Linksys Wireless Router :: Samsung BD-C7900 Won't Connect With E4200v2
Feb 15, 2012
So now I have a good connection with my secondary router going to my acer a500 android tablet, my laptop, and panasonic viera tv. All is good thus far. However, I cannot connect my Samsun BD-C7900 Blu Ray. What is really wierd is that the 5 Ghz and 2.4 Ghz have two different names on my router (cause that is what the cisco support tech told me to do- give them separate names) but on the Samsung BD-C7900 - it shows that there are two signals coming in but with the same name! When i tried to connect i get an error message. Keep in mind my E4200 v2 is secondary router connected to fios actiontec.
View 1 Replies
ADVERTISEMENT
Feb 24, 2013
I've had this E4200v2 for a while now, and it's been giving me a headache because even at default wireless setting with the passphrase, it literally won't ever connect from a linksys wireless adapter using the mixed WPA2 Personal or the 'EasyConnect' button feature or the PIN, with both side's fireware updated to the latest. There is no issue connecting to the router as long as the security is off. I've tried other form of encryption to no luck.
View 1 Replies
View Related
Jan 20, 2012
I have an E4200v2 configured with an n-only 5GHz network and a mixed 2.4GHz network. Our MacBooks and iPad connect to the 5GHz network, and everything else (iPhones, TVs, etc) connect to the 2.4GHz network. If I disable "WMM" on the QoS screen, nothing can connect to the 5GHz network. Those same devices can connect to the 2.4GHz network, but not the 5GHz. The MacBooks, for example, get a connection timeout error, and the iPad just says "cannot connect." This doesn't seem quite right. I don't absolutely need to disable WMM, but I wanted to make sure that normal WiFi Internet traffic didn't get priority over local wired Mac->AppleTV streaming or voice calls from our wired Vonage box.
View 2 Replies
View Related
Mar 3, 2012
I recently puchased a new E4200v2 router and one of the devices that I have on my network is a Level1 WCS-2040 wireless network camera. My old router was a Netgear WPN-824. I was able to (and I'm still able to) connect the camera to the Netgear router with WPA-PSK but not to the new E4200v2. The only way for me to connect it to the new router is with WEP, which I obviously do not want.
I'm at a loss for what the problem is because the setup is easily done. I'm thinking it's an issue with the E4200v2 but I'm not sure what... hoping that the issue could be resolved in the next revision of the firmware. I've tried WPA2/WPA Mixed Mode, WPA Personal (which I understand is the same thing as WPA-PSK) and WEP. The camera supports WEP and WPA-PSK. When I have the camera configured with WPA-PSK it simply isn't connecting to the E4200v2, only the old netgear.
See screenshots below:
Netgear router wireless config:
Netgear router connected devices (shows laptop and wirelss camera):
IP Camera config while connected to old router:
IP Camera working on old network:
E4200v2 wireless status:
IP Camera config while connected to E4200v2 router (via wired connection, not wireless):
When the wired connection is removed from the camera and powercycled, the E4200v2 does not list the camera as a connected device. I've power cycled everything, multiple times and tried everything I know of. What could be the problem? Note that the MAC address for the camera is the same for both wired and wireless adapters. And no, Password1 is not my default password... just what I was testing with for the purpose of screenshots.
View 9 Replies
View Related
Sep 21, 2011
When I try to connect the galaxy to the wireless network, the tablet shuts down (to the start page, unlock page) when it is searching for the ip address for the network. The firmware is 1.55.02. Cannot get upgrade as not available from Cisco. Have disconnected all other devices from the network in case there is some interference problem.
View 1 Replies
View Related
Mar 26, 2013
I've Linksys EA6500 router and tried to connect my Smart TV (Samsung UE-40EH5307) via cable.DHCP server is turned on
1. TV can't get IP address
2. When I entered IP, Gateway, DNS manualy in my TV it connects to router but not to internet.
3. When I switch cable to my laptop it registered and get dynamic IP without any problem.
4. I've insert WIFI adapter into TV and it connected and got dynamic IP without any problem.
View 9 Replies
View Related
Feb 11, 2011
Trying to connect a Samsung clp-315w wirelessly to my E3000. I plug the Ethernet cable into both to configure the printer and I cannot access the printer via its IP address. I suspect the printer is reporting the wrong IP address or it the IP is not being assigned by the router or it is being blocked by the router. Routers firewall is off. I use the Samsung software and it does not see the printer either. It seems the router is not seeing the printer or allowing it access to the network. Spent much time with a good Samsung support person and tried everything and narrowed the problem down to the router connection. Is there a setting on the router which needs to be changed to allow me to see the printer to configure it for wireless access?
View 6 Replies
View Related
Mar 18, 2012
I have a E4200v2 and im getting wireless connection issues. I have updated to the lastest firmware and have checked all my wireless settings. I dont use usb storeage. I have 1 laptop using 5G, my iphone using 2G and my wife mac using also 2G.. the problem is that, once we stop using the 2G connection (leave it overnight), it just dies the next day.. it wont connect, i double check the password and it wont connect. But the 5G connection is fine.. Do i have a break E4200v2? or anyway of fixing this?
View 2 Replies
View Related
Dec 27, 2012
I purchased an Samsung UE46ES6300 Smart TV for my Boyfried for Christmas & we are struggling to connect it to our WiFi to use the features. Obviously I went through the procedures - Network settings, found my WiFi, typed in my Network password & unfortunately states: 'Unable to connect to the Wireless Router'. Taking into account my Virgin Media Router is directly next to my TV? The Wireless & Internet is 100% working as we have other devices running of it - I-pad, Laptop, Phones etc!
View 9 Replies
View Related
Jun 29, 2012
I think my E4200v2(Firmware Version: 2.0.37 ) should redirect to CCC as this link, is the CCC just could be used in US?
View 4 Replies
View Related
Mar 16, 2012
Recieved this E4200 as a repplacement for a v1 that kept dropping wireless connection. Now after about 1.5 months the router keeps rebooting. Tried resetting, etc...no luck. Calling Cisco now.
View 3 Replies
View Related
Mar 28, 2012
this topic has been discussed under the v1 software and marked as solved yet it has not been. Has anyone attempted with version 2 software and been able to connect after the arp was flushed?
View 6 Replies
View Related
Apr 21, 2012
Just got my new E4200 v2 router. Set up mac filtering for one device and after saving the change the router was refreshing and disconnected all my devices and could not log in to the router wired or wirelessly and had to do a factory reset. Have the latest firmware. Is this a defect in the router?
View 2 Replies
View Related
Dec 23, 2011
I will soon upgrade my wireless network from a WRT610N to an E4200v2. At setup of the router, I assume I'll be able to change the SSID of the E4200v2 and I plan to keep the same SSID as on my old router. With the same SSID as currently seen by the devices on my network
View 4 Replies
View Related
Jun 29, 2012
I have a synology DS411 and a ATV2.DS411 is always downloading from internet,normally the download' bandwidth of DS411 is around 2MB/s.In my old netgear 3800,i just need to active WMM and add a port OQS that the port connection DS411 is low.Then when I watch stream video from internet on my ATV2.I can see the DS411's bandwidth will be reduced automatic.I replaced 3800 with E4200v2 some days before,and I have done the same config ,turn WMM ,set ATV MAC to highest and DS411 MAC to lowest. But when I watch ATV2,DS411's bandwidth seems not be reduced,so I cant get the smooth video Its very bad.
View 9 Replies
View Related
Feb 29, 2012
We have the Linksys E4200v2 router. We have two servers on our network that we want to access remotely (from outside). We have two Static IPs from our ISP. We currently utilize one of those IPs to access one of the servers-no problem. How can we utilize the second IP to access the second server?
View 3 Replies
View Related
Jan 11, 2013
I have a static IP on the ATA (Linksys PAP-2T) ...the router will only pick it up occasionally...most times it does not. The ATA is on and working (I can call in/out) but I can't see how the router can't find/see it. I have added the ATA to the DHCP reseve list but still nothing. I have the port fowarded for the ATA but when I go to canyouseeme.org it comes up as "Connection timed out"...becuase I think it can't see the ATA behind the Router.
View 1 Replies
View Related
Jan 8, 2012
On the D-Link it was easy, I can see who is connected to which radio.But I can't figure out how to see who is connected to WiFi on hte E4200?I run several access points in my house, and I need to make sure htey are all working.If I can't see who, if any, is connected, I have no idea if WiFi on the E4200 is working.
View 2 Replies
View Related
Dec 14, 2011
V2.0.26.124551 is now available. I did the online upgrade and it took just a couple of minutes including the reboot. The firmware is not available as a download yet for manual install. This firmware is dated 11/14/11 so it doesn't appear to correct the Port 53 issue reported earlier.Release Date: Nov 14, 2011 Firmware version: v2.0.26 (Build 124551) - Support for the WAN L2TP and PPTP protocols
View 1 Replies
View Related
Dec 20, 2012
My ISP dynamicly assigns IP's so I have my New E4200V2 set up as Automatic Configuration DHCP. I want to be ablt to use a specific DNS server rather than the one issues by my ISP.No matter what values are in the Static DNS 1, 2 and 3 the router continues to pull a DNS from my ISp. My POS old D-link 615 was able to utilize a custom DNS server with no issues so surely ther emyst be a way to do the same on the E4200.
View 8 Replies
View Related
Dec 23, 2011
E4200v2 DMZ does not appear to work correctly?I have two e4200v2 both with latest firmware and it appears to me that the DMZ setting does not work. I continue to have to apply many port forwarding and triggering rules to make needed ports accessible.
View 9 Replies
View Related
Aug 16, 2012
I am wondering what is the optimal way to set-up my E4200v2 and PLWK400 at home? I have several devices (laptops, tablets, phones) that connect on .11g and .11n.
My current set-up:
E4200v2: 5ghz - Wireless-N only (SSID home-n), 2.4ghz - Wireless-B/G only (SSID home-g)
PLWK400: SSID home-ext (separate part of the home)
I am using WPA2 Personal security if that makes a different. One question would it be "better" to have the same SSID for all 3 wireless settings (5ghz, 2.4ghz, and PLWK400)? Would the various devices know which frequency to switch to for best speed and range?
View 6 Replies
View Related
Feb 24, 2013
I tried to upgrade my router firmware to the latest 2.1.39.145204 (downloaded from cisco website) but seems like the upgrade didn't go well. I am unable to open the admin webpage. I can get to the login page on 192.168.1.1, after i enter the admin password the next page doesn't load. It keeps showing 'Waiting' at the center of the page forever.. I have tried to do the 30/30/30 reset to no avail, i tried to do tftp downgrade to older firmware version but the tftp boot doesn't even start. Is there any other way i can either fix the current firmware upgrade or downgrade it to the previous version?
View 9 Replies
View Related
Jan 23, 2012
Where can I download the 2.0.36 firmware?I flashed it through the UI but since the factiry fw is crap I want to try the third party firmware that are available but I want to make sure there is a path back to factory version in case I need to return the product.
View 1 Replies
View Related
Aug 1, 2012
I purchased an e4200v2 to replace my old WRT160n which I have been using for years with no issues. Last night the e4200 crashed on me when I went to reset the router I noticed the CISCO light was blinking very slowly and I had no network connection. I power cycled the router and still no connection so I hit factory reset button. Nothing happened. Did a 30/30/30 reset nothing happened. At this point I have a 34 day old plastic brick on my desk and I'm back to using my old WRT160N. how to unbrick this router?
View 3 Replies
View Related
Jan 31, 2012
No problem setting up the FTP server on the router. It's working perfectly from inside the LAN. But any attempt to access the built-in server from the WAN side is fruitless. I found that if I turn off the IP4 SPI on the router, I can suddenly connect to the built-in ftp server without issue from the Internet. If the SPI option is checked, its a no go.
Is this a bug? I can't imagine that it is intentionally set up such that you have to turn off the firewall in order to use the FTP function externally. At least it isn't mentioned anywhere I can find and it wouldn't seem logical.
View 2 Replies
View Related
Apr 24, 2012
New E4200v2 @ firmware 2.0.36. The FTP server will go offline about once every 24 hours. I can revive it by simply clicking on Save in Storage/Administration or FTP Server. I don't have to change anything, just click Save. How can I keep the FTP running?
"Disk" is a 16gb USB flash memory. Formated FAT32, 1 partition, 6 users besides Admin and Guest, 2 groups besides Admin and Guest.
View 2 Replies
View Related
Jul 24, 2012
My Linksys E4200v2 router died (no blinking lights when a network cable is attached). Is this a bait and switch?
View 2 Replies
View Related
Feb 11, 2012
I recently changed my wirless router from the E4200 to the E4200v2. As far as I know, I have the same settings on the E4200v2 as I did on the E4200. My PS3 will not connect to my wireless network via the E4200v2. I even retyped in my network information (SSID and password) onto the PS3. Still "no joy." Any issue with the E4200v2 and the PS3?
View 9 Replies
View Related
Mar 30, 2012
I have a small issue with Remote Management on my E4200v2.I have enabled it , select https and set Allowed Remote IP Address to any on the default port ( 8080 ).After all of this, I cannot connect to my router from my office or any other place. I'm using DDNS and all its ok ( updated at time ). I've tried also connecting to my direct ip address ( dynamic ) but with no result.P.S. no incoming log from port 443 using https.
View 3 Replies
View Related
Dec 23, 2011
Decided to go with the e4200v2. 199.99 for a router 450 + 450 with a little extra features. very pricey but thought it would be worth it. I got it hooked up with no problems for the first 5 minutes. I have 35mbps down wired from the router and on the 2.4 and 5.0 ghz band about 25 feet from the router was getting just that!! no loss really. However after a few more speed test i noticed it was fluctuating very slow to fast. Also the 2.4ghz was only 144mbps. after getting in the router i changed the 2.4ghz to channel 6 and 5ghz to 153 and changed to 20mhz only on the 2.4 and 40mhz only on the 5.0ghz. Now all is doing well .
1. why am i not able to run the 2.4ghz on 40mhz? when set to auto i have a lot slower speed tests even know it is running on 20mhz only because I'm only getting 144mbps. I don't know why its not running 40mhz ? i don't know why i have to change it to 20mhz only why cant i leave it on auto and if i had a day with little interference it would switch to 40? when left on auto the speeds go down drastically
2. i notice that some channels are brutally slow on both bands. like 1.5mbps ? is this normal
3. is this even worth it if the 2.4 band is acting this way?
4. from insider i see that 5.0ghz only connects to two channels isn't suppose to be 3?
View 4 Replies
View Related
Apr 12, 2012
With other devices, including Cisco Aironet, I've saved a lot of time in the past by cloning the config from one WAP to another. This is for when I have to set up 2 or more WAP's on the same network, that share 98% of the same settings.I was wondering if anyone's ever tried to do this with Linksys devices, and in my case two E4200v2's in bridge-mode (WAP-only). Will it let you Restore a config that came from a different device? (same hardware version of course)Obviously I would change the hostname, devicename & IP address to make them unique. But the rest of the settings would basically stay the same.
I'm talking about E4200's that are being used as bridge-mode access points, and so typical router functions like DHCP server are disabled on both.
View 2 Replies
View Related
May 2, 2012
Have the E4200v2 router. Suddenly my wireless devices have slowed to a crawl. I mean slow. My Cisco Connect confirms that my wired download speed is 30-32 GB, but my two Android devices have slowed to ~500k. I might have changed something - just don't know. I know I'm desperate though.
View 1 Replies
View Related
