Managing Browser Permissions On Network
Sep 23, 2011
I have been trying to convince my bosses, the IT department, and others where I work, in a small call center, to switch to a different browser other than IE. The reason is IE times out on the techs a lot and freezes up constantly. I am able to use Firefox and Chrome at the lead station and do not have any issues, but the only browser currently allowed on the techs computers is IE. The reason I am getting as to why this is not possible is that with IE, IT is able to block certain options in IE from being changed such as proxy settings, add-ons, and advanced settings, but that these settings cannot be blocked or managed in firefox and chrome.
View 4 Replies
ADVERTISEMENT
Jun 1, 2011
I have a small lan of around 10 computers in my office which are connected through a switch connected to a airtel broadband connection. I want to configure a network server so that I could manage an control the internet traffic used by all the workstations in the lan through that server. All the workstations have either WinXP or Windows 7 on it. I haven't purchased a server. I want to use a desktop(having some good configuration) as my network server.
View 6 Replies
View Related
Jul 13, 2011
I have a network hard drive (NAS) in my LAN. I would like that a few computers in the LAN were able to only read but not write and the other computers could both write and read. Is there any way I could do this?
View 2 Replies
View Related
Apr 17, 2013
I have a department network share that has several sub folders within that share. The director of this department doesn't want her employees to have access to everything in said share. We have a blanket security group for the dept that grants read/write access to the share. I tried creating a limited view security group and added it to the permissions on the share (right click the share, security permissions etc) but I am still able to go into folders that I shouldn't have access to.
View 3 Replies
View Related
Jan 19, 2012
I can no longer add user permissions to a network C: drive - I get an access denied message. What could have happened?
View 6 Replies
View Related
Aug 13, 2012
I've got the E2000 at home for our private network.
We are three guys sharing a flat. We have personal laptops, work laptops, mobile phones, games consoles, tablets etc that connect to the internet.
Problem is that when someone downloads stuff, the speed is slow for the rest of us. So i was hoping i could set up something like three "channels" so each of us could have the same download speed, ie 1 mbs each regardless if others are using the network at the same time. And then maybe a guest network for all the mobiles and tablets etc. MAC filtering for access for our personal laptops should work.
We have a 20mbit cable network line.
Can i do all of this on the E2000 and how?
View 5 Replies
View Related
Aug 17, 2011
The wireless in our condo requires a user and password to be submitted via a browser to connect to the network. My bluray player does not give this option or have the ability. Is there a way to accomplish this? Is there a bridge or router that can make the authentication to the wireless in the building that I could then connect the blu ray to?
View 10 Replies
View Related
May 25, 2011
I have been using this wireless internet connection for a long time, but the other day I went to go online, it didn't work. Ive tried lots of things but nothing seems to work.I'm able to acess the same wifi from my phone and it works fine, so i know its not the actual network, its something on my side.pics of xirrus screenshot & intel proset config attached[CODE]
View 11 Replies
View Related
May 9, 2011
About a week ago my mom (unknowingly to me) installed a registry "booster" (Uniblue Registry Booster) and as expected, it messed some stuff up. As soon as she finished scanning and it "fixed" all her registry issues, she could no longer load webpages in her browser.PC was running XP at the time of the corruption, none of her system restore points work, and unfortunately her automatic backups had stopped running about 2 months ago without me knowing. She's been planning to switch to Windows 7 soon anyway so after a few days of trying to find a solution and not having any luck I thought "well maybe if we upgrade it will unintentionally fix some files / settings during the install." Going from XP to Windows 7 was no fun task itself, but after many hours of installs I had it upgraded to Vista and then to 7.
View 15 Replies
View Related
Mar 15, 2011
We are getting browser redirects on our Netgear home network. It's happening on 3 computers (2 LAN, 1 wireless) and on a cell phone. Have scanned the computers with AVG, Malwarebytes and Super Antispyware.I have to believe it's in the router
View 1 Replies
View Related
Jan 31, 2013
I am experiencing problems trying to access my routers HTTP-type configuration. I have a Billion 400G router. The address to access the router was always http://10.0.0.2 and that has always worked. A dialog box would appear asking for a username and password. Now it doesn't even reach that screen. It says that the connection timed out. I've tried Firefox/Chrome/IE10. To no avail. My system: Windows 8 build 9500. Also something weird. When I type in this Microsoft thing comes up with IIS 8.
View 2 Replies
View Related
Jun 7, 2011
We have set up 1 computer (from now Computer A) running on windows xp as a "server" with other computers in a MSHOME group (from now Computers B -D). File permissions and sharing was set up to allow all remote users (Computers B-D) read and write access. This is however not always appropriate. Is there a way in which we can share a specific file or folder with Computer C (read and write) but not with Computer B and D?
View 4 Replies
View Related
Nov 12, 2011
Any way to get access to facebook yahoo and gmail on bounded network by admin and also using fortigourd by them.
View 1 Replies
View Related
Feb 7, 2013
I am currently facing a major problem. I am a user of the Smart FTP software and have several files in it.However, the "Sites" folder is showing a blank screen. It shows nothing, when there are supposed to be at least 30 files.
I think I have discovered the cause of this; the "Read" permissions are off. Here is where my problem comes in, when I enable it and select "Apply Changes Recursively", it goes back to the unchecked "Read" permission. It doesn't seem to take into account the fact that I want to enable it.
View 1 Replies
View Related
Mar 18, 2011
I work at a small private school for languages and we have 3 public computers for the students to use for general stuff, internet research, facebook etc etc. Now every week i go to the comps and make sure their running well etc etc but every time there is new stupid things being installed by the students. Anyway, i wanna put a stop to this activity. the computers are not a toy for this lot but a tool and if they need a program for something to come and ask. As it stands the comps are all win 7, and are connected to the network via WIFI. the network is a simple zyxel router. There is another office comp connected to the router running Win XP pro and i also have a spare comp in the office which is unused.
View 3 Replies
View Related
Feb 4, 2011
I have a two computers under the same workgroup.
ComputerA - Windows XP SP3
ComputerB - Windows Vista
I shared a folder on computerA and I am able to access it from computerB. The problem is I want to set permissions for the users of computerB on this folder. Under 'Sharing and Security' -> Permissions, I am unable to change the location. It always shows only computerA. How can I change the location to computerB so that I can set different permissions for users of computerB.
View 4 Replies
View Related
Jan 31, 2011
I have networked two computer with printers attached to each. PC1 is with a brother printer attached PC2 with a HP 1100 attached.In the past I had no difficulty with networking the computers and have access from each computer to each of the printers.
I up graded the computer Susan and I am now having a few problems that I never had before.After I perform the Network Setup Wizard on each of the computers (in many different methods) I am having the following problems.First, every now and then I am getting the following message after double clicking on Entire Network then Microsoft Windows Network:
Entire Network Not enough storage is available to process this command.If I wait a few moments I will get the MSHOME and am allowed to click on that. After this I do see both guy and Susan. If I double click on guy I see items pop up. If I click on Susan I get the following message:
Susan is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.The network path is not found.Of course I can not add the printer from Susan either. Though I have had no problem adding the printer from guy to Susan. And it prints properly.
View 14 Replies
View Related
Sep 26, 2012
We just got a new ASA5510 (straight out of the box). I’m new to the Cisco but feel we followed the directions. We connect to the management port and have our workstation set to get an ip via dhcp. A cat5 is connected to the management port, that goes into a hub (tested to work) and a cat5 is connected from the hub to the workstation (tested to work). Nothing else is connected. The workstation does not get an ip address. (assigns APIPA) Both the 5510 and workstation have been rebooted.The workstation works otherwise. We have also connected both a crossover and straight through cable from the 5510 to the workstation. We have statically assigned an ip of 192.168.1.2 to the workstation and cannot ping the cisco (192.168.1.1).
View 2 Replies
View Related
Jul 31, 2011
The application here is a wind power project, built in two phases, without any effort to coordinate or integrate the two sites during the design phase. All operations activities for both phases are performed by one staff out of a common location. This is a rural area and Internet connectivity is mission critical due to contractual obligation with Electrical Utilities.
The client has a need to reconfigure a network which has grown over time in a layer by layer approach, whereas at every point in time that an additional T-1 or other changes occurred to address a specific need, no thought was ever put into integrating the entire site as a whole. It is at best a dysfunctional solution which somewhat accomplishes thier needs, and at worst, a kludgy, grossly security compromised, and difficult to use infrastructure. There is every kind of equipment one can imagine, each installed by some entity providing needed services on the site, but forced to make uninformed decisions because the client really has no IT department to coordinate with. Over time, every vendor just provided their own switch, router, or maybe figured out how to reconfigure another existing device to also provide the routing or access needed, To say the least, it's a mess.
The client requests a solution which provides a means to accomodate 6 internet connections (4 T-1 lines, and 2 satellite) in a manner which aggregates available bandwith and provides redundancy. The T-1 lines will be the main internet access, with the satellite connections only used if available bandwidth falls below some threshold, say 3Mb. There are many internal networks which need to be routed to and between, in total, about 20 subnets. There are 2 SCADA (Control) networks which have a mandatory requirement of 1Mb each, a VoIP system which does not use any internet connetivity as there are 6 POTS lines dedicated to it, an internal office LAN and a turbine manufacturers site LAN.
The T-1 lines, at 1.5Mb x 4 = 6Mb.
The 2 SCADA networks require a guaranteed 1Mb each, the remaining 4Mb is to be allocated between the office LAN and the turbine manufacturer site LAN. The satellite connection are only to be active in the event bandwidth falls below 3Mb.
There are 2 Cisco 2801 routers on site which could be reutilized if appropriate. Each T-1 has it's own Adtran CSU with Ethernet out. All T-1 lines are /29 IP Blocks. 2 of the T-1 lines are adjacent IP Blocks, for what its worth.
Everything here is open to reconfiguration. The client wants this finally integrated correctly with the ability to address emerging Electrical Utility cybersecurity requirements in the immediate future.
An ideal solution would be fully redundant to eliminate the single point of failure at the edge router. As to whether there needs to be separate edge and interior routers, I just don't know that. I would guess everything could be done with just a pair of redundant routers at the edge, but perhaps it is better to do the interior routing between subnets on a different router(s).
Again, the goal is a well integrated, redundant, and secure solution. My part is mostly complete, with the OSP part of the network finally at 100% after 5 years of stupid and careless misconfigurations and bad fiber splicing (by others).
I'm absolutely covered up in business at Layer 1 & 2 on these sites, as the physical plant and associated network elements are typically very poorly designed, specified, and implemented. The complexity of this job leads me to seek outside advice and ultimately a more qualified Cisco professional than me. I'm experienced enough with Cisco to know when I'm in over my head. I know a diagram would be nice, but at this point I've only got a very detailed diagram which reveals too much site identity information to make public. I'll wait to see a few comments and in the meantime work on removing site identity info so I can post a good diagram for everyone to see.
View 1 Replies
View Related
Aug 12, 2011
I have an interesting SVPN challenge that I'm asking the subject experts here to assist me in solving.A customer in Domain A wants to transmit data to Domain B. The customers have agreed to establishing a secure vpn connection from Domain A to Domain B to transmit real time data. The challenge comes from sending unencrypted data from nodeA to nodeB & nodeC withing an encrypted VPN tunned to node d.The challenge is sending non-encrypted data from NodeA to NodeB where an encrypted VPN session is active. Every time I attempt to configure the interface (AppC) the VPN session is terminated, and the interface can no longer "see" nodeD via IP mapping. An engineer recommended adding a second NIC card to NodeB thereby permitting control of the AppC even when the VPN is up and running.Can I send live non-encrypted data to NodeB data buffer, while AppC sends data to NodeD in a VPN tunnel ?
View 1 Replies
View Related
Jan 5, 2012
I want to create a network with a bunch of routers and switches to be used as a test network for company employees to remotely login and learn networking.I don't want this network to interfere with the rest of the network in any way.I am basically trying to create a stub network or a passive network!!
View 4 Replies
View Related
May 28, 2012
I am trying to manage my Dell switch that is trunked from my Cisco 2950, I have trunked vlan 251 (management vlan) and 252,configs below
Cisco 2950 :-
Current configuration : 4794 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code]....
View 7 Replies
View Related
Jan 8, 2012
Im in the process of trying to setup a home network. Computer A and Computer B are in the same workgroup. Username/password are the same.
Computer A = Windows XP sp3
Computer B = Windows 7 sp1
The two computers can communicate on the network. Can ping back and fourth with ip and computername. Computer B can access from what I can tell the whole C:/ drive from computer A. Doesnt ask for a password or anything like that. Just works the way it should.
However, I cant figure out how to share the C: drive from Computer B with Computer A.
Computer B
Click on C: >> Properties >> Sharing
And this is what i see on the sharing tab
It looks like its shared cause i see the \inteli5c. But when i go onto the other computer I cant access it. This picture doesnt seem to want to work. But that link is the screen that comes up when i try to access the C: from the opposite computer.
View 7 Replies
View Related
Feb 27, 2013
I've downloaded Prime Infrastructure 1.2 eval and wanted to see what it looked from WCS that I am currently using to manage the wireless network and I added the WLC (4404) device but it list the device as "Managed with Warning" and I can't find what the warning is.
View 3 Replies
View Related
Sep 1, 2011
Running Cisco NAC 4.1.6 OOB on the LAN. For some reason in the middle of the night, the snmp trap mac-notification added command appeared on the trunk uplink port of one of our switches.
I don't know exactly when the command was added but at 2am when the backup of the config was taken, it was there. At around 4:30am, the uplink went off-line. Is there anything within NAC that would push a change like that automatically to a switch. We do have NAC Profiler running on the network also.The problem was in a branch office so I only got the information second hand what was on the switch itself. We moved the uplink to a different port which allowed the switch to show up on the CAM again, however when I viewed it, the uplink port was set to controlled!
Does this make any sense?
how long devices will stay in the certified device list if no timer is configured to clear it out?
View 2 Replies
View Related
Mar 25, 2013
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V4.20.0
Firmware Version :
ISP :
I am trying to work out how I can use the WR702 to connect to a Hotel's wireless connection. As with most modern hotel setups, the hotel requires the user to access a web browser and enter the room number and select a purchase plan.I believe there must be a way that I can connect the WR702 to the hotel's network and then use a browser on a linked (wireless or ethernet) laptop to launch the browser and log in, however, I have tried every default configuration on the WR702 and cannot find a solution.
Setup:
WR702 router
HP EliteBook 8440p laptop (ethernet and wifi available)
Hotel wifi (multiple identical SSIDs in the survey but shows as a single wifi name on my iPhone)
View 1 Replies
View Related
Feb 14, 2011
Even though I am an Administrator on the server, sometimes I create files or folder on a network drive and when trying to access them later (or immediately in some cases), I am getting an "Access Denied" box.For example, I just created a folder, moved an item into it, then tried to rename the folder and was denied access.
View 3 Replies
View Related
Nov 26, 2011
I have a desktop and a laptop. I'm trying to share my external HD from my desktop, to my laptop.What I did was gave the local administrators group full share permissions to the drive, and of course the local administrators group also has full NTFS permission.That being said, I went to my laptop and did a Code:net use X: \mydesktopexternal /user:mydesktopuser PasswordExternal is the share name for the external HD on my desktop. The command worked successfully, however, I am still getting Access Denied when trying to get inside of this mapped drive.How and why does the command map the drive properly, using those credentials, but there's no access when trying to navigate to it? It works if I give Everyone full share permission, but I don't want anyone to just connect to it. Use password protection file sharing is enabled, but of course with "Everyone" given permission, that won't apply (at least to my knowledge).
View 7 Replies
View Related
Jun 29, 2012
I started getting into IT (as a job) a little less than a year ago, though I've been working with computers for close to 20. So networking was never something I was into while working on computers at home. I've been handed a significant position at work and I am learning a lot as I go. I want to know how to grant permissions for a domain user to a directory without adding the user to all of the sub-directories and directories. The only way I've figure thus far is to grant permissions to said folder, then inside remove the "inherit permissions..." but then I have to manually remove the permissions to every other sub-folder.I want to add a single path to a folder by adding single permissions to each folder until the directory in question is reached.
View 2 Replies
View Related
Jan 19, 2011
I have two desktops connected to the internet through wired connections to a router. I also have one laptop that is wireless connected to the internet via the same router. (Also have another laptop running Vista, but not using it right now.) and all are part of the same work group with unique computer names.Desktop 1 can see that there is a work group, but cannot see the computers in the work group. Error message about permissions.
View 1 Replies
View Related
Jun 3, 2012
How to share a specific folder via LAN and enable permissions.More specifically, I'd like to share this laptop (Win 7 OS) with my Android PMP and Linux laptop (Mint OS) and grant it "full control" (read and write permissions) without granting "Everyone" control and without adding separate users with pw onto this laptop.(scroll to end of the post to skip details)Let's say the folder that I want to share is called "Bouncy." I right-clicked on "Bouncy", clicked on "Preferences", then enabled " Share.."to "Network Path: \MYCPUNAMEBouncy" and allowed Guest and Homegroup read/write privileges. From my Linux, I "Connected to Server" but couldn't connect.Under "Advanced Sharing" in Windows 7, I clicked "Share this folder" and created a profile under "Share name" => "Share name: Bouncy".I can connect from the Linux, but can't write to the Win 7 folder.
In "Advanced Sharing", under "Permissions for Bouncy", the "Group: Everyone" only has Read permissions. I clicked on "Add" and "Selected the object type: Users, Groups, or Built-in security principles" "From this location: MYCPUNAME". Under "Enter the object names to select" I wasn't quite sure what to write, so I clicked on "Advanced". The search results from "Find names" with these settings yield a ton of names that I'll omit. I first clicked on "MYNAME" in "My Folder": "MYCPUNAME". No access from Linux.I then changed the permissions to "Network", allowed full control permissions and now was able add files from my Linux. Which is good.How do I make it so that only a few specific IP addresses or Users (PMP and Linux laptop) have full control? How do I make it so that a password is required to access from LAN with full control?
View 5 Replies
View Related
Jul 25, 2011
Is it possible to manage Lightweight Access Points in Ciscoworks LMS 4.0?
View 3 Replies
View Related
Apr 17, 2012
Anyone got a single VSM (albiet in HA) managing two vDS split over two ESX clusters connected to a single instance of vCenter?
View 0 Replies
View Related
