Linksys Wireless Router :: Random Dropping Of Connection To WRT120N?
Nov 15, 2011
I have a WRT120N, and have set up connections like this:
Desktop PC: Hardwired Ethernet
Laptop: Wireless
Xbox 360 (1): Ethernet
Xbox360 (2): Wireless
Networked Printer: Wireless
The hardwired connections are fine, but at random the Printer, laptop and wireless Xbox connections will drop out and i'll have to reboot the router to get it working again. I've tried everything I know of (i.e., Static IP, Port Forwarding) as well as a factory reset, but I continue to have this issue.
View 1 Replies
ADVERTISEMENT
Jul 16, 2011
I have an internet connection of the speed of 384 kbps, settings are default i changed nothing. firmware is updated. i'm using wireless connection.any settings you will recommend like in MTU, Beacon Interval, RTS and fragmentation?
View 2 Replies
View Related
Nov 28, 2010
My wireless router will work for 6- 8hrs then drop the internet connection. I have to cycle the modem and router several times to restore the connection. I am also using a Netgear Access Point.
I am using:
Charter High Speed Internet
Motorola Modem
Cisco Model WRT120N Router
SETTINGS
Mode- Mixed
Channel Width- Auto 20MHz or 40MHz
Security- WPA2 Personal
SSID Broadcast- Disabled
Firmware Version v1.0.04
Connection Type- Auto Conf DHCP
Beacon Interval - 50
Fragmentation Threshold 2304
RTS Threshold 2304
All other setting are at factory default.When I unplug the modem from the router and plug it into the desk top I have internet service.
View 6 Replies
View Related
Feb 8, 2012
Had an E4200 for a couple of months now and have not been able to resolve an issue with the router dropping an Apple iPad 2 at random times.The E4200 is replacing a Cisco Aironet 1200, which never dropped any clients, iPad 2 or others, and never displayed any of the issues below.
TECH DETAILS:The E4200 is being used purely as an access point. All extras are not in use and are disabled.
Firmware 1.0.03
Hardware version 1.
BASIC ISSUE:The E4200 drops an Apple iPad 2 off the 2.4 Ghz Mixed (B, G, N) network. The user must then select the network to rejoin. Rejoining occurs without incident. The same issue occurs when the network is restricted to B, G. The drops occur at what appears to be random intervals - sometimes 10 minutes apart, sometimes hours apart. We can have as many as 6 drops in an hour. A ping to the apple ipad shows the device stops responding to pings about 10 seconds before the user is prompted to rejoin a network. Meanwhile, a ping to the E4200 itself from a laptop connected via the E4200 on the same radio as the ipad continues to work without fail during this incident.
1. The iPad 2's cannot connect to the 5Ghz radio. I believe iPad 2's are supposed to support 5Ghz.
2. Both our Apple TVs do not connect to the 5Ghz radio: they fail with a "There was an error connecting to the network. Check your settings and try again. (-3914)" error. Apple TV supports 5Ghz.
3. The admin interface for the E4200 is very slow sometimes. Probably over 20 seconds to render some pages when it gets really bad. As a comparison, Internet-based pages on fast sites that delivered via the E4200 itself load in less than 2 seconds.
4. The HTTPS version of the admin interface can only be connected to via Safari browers. Both Internet Explorer 9 and Chrome 16 fail to connect with a "Connection reset" error. In Chome, it says "Error 101 (net::ERR_CONNECTION_RESET): The connection was reset." This is across multiple devices. There is no issue with straight HTTP.
All other devices - including Macs and PCs - connect fine with the E4200 on both 5Ghz and 2.4 Ghz radios, even if they cannot access its admin interface via HTTPS.I've presented quite a few issues above, but the main one is the drop outs for the iPad 2 devices. I'd present logs on drops, but the thing doesn't record any useful logs.
Basic wireless config:
5Ghz:
Network Mode: Wireless-N Only
Channel width: Auto (20 or 40 Mhz)
Channel: Auto (DFS)
SSID Broadcast: Enabled
[URL]
View 9 Replies
View Related
Oct 13, 2011
I am trying to use my WRT120n as access device for an IP Centrex service using SIP protocol. My SIP phone is located right behind the router.My problem is sometimes the router is dropping incoming calls because signalling packets are fragmented at IP level. So I cannot receive those calls.Is there a way to enable the router to accept these packets?
View 9 Replies
View Related
Jun 27, 2011
I have a toshiba a215-s7437. I bought this router upgrading from the usual netgear router that everyone and there mother has(wrt54g or something?). The routers are in the same exact spot...less than 6 feet from the computer with no obstructions. No matter WHAT i do, even if i put the router on top of the laptop keyboard, over time, usually a matter of minutes, it starts dropping my link speed. My old netgear ever went below 54, EVER. Even if i was out on the porch.It will connect at 54 mbps, then go to 36, etc etc until we get to 1mbps. I have had other friends bring laptops over, same exact thing happens to them. I am viewing the link speed through windows task manager to get these readings. Though i can't see the link speed on my android phone or xbox, it seems over time they get slower also. I have tried googling the hell out of this issue to no avail. I do have the latest firmware. I have also tried searching these cisco forums and have not found any topics pertaining to this (maybe i just suck at searching). I have comcast at 15mbps and i do know that whether it is 54 or 36, it's not gonna be any faster. But just the fact that it falls the whole way to 1 is not acceptable. My fix for this at the moment is just disconnecting and reconnecting real quick, and i always start back out at 54 mbps. Sometimes I will get lucky and it will stay at that point for 20-30 min?
View 8 Replies
View Related
Apr 4, 2013
My DIR 651 randomly drops connection, is not set for IP fragments (error on PS3 even though I set MTU), and has a flashing green globe compared to my other DLink router which has a solid green globe (replaced with DIR 651). I have BHN Road Runner Turbo (Speeds of 30mb/2mb) and my modem (supplied by ISP) is a Motorola SB5100.
View 10 Replies
View Related
Sep 3, 2011
I have several computers and printers connected to a WRT120N router which is connected to 10mpbs DSL. The computers are all running WIN7 and are hardwired to the router. On the one PC, it keeps losing network connection. I've tried upgrading the router's firmware, reset, etc. to no avail.
I think it may be related to the same IP address being assigned to multiple machines connected to the router. Is there a way to set specific IP addresses to each item connected to the router to see?
View 1 Replies
View Related
Aug 21, 2011
I can hardwire to my modem and get internet but when I try using the router it can't find it. Everything was fine yesterady with router. What I noticed is when I plug the router in to reset it before plugging any ethernet cables in the port 1&4 lights were blinking like there was activity
View 1 Replies
View Related
Nov 24, 2009
I recently purchased the WRT-120N router for my home network. The wireless is set to mixed mode, with WPA Personal encryption, with key renewal set at the default 3600 seconds. My problem is that the connection is not stable. I can be connected with one computer, then, as soon as another computer joins the network, I get kicked off. This happens with all of my 5 computers. In addition to this, several of my computers will not automatically connect to my network after the computer is restarted. When I try to reconect manually, it says the network is unavailable. The only way I can get back on is if I go into "Control PanelManage Wireless Networks" and delete the setting for my network, then connect again through the "Connect to a network" window.4 of my computers are running Windows Vista with a minimum of Service Pack 1. The Other is running XP with Service Pack 2.
View 9 Replies
View Related
Nov 30, 2011
I'm capped out at 12 mbps service through Mediacom. My PC is directly wired to the WRT120N. I consistently test in the 11 mbps range.
I have a very unusual issue though.
I can connect my iphone and Xbox wirelessly through my router with no issues on their side. However, any time I do so, it kills my wired connection on my PC. I'm not doing huge downloads or P2P or anything like that. In fact, the speed drops immediately on my PC the moment I connect my phone to the wireless network regardless of what i'm doing on the phone (checking email or loading a webpage).
View 2 Replies
View Related
Apr 17, 2012
I have a Linksys WRT120N wireless router that I have had for almost three years now. It recently has started dropping all internet connections very randomly, sometime multiple times in an hour. I will lose my connection to the internet and connection locally to other laptops then it will reconnect. It is also disconnecting when wired as well as I have a playstation using a wired connection out of the router and it loses connection all the time as well. What is causing this, I am pretty sure it is the router and not my internet service.
View 8 Replies
View Related
Jan 23, 2011
I have a WRT120N router .It has something to do with turning on or re-introducing certain wireless devices into the area. When I come home with my iPhone & my wife is on her computer, suddenly the wifi stops. And vice-versa. It's ridiculous. I'm not a computer programmer but if I was I'm pretty sure this would be a no-brainer to fix. Especially if the company that paid me took pride in their products.
View 8 Replies
View Related
Sep 13, 2011
I’ve bought a router, and a wireless antenna for my laptop, since I have a high-speed internet outlet in the living room, but I use my laptop in the kitchen (I don’t have any other pc). So I’ve configured my Linksys WRT120N router in the living room, unplugged the ethernet cable from my laptop, plugged the wireless antenna in the kitchen, and everything was working fine with the wireless network. After about one month I was not able anymore to enter my network with the security key, there was actually no prompt for the security key, just a message “Cannot connect to the network”. I then had to reconfigure the router, going to the router IP address (I used the default settings, a blank for username, and “admin” as a password, as per instructions), use another network name, security key and password, and was able to start again a wireless network with the wireless antenna as before. This problem represented other 3 times (in the last 3 months), and was working fine, but now I cannot reconfigure the router anymore, since the IP address doesn’t accept BLANK/ADMIN anymore, and if I go ahead and reconfigure the router a message says I have to use the default settings in the IP address…
View 2 Replies
View Related
Apr 9, 2012
my router drops connection several times a day. I have to unplug the router every day so that my devices can stay connected. I hate when this happens late at night when i'am upstairs and have to go 2 stairs down to get internet on my devices. For example if i want to connect my iPhone to my Wireless network it gives me an error with: 'No connection can be astablished with this network'.
View 1 Replies
View Related
Apr 25, 2010
I often loose internet connection recently while online. I always check my status on 192.168.1.1 when this happen to see if i'm getting 0's ISP but it does not say that.I also tried ipconfig/release and renew I also tried right click wireless icon and click "repair"Power cycle always worked for me in the past but today to my dissappointment it did not.after power cycling I check my status on 192.168.1.1 and now it indicates 0's.
View 9 Replies
View Related
Apr 18, 2010
I have a disconnecting problem with my WRT120N (Linksys) wireless router. Sometimes all wireless devices lose the connection to the internet, and the access to the router administration page (192.168.1.1) becomes impossible. In this case LEDs of power, internet and wireless are lighting without flashing. This problem usually occurs every 48 hour, and there was no way to make a reconnection except turning the router off by unplugging the power wire and plug it again…
I hope find a solution for this problem here
Other question: are there any problems in Firmware Version: v1.0.04
Note: currently I use Firmware Version: v1.0.01
View 9 Replies
View Related
Feb 4, 2012
- I am losing internet connections at least 1 time/ day. I have 2 wired and 2 wireless devices.
- when the internet is down I am connected to the router (wireless and wired, the connection is not lost/cable unplugged..).
- only when I power cycle the router I recover access to my admin page and internet connection.
* Firmware Version 1.0.06
View 5 Replies
View Related
Dec 3, 2011
I recently upgraded my Linksys wrt120n router firmware & had to reconfigure settings. Subsequently, some (but not all) of my apple devices are having intermittent wireless connection problems. Specifically, my ipad1 & ipad2 never lose their connection but a mac book pro (~ 2 years old), iPhone 3g, iPhone 4, older iPod touch & very old i book g4 all work for a period of time (usually 1/2 day) & then lose their connection. When I attempt to reconnect these devices I receive the following error..."unable to join the network xxxxxx....". I also have a Dell laptop (1 1/2 yrs old) that generally does not have the connection problem. Finally, when the devices do lose their network connection all I have to do to reconnect is go to the Linkys router setup webpage & click on save & the wireless connection works again (almost like this is just refreshing the connection for these specific apple devices). I was not having any problem prior to the firmware upgrade & from what I have read the older firmware version is no longer available so going back to the old firmware does not appear to be an option.
View 1 Replies
View Related
Dec 26, 2011
Router config and i just follow the instructions anyway i just bought this router cuz the old one failed and it was installed ok with internet connection and everything but when i open a program like bittorrent azureus the internet connection dies, it happens on my laptop and mac they both seem ok but when i open that program internet connection disappears
View 1 Replies
View Related
Jul 10, 2012
Reciently I bought a WRT120N Router to get a better internet connection and to have more capacity to connect different wireless devices, because the modem from my internet provider company is extremely restrictive.
I use an iMac, a Notebook with Windows 7 and a Netbook with Ubuntu 11.04, besides different devices (iPhone, iPod, PS3, Kindle). Although when I configured the router I connected every devices simultaneasly, with better signal quality than before, after using it for a couple of days I found that it disconnects itself, I can't access internet, and my only solution it's to switch it off and on.
View 1 Replies
View Related
Oct 14, 2011
After an upgrade of the WRT120N to firmware Ver.1.0.06 (Build 01) every device I have tried to use WPA authentication with will authenticate / associate with the device then drop the connection just prior to recieving a DHCP address.I have tried a Dell latitude laptop with the broadcom chipset, an iPhone 3GS as well as an motorola with google pad device and all experience the same problems.I have removed all mac address filtering, and re-enabled the essid broadcasting only to have the same problem persist despite stripping everything down to just WPA.
View 2 Replies
View Related
Aug 9, 2011
I'm running Windows 7 64bit and I have sucessfully configured my wireless print server (Linksys WPSM54G) to work with my computer and our HP DesignJet 500ps. I have been able to print several sets of drawings without issue, however if the plotter is inactive for an extended period of time (1 hour +/-) the wireless print server loses connection with our router. At the same time the print server loses connection, an associate in our office with a wireless connection to his computer also loses connection to the router. A simple power cycle of the router and print server restores the wireless connection
I chatted with Linksys online tech support and they confirmed that I had the most recent firmware in both the router and print server and had me reconfigure some of the wireless settings on the router. All was good until about an hour ago when I tried to plot and discovered that the print server had lost it's connection to the router and my associate had also lost his wireless connection.
What's the deal here? I feel as though the root cause of this issue is related to the wireless router rather than the print server as my associate was periodically losing connectivity to the wireless router before installing the print server.
View 3 Replies
View Related
Feb 16, 2012
I replaced a WRT54G2 V1 with a E1550 earlier this week. This router connects a sub-net of our office to the main network of our office. When the WRT54 was in place everything worked without a hitch, but the E1550 keeps dropping us from a server we have on the main network. The WRT54 is back in play until I can figure this out.
View 1 Replies
View Related
Dec 8, 2011
I purchased an E2500 router today and it worked perfectly for about 4 hours. Now it drops my internet connection constantly. I can connect and load maybe 2 pages before that little yellow triangle of doom appears. Then after 2 or 3 minutes I am good and can reconnect. This cycle just keeps happening.
View 1 Replies
View Related
Oct 7, 2012
Currently running Windows 7, with internet explorer. I have most recent firmware installed on my e2500. The unit drops wireless connectivity on an intermittent basis. Sometimes after 5 minutes and sometimes after 20 or 30 minutes.
View 9 Replies
View Related
Nov 14, 2011
I'm running Windows 7 Home Premium (64 bit) connected to a Linksys WRT610N Router. I have attached a 320GB USB 5400 rpm hard drive to the router as NAS storage.The router is running 2.00.01 build 15 firmware. I get frequent drop-outs when transferring large files. Tonight I've been trying to transfer a 4.36GB file to the drive from my PC. I've tried several times. At exactly the same time, with about 377MB to transfer I get a message saying 'There is a problem accessing Z: make sure you are connected to the network and try again'.
View 1 Replies
View Related
Oct 1, 2011
I had the 2 Wire Box that received TV and internet. Called my ISP and they gave me this access point to use instead. I hooked it up and it was fine for about 2 weeks. Suddenly for no reason it started dropping. Noticed it first when online gaming on my PS3. Checked laptop and all wireless devices down. Takes about 30 seconds.
View 1 Replies
View Related
Aug 1, 2012
Wired connection to the router works fine. But it drops all the wireless devices (PC, phone, tablet) multiple times each day, sometimes only 30-60 minutes after reconnecting. Power cycling the router "fixes" the router and allows reconnection. There are 2 topics in the FAQ section that looked good: Getting poor or no signal from a wireless routerTop causes of dropping wireless connection on a Linksys routerbut clicking on those does not bring up anything.
View 9 Replies
View Related
Feb 4, 2012
Set up: Router: WRT110 1 computer connected via ethernet cable 1 computer using a wireless nic card from cisco
The problem is thus: if the first computer is actively using the internet (even activities as mundane as browsing one's email) the computer connected wirelessly will lose its connection to the internet yet maintain its connection to the router. Both can be actively using the internet, but the wireless will seemingly at random drop internet access (usually in 30-120 minute intervals).
The computer connected via the ethernet cable was unplugged for a week and during that time the wirelessly connected computer was used extensively and did not lose connection once.
I don't understand how to even frame this problem in a concise manner, much less seek information as to how to resolve it. It's seemingly giving all priority to the computer connected via ethernet but I that's just intution speaking.
View 4 Replies
View Related
Oct 3, 2011
I recently changed the security mode on my router from WEP to WPA2 Personal. However, since that change, I've noticed that the wireless devices, 2-laptops, are intermittently loosing their connections. . I don't know if it has anything to do with the security mode change, but I don't want to go back to WEP for obvious reasons.
View 9 Replies
View Related
Nov 15, 2011
I bought a e4200 router about 3 weeks ago and after a power outage it decided it didnt like being connected to the internet anymore. So i got on the phone with cisco they determined the router was no good, mind you my laptop would connect wired. So they sent me a "refurbished" one, so i set it up. The new setup was wonky because it said the same message "Your connected to your router but..." then after trying to get the connection its self and failing it came up with "congratulations you are now connected to the internet". That lasted 3hrs and 45mins then died, so i went upstairs to power cycle it, it decided to connect with the old settings. That lased 25mins then died, so i reset it and reconfigured the router. Wouldnt connect, i checked my mac address and it was using my wireless one and kept turning on my wireless connection durring the install. So i cloned my wired mac address and got the internet for roughly an hour... then it died. So i reset it again and kept the wifi off got it going and decided to go to sleep. I wake up and its still working after 8hrs, i go down stairs with my tablet and i dies again. This time it refuses to reconnect, refuses to reset back up just doesnt want to work.
View 3 Replies
View Related
Feb 4, 2011
I just got an E4200 and have a SBG6580 cable modem. I cant seem to set this up properly and my connection keeps dropping. What is the proper set up ? I would like to configure it so the cable modem handles the DNS and the E4200 handles the wireless.
View 4 Replies
View Related
