I ran a cat5 from my house which has the dsl modem to my workshop; about 120ft.I can plug that cable into my pc and get internet. But if I plug the cable into the Linksys, and the a cable from the Linksys to the pc, no internet connection. How to configure the Linksys so that I can connect it to my PC? I also want to connect my Verizon wireless Network extender to the Linksys.T
View 2 RepliesI've had a problem about the wireless router. I can easily connect to it, but the problem is it doesn't have an internet access even if I reconnect it to the ADSL Modem/Router. I can have access through the internet with the ADSL Modem/Router directly connected to my Aspire one laptop.
Wireless Router:W-G LINKSYS WRT54 ADSL Modem/ROUTER:PROLiNK ADSL2+ Modem/Router
I have Network Magic Essentials and use a Linksys WRT54GS router. I just received a Cisco Linksys 2500 and assumed that it would be a breeze to set-up in place of the WRT54, so that I could gain faster internet and improved range. After about six hours of frustration trying to set it up, I am pulling my hair out! I live in a remote area near a lake, and our only option here is a
Wi-Fi signal beamed to our homes via an antenna, coax cable to a "radio" ( Alvarion BreezeAccess). This has always worked very well with the WRT54, but with with the Cisco 2500, I can get on my local network just fine, but I cannot get connected to the internet. I can disconnect the 2500, and reconnect the WRT54, and get right back on the internet.
Ok, my roomate is hogging the bandwidth on our shared router downloading junk. I'm not sure if he's using a torrent, but just in case he is here is my question:How do I turn off the ports for torrenting on my qwest pk5000 modem? Is there anything else I can do that would work as well?My friend reccommended I turn off every port after 9000 or something.
View 3 Replies View RelatedI'm currently connected to an ISP whose modem is equipped with a wireless router. The router works fine, however, its range is too short. I tried configuring my Cisco Linksys WRT120NL to the modem and the internet does not go to my computer.
View 2 Replies View RelatedI have an old Speedstream 5100 modem hooked to my e2500 router. Everything works well except if for some reason my modem disconnects from ISP I can not log into it through the route to reconnect it. I must plug a direct cable into modem from computer run connect script then plug modem back into router all is fine again.
why connecting to modem through router is blocked?
I can think of from different cables, factory settings, etc. Can't connect to modem straight from computer for some reason, but my old linksys wrt54g still works. I can connect to the router wirelessly and access settings fine. When i try to use cisco connect, the install stops at 25%
View 7 Replies View RelatedI just moved into a new place with a DSL modem and am using the connection from the old tenant until my internet gets set up a while from now. I can plug the ethernet straight from the modem into either my laptop or desktop, and it works perfectly fine. But when I plug into my LinkSys 2500 router, it can't connect. I've tried rebooting the router, the router and the modem, plugging the modem back in first, plugging the router back in first. Nothing. But all I have to do is pull the ethernet cable from the internet port and click it into my laptop, and voila! internet. My name isn't on the account so I can't call the ISP and see if there are any special connection instructions, but I suspect there aren't any based on just being able to plug a computer straight into it.
View 4 Replies View RelatedI currently have a N750 router running alongside a Motorola Surfboard DOCSIS modem from Charter Communications. To the extent of my knowledge, the router had lost its connection and self-restarted, if not a high ping spike, and I could no longer connect to 198.168.1.1 in my web browser, Google Chrome (also, I cannot connect to my modem through 198.168.1.100, it says that the webpage is not available). [code]
View 9 Replies View Relatedhow to i connect mu linksys router to my ubee cable modem
View 2 Replies View RelatedI have a Netgear WNDR3700v2 that I was very happy with until I got a nest thermostat. Apparently it is an unsupported router and I had to change it. I bought a E2700 since it was supported, but I'm having a huge dilemma...
If I connect the linksys directly to the modem, I'm not getting an internet connection. I've released and renewed IPs to no avail..
but if I hardwire the linksys to the netgear, I do get a good solid internet connection. problem is, I have no need for 2 routers setup on top of each other.
basically, I dont understand why linksys is not able to connect directly to the modem. yet it gets solid connection hardwired through another router.
I'm using Comcast and in south FL. it's a motorola surfboard modem
Purchased today 26th March 2012, used CD first as warned, followed procedures, will not connect to WAG 160N modem router. WAG160N has MAC restrictions but MAC of WRT160N added, both in wireless and as a computer. Still won´t connect, gets to 85% in wireless connect mode then fails, gets to stage 4 of router recognition and fails, saying check cables. Cables changed to know working ones, still no success. Tried pinging 192.168.1.1 direct from computer with no success, no access to router log-in page at all. WAG 160N has no problems.
View 2 Replies View Relatedi brought a new wrt120n from the retailer and when i tried to connect the modem and configure, my phone gets dead and i couldnt connect it to the internet.
View 1 Replies View RelatedI have an EA3500, I have 30 Mbps download when I connect my pc directly to the modem. When I add in the EA3500 router it drops to only 10 Mbps download on both wired and wireless devices.
View 9 Replies View RelatedI recently changed my internet connection to DSL from Cable, so now I'm using PPPoE type of connection.
Right now my router is configured as Automatic DHCP with the modem doing the PPPoE connection. All is fine and well.
Since I own a PS3, and Nat Type 3 conection is really bad for my online gaming, I would like to bridge my modem and connect to the internet through my router. That way I can properly forward my ports, use QoS and effectively get a better connection on the PS3.
I was able to successfully bridge the modem, but the PPPoE config on the router isn't able to connect to the internet.
Modem and router have been reinitialized after the configurations were changed. I do have the username and passwords, and they were properly put on the router.
Upgraded my E3000 from 1.0.02 to 1.0.04 and now I cant get an ip from my arris modem. I did the 30/30/30 reset and everything but no luck. I've had to plug the modem directly into the computer for now. Where can I find the 1.0.02 download or how can I fix this?
View 3 Replies View RelatedI have rather huge connection at home. DL speed 80Mb, UL speed 3Mb.When I connect my PC directly to modem and configure PPPoE connection, I get 81Mbits/sec. When I connect my old ASMAX $30 router, I get 78 Mbit/sek. And I find it OK.But when I connect my EA6500 I get 28 MBits/sec. Same result on wire as on wireless connection. Of course If I enable prioritisation, I get even less, 12-15 Mbits/sec.I tried already even configuration with ASMAX as wired router and EA6500 connected to its LAN port. It gives me 50Mbits/sec.
View 5 Replies View RelatedMy Motorola SBG901 Modem/Router combo has stopped connecting to the internet. I have done all the troubleshooting with Comcast and with Motorola and it is out of warranty, so I will have to purchase a new one.In the mean time, I wanted to use it only as a wireless router connected to my Scientific Atlanta DPC2100R2 modem. Is there anyway to do this? Is there a way to disable the modem in the SBG901? Simply connecting with the ethernet cords has not worked. I connected the DPC2100 to the SBG901 via ethernet cord. My computer was able to pick up a wireless connection but there is no cable connection.
View 1 Replies View RelatedIn order to get my wireless printer up and running I need to temporarily disable my actiontec PK5000 router.
View 11 Replies View RelatedI just got internet and cable at my apartment the other day. My roommate and I got Cox Cable and my roommate had a used Linksys router to connect to the modem. I'm not sure how the Linksys was set up (I'll get that information soon), but the internet worked for her without her having to connect her laptop to the router. When I tried to use the wifi, I was never able to connect properly. It would say that I was connected to the router, but that I wasn't able to use the internet. Then I tried to connect the laptop to the Linksys router with a ethernet cable and the internet worked. Also, after I unplug the ethernet I am able to use the internet, but the connection goes out every so often. I also wanted to use my PS3 with the wifi, but at this point I doubt it will work unless I find some solution. As for specs, the Linksys is a Model # BEFW11S4 ver. 4. Oh, and now my roommate is having the same problems now.[CODE]
View 4 Replies View RelatedI was trying to work with a friend set up his wireless router. He had the Geeksquad come and set it up and I have no idea what they did. A mess of wires. I noticed that I was able to log into the imbeded browser of the modem and the router from the main PC. I didn't think it was possible to log into the modem if it was set up in bridged ethernet mode. His internet is working but I was thinking that he may have problems with double NATing.Basically, I just want to know what options there are for setting up a router to a modem. I'm aware of bridged mode and setting up the router as a switch (not real knowledgable of this one). Seems like DHCP is enabled on both devices.
View 3 Replies View RelatedAfter reading posts in this forum and others, and reviewing MSFT tech docs, I'm still not able to establish file sharing between the wired PC and the wireless-connected laptop. Maybe I'm working under some stupid assumptions. I am able to ping each computer by their IP address - I can ping the laptop from the desktop, and vice versa. The desktop shows the Basecomputer under network places, but on the laptop, nothing at all shows up under network places. Laptop missing something?
The details:
a) Connecting to internet via DSL, Qwest ISP, Actiontec PK5000 Advanced Networking Network Router. Advanced Networking router, to me, means that home networking shouldn't require any other hardware. Stupid assumption?
b) Desktop PC is connected to the modem/router via ethernet cable
c) Laptop is connected to the modem/router via wireless, (Dell Wireless WLAN 1350 WLAN Mini PCI Card). Assocation tab of the wireless properties gives the network authentication/data encryption types as Open/WEP.
d) Some settings of the modem, viewed via the browser (192.168.0.x)
- Wireless security type: WPA
- MAC authentication Enabled
- Firewall security level: Off (NAT only)
e) Desktop PC is Windows XP Home Edition, SP 3
f) Laptop is Windows XP Professional Version 2002, SP3
g) Both are running Windows Firewall; File and Printer Sharing is checked for both, under the Exceptions tabl
h) I ran the Network setup wizard for both, using same Workgroup name, called HOME. Desktop is called BASECOMPUTER, and Laptop is called LAPTOP. No errors in the setup. On the desktop PC, under Windows Explorer, Network Places -> Entire Network, I can see a 'Home' network under a Microsoft Windows Network icon, with the Basecomputer listed. However, LAPTOP is not listed. This is after a couple of restarts.
i) ipconfig and nbtstat ouput
From the desktop:
Windows IP Configuration
code...
Internet went out for 3 days straight and calling frontier about 20 times they finally gave us a new model 7500 modem to replace the previous. The linksys e1200 router which had worked perfectly fine before the new modem has decided to not allow me to connect online. Sometimes it says im connected to internet but web browser does not connect, sometimes it says no internet access. I have no idea what i am doing so im not sure if it is a modem or router issue. I have done full reboots of both and powered on correctly. plugging in the modem into ports 1-3 do not light up the modems ports lights, only port 4 seems to light up when plugged in however computers light up all the ports when hard wired to E1 - E4.i also downloaded the latest firmware update for the linksys e1200 router.All fire walls are shut off and no WEP ( we live in middle of nowhere so a key is not needed )
View 7 Replies View RelatedConnect WAG160Nv2 with another modem / router Wi-Fi?
View 2 Replies View RelatedI am attempting to install the router but cannot connect to SKY ISP. I can connect my laptop to the router both wirelessly and by cable.
View 5 Replies View RelatedI'm starting this thread because I can't get my new Linksys AE2500 wireless use adapter to connect to my new Linksys X2000 ADSL modem. I purchased both of these devices because my old 2wire modem kept dropping the wifi signal and I had to keep turning off and on the modem in order to get the wifi signal back. Now my problem is that I can't connect my AE2500 adapter to the x2000 modem at all, heck I can't connect any wifi enabled device to the modem even though the SSID and password is correct. The adapter finds the network but it can't connect to it at all. The x2000 modem works perfectly since I can use the internet if I connect my computer to it via Ethernet cable but unfortunately I have my desktop in my room and the modem is in the living room so connecting using an Ethernet cable really isn't an option. I tried using my old 2wire modem to see if it would connect to that modem and it did as a matter of fact and the speeds were good but as of late, the speeds have been horrible and the signal drops every few minutes. I get 1 bar in the network status and speed of 1.0 Mbps. Here is a picture for reference:
The problem only persists when using wifi though because when connected to the 2wire modem, the speeds are fast. Range isn't really a problem because im like 10 feet away from the router so I'm not sure what's causing that problem. I assume it's the modem being that its about 7 years old so I would really like to get my x2000 working to see if it's better than my old 2 wire. I'm currently connected to my old 2wire modem via my AE2500 wireless usb adapter as that's the only way I can use the internet.Here's my info:
[code]....
How can I get my dell aximx51v to wireless connect to my 802.11n linksys modem?
View 1 Replies View RelatedI have a cable modem installed to my property but want to use my modem/router to go wireless. The proble is my cable modem output is a RJ45 and the router input is RJ11.
View 10 Replies View RelatedWhen I attempt to connect my new laptop to it and enter the security key/password, it does not accept it.I was able to connect the computer I had before to the router.How can I connect my new computer?
View 9 Replies View RelatedI have a cable line internet connection on my desktop.i want to share this connection to my mobile and laptop through wireless router.my question is which is the best router for this purpose netgear n 150 or belkin n 150 ?do i need a modem to be connected with router?
View 1 Replies View Relatedtrying to set up my router from the qwest modem
View 1 Replies View RelatedHave lost the instructions on how to connect my TRENDnet wireless router to my att DSL modem, not sure if I have all the cords that I need.
View 1 Replies View RelatedCan a Cisco / Linksys EA4500 connect wired to a PK5000?
View 1 Replies View Related