Motorola WR850G - Cannot Log Into Router / AP Setup Page
Jan 23, 2012
I have a WiFi setup where the wifi signal can go to 2 houses on my long-range property. One wifi router (Motorola WR850G w/ newest firmware update) is up on a pole between 2 of the houses. I could access it fine via wifi on my PC ever since i set it up a while back, but I was messing with it one day last week (nothing major changed), and all of a sudden now I cannot access the router setup page no matter what! (IP=192.168.10.1 by default).... it just simply times out now and gives me the 30 seconds loop to a page not displayed error in my browser.
I really would like to reset it via wifi, since its up powered on the pole outside, it'd be difficult to get up there and reset it myself. Is there a way I can get access to the page again in any way, by only using wifi from my PC????
The WiFi works great either way, and pinging to the router is 1ms so I just don't get it! Things I've done:
1. Pinged router, pings fine from any PC via WiFi...
2. Changed PC from DHCP, to 192.168.10.8 to get a non-used IP, since maybe it was timing out to the 192.168.10.7 IP I was using via DHCP. No go, it still times out no matter which PC or IP I have!
View 5 Replies
ADVERTISEMENT
Feb 27, 2013
My Motorola 850G router is several years old and working fine. However, my wi-fi connection is presently "unsecured" and I need some assistance as to how to go about setting up a secure network. My browser is not recognizing the router's default IP address.
View 1 Replies
View Related
Feb 21, 2012
I have a Motorola SBG901 router. Typing ipconfig showed that 172.18.8.1 is the Default Gateway and this is the URL I always used to access the router login page.
I reset the router today by holding the reset button. Now typing the URL 172.18.8.1 does not work. The router user guide says to go to 192.168.0.1. I have tried this but it also does not work. For both I just get the "problem loading page" in Firefox.
The Internet works fine both with an ethernet connection and wirelessly. My only issue is that I cannot access the Motorola router login page. I could access it fine this morning before I reset the router.
View 6 Replies
View Related
Jul 28, 2011
i need to get into the web page because i need to open my XBL nat and when i type in the password to get into the routers page i get a blank screen
View 2 Replies
View Related
Dec 27, 2011
I am trying to get my parents Kindle Fire to work. They recently purchased a Motorola Modem/Router which is hooked into the desktop and works fine. I want to get their new kindle to work and can not seem to figure it out. Their operating system is Vista which I can upgrade to Windows 7 if that would make it easier. When I click on setup the WiFi part of the installation wizard cd that came with the Motorola it says there is not a network adapter. I know what that is however I do not know why I would need it when the desktop is hooked directly into modem/router and I just need the WiFi for Kindle.
View 12 Replies
View Related
Jun 10, 2011
I recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
View 2 Replies
View Related
Mar 22, 2011
i need to do the following:
-go to routers startup page
-log in
-look for my WAN MAC address
it seems so easy, but i keep getting instruction to do things like type in different numbers into my browser which never work.
View 14 Replies
View Related
Apr 21, 2012
I can't connect to my setup page [url]... I get to the page that says..."There is a problem with this website's security certificate." Then I click the "continue to this website (not recommended). After this it will not connect
Tried with IE9 and Firefox 11
Firefox says "The connection to the server was reset while the page was loading."
Internet still works. PC is connected directly to router. Tried different port on router. Tried installing CiscoConnect.E2500.1.4.11299.0,0, but it fails saying there is no router connected to PC. Like I said I am on the PC now, wired to router and have internet access via cable modem connected to router. I can see my ireless printer on the network also..
View 2 Replies
View Related
Oct 26, 2012
I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.
View 9 Replies
View Related
Jan 19, 2013
I have a WRT54G router that I have not used for many years, but now I need to use it again. I have connected it between my modem and PC, and I am able to get an internet connection on the PC, but I am unable to connect to the router's configuration page. I have tried resetting the router numerous times (holding the reset button 5 seconds, 10 seconds, even longer) to reset the IP address to the default 192.168.1.1 address, but still cannot access the page. The power LED is on and the WLAN and Internet LEDs are on, and the LED for the port my PC is connected to is on. The hardware version of the router is v3. I tried downloading the latest firmware, but without being anble to communicate with the router at the IP address I cannot update the firmware. How can I go about connectiong to the router's setup page? When using ipconfig, the Default Gateway appears to still point to my ISP's IP address instead of the router's.
View 9 Replies
View Related
Oct 16, 2012
I have updated the WRT160n firmware and, since then, I couldn't access the setup page anymore. I could still use the router as a switch, but couldn't access the setup page and configure it as a router.
View 5 Replies
View Related
Nov 29, 2012
I'm able to connect to the internet through my E1200 router but I cannot access the router set up page. 192.168.1.1 doesn't work... I can connect to it just fine with my laptop however... so I changed it to 192.168.254.1 as per some internet instructions. Still can't connect via my desktop... Tried ipconfig /flushdns to no avail. Cleared the internet cache Upgraded the firmware (via the laptop) rebooted the computer rebooted the router... reset the router... After rebooting the router I can type in the username and password to access the router, but it never connects....
View 6 Replies
View Related
Sep 9, 2012
I need to set up a password for my wireless network, but every time I try to access the setup page, the router stops responding. I've gotten as far as it asking for username and password, where I enter admin as the password....and then nothing. The connection times out. I really need to protect my network.
View 1 Replies
View Related
Apr 3, 2012
I just installed new E4200V2. After completing software install, everything appears to be working fine, except that I can't get to the advanced setup page, either through Cisco connect software or from the web page utility. Either way, the advanced settings web page never finishes loading. I am using the correct login information for the web page utility. It accepts the username "admin" and password, but never loads. Browser just sits there. Browser status bar says "waiting for http://192.168.1.1.
View 3 Replies
View Related
Apr 27, 2012
When I had DSL, my WRT54G was my DHCP master for my home network. When I got AT&T U-Verse, their "gateway" became the DHCP master and also the wireless access point. But the signal was not strong enough where I wanted to use it, so I hooked up the WRT54G again. I discovered that if I connected the U-Verse gateway to the "Internet" port on the WRT54G Linksys, then my home network was split in two, which I did not want. The WRT54G access point is physically somewhat distant from my wired computer, so I wanted to keep the U-Verse gateway as the DHCP master. (The U-Verse gateway is a router with four "computer" ports but no "Internet" port.)
I followed instructions on the Linksys web site, and using my wi-fi connected computer I re-programmed the WRT54G to be "Disabled" as a DHCP server. Then I powered down and physically connected the U-Verse gateway to a "Computer" port on the WRT54G. This solved my problem: my distant wi-fi computer now has a good signal, and both computers "see" each other.
However, now I seem to have lost access to the WRT54G setup "web page." Is it possible to access the innards of the WRT54G when its DHCP service is disabled? Or would I have to reset the device to factory configuration and start all over if I wanted to make any tweaks?
View 3 Replies
View Related
Jul 11, 2012
My internet is T1 by Verizon. My mom's company Siemens pays for our internet because she works from home as medical tech support on the phone. Okay so the T1 had to be laid out to our house underground I think because where we live, other brands of internet aren't available. The T1 goes from the box outside into our basement and hooks up to a Cisco 1721 modem. From the 1721 the internet goes out to a wireless router that is sitting right next to it. This wireless router is a Linksys WRT160N V2. We have several cables coming out of the WRT160N V2 to go to the first floor for hardwired connections, but one cable goes to the attic and connects to a second wireless router. The second wireless router is a Linksys E2000. We have several cables coming out of the E2000 that go to the 2nd floor to serve as hardwired connections.Okay so let me explain where things went wrong.
After a storm our power went out. Eventually the power came back on, but every now and then our internet would shut off for like half a day then turn right back on, so our internet was getting really really spotty. The [b]AL[/b] light on the Cisco 1721 would come on every time the internet went out. It was so bad that my mom had to get an aircard from verizon to get internet. So after two weeks of spotty service and arguing with verizon trying to get them to come fix the problem, they said try resetting your wireless routers because they might have "bad data" in the lines causing spotty connection. So we reset the wireless routers by holding down the reset buttons on the back. Well.. this reset all of the settings for the routers which Cisco facilitated set up, and now our wireless routers are out of warranty date so they can't set the wireless routers back up. However, we have copies of the online wireless router set up page, so we thought maybe we could just set them up ourselves.Well the problem is... We don't know how to connect to the wireless setup pages.. I read something on the internet about setting up wireless networks and to type 192.168.1.1 into our browser(Mozilla Firefox) and that would bring us to the wireless setup page. But the page does NOT ever come up.
Another way to find the IP address of our wireless routers would be to try going to the cmd and typing in ipconfig and using the Default Gateway IP address for the browser to connect to the setup page but that doesn't work out either.... Right now I unhooked the Linksys WRT160N V2 and hardlined the Cisco 1721 to the Linksys E2000 to a PC on the second floor because I figured it wouldn't work out if we had two wireless routers running at the same time. Currently the browser is taking me no where at all. It just says "Connecting..." but nothing is loading up at all.I tried hardlining from the Cisco 1721 to my mom's laptop, which is her work computer, and I got no response at all. I figured it might just be her work computer that was messing up and not allowing her to hardline into the 1721 so I tried hardlining the Cisco 1721 straight to the PC desktop on the second floor(we have no other laptops other than my mom's work laptop) and nothing went through. Then my dad says the Cisco 1721 has been configured so it doesn't direct connect, meaning that it has to go through a wireless router.
View 4 Replies
View Related
Jan 6, 2012
I have a Linksys E1000 wireless router, and I seem to have either written down the password incorrectly or am using the wrong one. Regardless, I can not access the web-based setup for the router. Is there anyway to reset the username and password for it?
View 3 Replies
View Related
Jul 16, 2011
I bought wrt54g2 several years ago and everything worked fine until this week. I got trouble with this router now.All the computers at my home couldn't access to this router even just connect to router's setup page at 192.168.1.1. The only way go to setup page through LAN Cable .I'm afraid maybe there's interference channel with my neighbor, then I did some change to router channel already, but the result same. I still couldn't access to the router through WIFI
Fyi, I did upgrade the firmware with the latest one and all the computers distance to the router not more then 5 m and in the clear area
View 6 Replies
View Related
Dec 4, 2011
if it is possible to access a modem setup page with a E4200 router? My router is on 192.168.254.200 and modem(WAG-200G) is on 192.168.254.100, ethernet cable is on internet port on the e4200 and on port1 on the modem. Modem is set is bridge and I set up a ppoe and dhcp on router. Everything is ok, except that i can not access modem setup page to see adsl conection speed and settings.
View 1 Replies
View Related
Oct 7, 2011
set the max download speed of torrent protocole by my router setup page ?My step father currently downloading with torrent and all the internet in the house is pretty slow so i will love to lower he speed so i can use my internet properly
View 5 Replies
View Related
Jan 14, 2008
I have been trying to change my password and all the settings on my WRT54G V8 router today because I forgot the password, and I can't seem to navigate the Basic Setup page. I can log in (most of the time) after resetting the router, but whenever I try to click on a different tab (like "Wireless", or "Security") it comes up with the page saying "This Page Cannot Be Displayed." I'd like to be able to put a password on it (which I have successfully done before on this router) because I live in a college dorm and would like to keep my internet from being bogged down by other people using it.
View 9 Replies
View Related
Apr 9, 2012
I have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable. I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up. I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router. How do I get to the set up of the Linksys at the same time the Verizon is using the same address?
View 5 Replies
View Related
Aug 7, 2011
I was having problems with the speed being between 30-58 kpbs when going through the WRT160N router, whether its hooked up wired or wireless, the speed with both was extremely slow and wouldnt fully open pager or would take dsl day slow. I hooked up straight to modem and I got 100+ kpbs so I figured its not my ISP, so I read that upgrading my firmware might make it faster, so I upgraded and hit and held the reset button for 30 secs like it recommended but now the 192.168.1.1 wont open, I get a message saying it cant open this page
View 4 Replies
View Related
Jun 6, 2012
I bought E900, accessed setup thru 192.168.1.1, upgraded its firmware.. then changed router's IP, it reboots, then went blank, I cannot access the setup page anymore?
View 9 Replies
View Related
Feb 14, 2012
Any setup passthrough mode of the Motorola NVG510 router ATT makes you use with U-Verse to a CISCO 877 or similar, with a block of public addresses they want to use? It is So frustrating that I have to deal with this NVG510. It is NOT a very business class router... I am assuming that I need to put it into "pass through" mode for the Cisco to be able to manage what happens with my assigned public addresses. If there is another way, let me know!
Here's what I plan to do: I've read the "related to" post above, about putting the NVG510 into pass through mode, and I plan to do this as it discusses. I'll assume that works for now. But it will assign the router's WAN IP Address to the router's "outside" interface, not one of my private IP addresses. On the Cisco side, here is what I would do: vlan1 interface is my "inside" private network. Create vlan2 interface using dhcp to get IP/gateway from the nvg510, or set it up manually, whichever works... This interface will be the "outside" NAT interface. But this interface's address will be the router's WAN address, NOT the first of my 5 public assigned usable addresses...
Here is how it will be setup:
interface FastEthernet0
switchport access vlan 2
[code]...
Then - make it my default NAT interface: ip Nat inside source list 110 interface Vlan2 overload
If I stop there... I assume I could then NAT ports from my different private addresses to the various servers in my office. But the router won't have an interface with that first assigned-to-me public address. The reason I ask is that we have a site-to-site crypto- map defined, and the interface it is defined on determines the IP Address it will communicate from. I wanted this to be my own assigned public address, not the WAN address of the router... Not sure how I would do that though... Same with the default NAT assigned to vlan2 - by default machine in access list 110 will get to the internet with the WAN address of the nvg510, not my private address.
Can I create interface vlan3, somehow linked to vlan2, give it the first private address in my block, and then move the cypto-map to this interface, and also change the default Nat to vlan3 now instead of vlan2? ip nat inside source list 110 interface Vlan3 overload
How would I go about doing such a thing? I am not a Cisco expert, I understand just the basics... This is a bit more complicated than I can figure out. Or maybe it is not possible? Will I have to, for any computer that needs unsolicited traffic through the internet to use one of my assigned public addresses, to setup a one-to-one NAT for that address to that internal address? And everyone else is stuck using the WAN address. If this is the case, it is not right... What were they thinking when they designed this router and forced us to use it as a business class U Verse customer? This should NOT be so difficult/complicated.
View 1 Replies
View Related
Nov 7, 2011
I finally decided to go with a e3200 yesterday and picked up one at Walmart. Last night I went to hook it up and had no luck setting it up. Now I have able Internet with a phone VoIP service. After trying to connect several ways, all the router wants to do is sit with a flashing power light. I cannot access the setup page wireless or wired and have tried several methods I found last night.
View 1 Replies
View Related
Jun 9, 2012
I want to do a logging in page for wifi network ,I use IIS to host my page , ASP.net as the page designer and I think but I'm not sure yet that I make my PC work as a gateway by enabling IP ROUTER form the registry ,now what I need is how to make that page available in all wifi users web browsers except the users they logged in ?
View 1 Replies
View Related
Aug 29, 2012
when i was on my linksys setup page 192.168.1.1 i accedently disabled wireless web access now i cant undo it so now i cant use wifi
View 1 Replies
View Related
Mar 13, 2011
I did RECOVERY on my computer. Its a Compac Windows XP Home edition. This computer runs off of my main computer by a router & adapter. My router & adaptor are showing green but the Internet is showing red. Its becuz my high speed Internat service is ATT.my.yahoo.com. which comes through IE. On my newer computer all is fine. My IE works good & all is working. but my IE on my older one which runs with the router wont set up.
View 1 Replies
View Related
Dec 14, 2011
I'm setting up A DAP-1522 in bridge mode. Network setup went fine. When I went to wireless setup I got a blank page, all white no letters, nothing. I've logged out and back in again with the same results.
View 8 Replies
View Related
Jan 25, 2011
When I try to find where to select between the different encryption types (TKIP or AES), I see the info on page 87 of the product manual, but this doesn't match what I see in the Manual Wireless Network Setup screen. You can select WPA Personal (in Security Mode), but there are no further panels below it to select encryption types and enter the PSK. Compare page 30 to page 87. There are extra panels on 87 that don't appear on 30, and I can't find a way to access them while accessing the router.I've got the unit set up and running; works fine with my wireless laptop. It's just that I need to be able to switch between things in order to troubleshoot a setup with an internet radio I'm trying to get running (Grace Digital, which apparently doesn't do 802.11n, only up to g).
View 2 Replies
View Related
Feb 10, 2013
Is there a way to quickly disable Wi-Fi on a N-150 from the router setup page? I have looked on my admin page but I don't see it. I just want to be able to turn the radio on and off from the PC that is connected via ethernet.
View 3 Replies
View Related
Apr 26, 2012
I tried already several times, may be I entered already a name and password, can`t remember. Anyhow this time I was well documented to start again, but after 192.168.1.1, leaving 'name' blank, and password 'admin', this was quoted as wrong name and/or password. What to do to be able to continue now?
View 2 Replies
View Related
