell me which drivers to download and how to install.
View 1 Replies View RelatedI need the Windows XP WUSB54GC V.3 Driver!
All of the other threads on this forum have expired links to the driver. Where can I find it? I've looked for hours & the cisco website offers nothing for Windows XP for WUSB54GC Version 3
I am trying to install the Ae1200 on my notebook (windowsXP), which doesn't have a cd drive. I downloaded the driver from cisco page, and also copied setup disc from a 2nd comp onto a usb drive. Using both options, the wizards starts correctly, but then ends with error message saying "cannot find specified file"
View 2 Replies View Relatedwhen i install using the CD it stops after i plug in the adapter with a 211 error telling me to replug it in blah blah. i tried to manually install the drivers from the CD. it dose this successfully but it wont pick up any net works. and when i use the network app that came with the CD it tells me it is not installed right. what is going on it says on the box windows vista compatible.
View 1 Replies View RelatedI am running Windows 7 with the WUSB600N (v.2). Here is how I got it to work.The driver support is not a .exe. You will have to install it yourself...but it's not a big deal.Download the Windows 7 driver for your OS version from the Linksys Support page.Save it to the desktop and then unzip it to the desktop so you can find it easier.Once unzipped you will see 3 folders: Mac, Win7 32 and Win7 64. Choose accordingly.What I did was install it through the "Device Manager". (Right click "My Computer", choose "Manage", then Device Manager",or use the "Search Bar under the Start Menu...whatever. Once you are in the Device Manager...
1. Make sure your WUSB600N is inserted in your computer.
2. Navigate down to "Network Adapters" If you see your WUSB600N adapter...great! Your halfway home!
3. Right click on the "Linksys WUSB600N Adapter.
4. Choose the option to " Update Driver Software"
5. Choose "Browse My Computer for Software"
6. Navigate to the desktop and choose the folder that contains the name of your Windows 7 platform.
7. It should update but, HOLD ON! We are not done yet!!!
In order for it to start transmitting in that shiny new 5GHZ band, you must go into "Network and Sharing Center". Once there, look on the left hand side of the main window and you will see "Change adapter settings"Go there. You should see here that your existing adapter is still working (enabled) and your new Linksys WUSB600N has a big fat red "X" under it (disabled).Right click on your existing adapter and choose, "DISABLE".Then, right click on the WUSB600N adapter and choose "ENABLE".The last thing you should have to do is choose the network you want to connect to (for me it was the 5GHZ one) ..and Viola!!
Whenever I try to install the drivers for the adapter normally, Windows 7x64 gives me a message that the device name "Compact Wireless-G USB Network Adapter" already exists and is in use, preventing me from installing the wireless driver properly. In order to get around it, I changed all "Compact Wireless-G USB Network Adapter" fields into "Compact Wireless-G USB Network Adapter B" in the netr28ux.inf file to make the driver install under a different name.I tried everything I can to remove all evidence of linksys drivers from my computer, uninstalling and removing driverstore with pnputil.exe, but I cannot seem to find the originating files to uninstall.For now the way I edited the netr28ux.inf file works, but I'd rather be able to install the driver as intended.
View 6 Replies View RelatedI purchased the AE1000 wireless adapter for use with my Linksys WRT54G router. I first tried to install by loading the CD, which went so far as the "Insert your adapter into a USB port" screen. The Windows "processing" circle spun for about twenty minutes, then I was prompted to "insert the wireless adapter" once more. Rinse, repeat. I absolutely cannot get past this step. I scoured the web for an answer and turned up little. I uninstalled my antivirus and firewall software, made certain that files associated with my prior adapter were removed, tried varying USB ports (all 2.0) on my desktop, and had no success. Today, I exchanged the adapter for a replacement, and I'm encountering all of the same difficulties.
View 6 Replies View RelatedI recently reformatted my HD and when i went to install my wireless adapter i realized i had lost my Install CD for my WUSB54G Ver. 4 USB wireless adapter. Is there anywhere to download the install program?(i'm running windows xp)
View 4 Replies View RelatedI need to install AE1200 on fedora machine.
View 9 Replies View RelatedI bought a AE2500 adapter recently and attempted to install the Cisco Connect software. It gets to the point of connecting the device to the wireless, then crashes. I noticed that as I plugged the device in, it was recognised and activated without running the software at all; at the time of the software trying to connect the device, it's already connected.Just in case it was a matter of an old version of the driver and Cisco Connect software, I went online to the website and downloaded both the most recent driver and the latest version of Cisco Connect. The Cisco Connect crashed just like the version on the CD, and the driver said it was already the latest version and wouldn't install.So I tried the direct chat option. I spoke to two people. One of them lead me to give them a lot of information, then began asking me about my router... and promptly forgot about the adapter. They even had me on the path to resetting and installing software for the router I'm connected to, which isn't mine. Then the chat session crashed. why the Cisco Connect program keeps repeatedly crashing, and how I can stop it from doing so. As it stands, I think the adapter is overloading the memory on my computer and causing blue screens; I've been getting them ever since I connected the adapter. I think it might have something to do with my computer automatically detecting and activating the device when it's plugged in, but I'm not sure.
View 5 Replies View Related