When using my laptop, my mouse will at times not move. Also when typing, the curser will jump from where you are typing to other areas on the page (to the middle of other words, beginning, or where?
View 1 Repliesthe cursor on my laptop started jumping all over on its own accord and I am struggling to gain control of it and various programs & windows are opening of their own accord. I assumed I had some form of Malware (I know very little about computers) so ran various removal scans and a few things were picked up but it continues to do this. My brother brought his laptop round so I could at least use the internet and after 5 mins of being connected to my internet his laptop started to do exactly the same cursor going all over and programs opening - his laptop was perfectly fine until he connected to my internet. Once he took his laptop back home on his own network it was working perfectly normal again.
View 2 Replies View Relatedthe cursor on my laptop started jumping all over on its own accord and I am struggling to gain control of it and various programs & windows are opening of their own. I assumed I had some form of Malware (I know very little about computers) so ran various removal scans and a few things were picked up but it continues to do this. My brother brought his laptop round so I could at least use the internet and after 5 mins of being connected to my internet his laptop started to do exactly the same cursor going all over and programs opening - his laptop was perfectly fine until he connected to my internet. Once he took his laptop back home on his own network it was working perfectly normal again.
View 6 Replies View RelatedI have a 5508 WLC with CAP3502i APs connected to it. I upgreaded the code to the newest 7.2.115.1 code. I am having trouble with laptops that are not physically moving but are moving their connection from AP to AP in the same area. This is in a school and causing a problem with a testing program they are using becuse they drop 2 or 3 pings in the process. I do have the area heavily saturated with AP but that is because of the amount of clients we have connecting to them. There is 8 classrooms in a hallway with 24 laptops in each classroom. Each classroom has an 3502i ap in it. The laptop can be connected to an AP with great signal and move to another AP that still has a good signal but not as great. I don't understand why if I get 4 bars and connected at 144mps it would move to a new AP. These are Lenovo laptos and i have updated their wireless card drivers and set the roaming agressiviness to low but it still happens.
View 3 Replies View RelatedHow can i get the mouse to control the arrow when i connect my tv to my laptop computer;i can control the arrow with the control on the laptop but not with mouse.
View 2 Replies View RelatedWhat is the best method for connecting two PCs to 1 keyboard and mouse?
View 3 Replies View RelatedI have a HP g Series and suddenly my mouse will not work?
View 1 Replies View RelatedThis just started this morning after I got AT&T internet. It keeps freezing up my mouse for like 3 seconds every 10 seconds or so when I am online.. but when I disconnect it, the mouse is perfectly fine.
View 1 Replies View RelatedHow do I resync my wireless microsoft keyboard and mouse. I just switched out my power supply unit and now my keyboard and mouse is not working. It is a model 3000 and has a white usb receiver
View 1 Replies View Relatedi have a little problem with my wireless half mini card, because always, when i connect my wireless mouse into my laptop, my wireless half mini card starts to disconnecting me from wifi.
This problem is happing ALWAYS, when i join my mouse, Roccat Pyra to my laptop. If i join another kind of wired/wireless mouse, my connection to wifi is stable and everything works fine.
So type of my wireless half mini card: wireless half mini card dw1520-N WLAN
I tried to reinstall/ actualize drivers of this mouse and half mini card, also actualized whole Win7 and still having this problem.And for sure, i once more repeat, that i'm having this problem ONLY when ROCCAT™ Pyra – Wireless is connected, with other kind of mouses (logitech/genius) everyhing works fine.
I just bought a Dell XPS 8500 and find that the Dell Bluetooth driver will not detect my Microsoft Sculpt Bluetooth mouse..
View 1 Replies View RelatedI have lost my receiver to a wireless mouse and key board of LOGITECH K260. kindly tell me what should i do to resolve this problem. can i get its replacement from market?
View 1 Replies View RelatedComputer was hooked to router by cat 5. System worked fine. Due to network configuration changes I had to switch to wireless. Now the Mouse is jittery, delayes in movement and freezes.
OS: Windows 7 Ultimate 64
Ram: 16Gb
Mouse: Razer Naga Epic
Adaptor: WUSB600N Vs 1
MB: ASROCK Extreme 7
Processor: Intel 2600K
Video: ASUS ENGTX 580
Im using Dell Inspiron 1440. recently upgraded from W7 home premium to W8 Pro. Im able to use my dell Bluetooth travel mouse with W8 pro but the mouse track wheel is not working and the side buttons too. im able to move the curser, use right click and left click. what should I do to make the side buttons and the mouse wheel to work in W8 Pro.
View 4 Replies View RelatedI have an Inspion N5030 running Windows 8 with the Dell 365 Bluetooth chip installed. Up until recently I was able to use my chip to connect a Sculpt Touch Bluetooth mouse, but as of late, I am not. When I place the mouse into discovery mode I am able to see the mouse, but when I try to connect to it I get an error that says, "That didn't work. Try again and make sure your mouse is discoverable." I know the Bluetooth chip is still working as I am able to control my iPhone from the computer. I have all the updates installed for my system, including the driver for the Bluetooth card.
View 7 Replies View RelatedI recently acquired a Latitude E6510 with Windows 7 Pro 64bit. My Dell DR984 Bluetooth KB/MS receiver works on my Latitude E6400 with win 7 32bit works but fails on the new notebook.
I have tried the Broad-com updater, but it fails with a message that Dell must be contacted. Where can I find drivers so that I can use the DR984 with my new notebook?
I have recently moved, taking my PC (Windows Vista) from the UK to Norway. My Norwegian partner has a Wi-fi network set up in our new home via his cable TV service (Lyse) and I purchased a Netgear wireless network adaptor so I could get into this. It says I am connected to his network and I entered the correct network security key but I only get 'limited connectivity' which seems to not include internet access. 2 iPhones & 2 other laptops regularly network in so there is nothing wrong with the network per se. The trouble seems to be that mine is a desktop PC.
I had a LAN from home in my 'connections' so I deleted that (and deleted my UK broadband connection) and in the LAN settings box, I unchecked 'automatically detect' & and checked the proxy server box.
I need to move from ASA 8.4(1) to 9.0(2). Reading [URL] it seems to be a quite safe upgrade cause I do not have IPv6 ACL and I have only IKE v1. The following is not very understandable to me,No Payload Encryption for export—You can purchase some models with No Payload Encryption. For export to some countries, payload encryption cannot be enabled on the Cisco ASA 5500 series. The ASA software senses a No Payload Encryption model, and disables the following features:
#
–Unified Communications
#
–VPN
#
You can still install the Strong Encryption (3DES/AES) license for use with management connections and encrypted route messages for OSPFv3. For example, you can use ASDM HTTPS/SSL, SSHv2, Telnet and SNMPv3. You can also download the dynamic database for the Botnet Traffic Filer (which uses SSL) and redirect traffic to Cloud Web Security. Reading [URL] under 'Limitations and Restrictions' I find this point moving to 8.4(2), which I also dont understand,Currently in 8.4(2) and later, the PAT pool feature is not available as a fallback method for dynamic NAT or PAT. You can only configure the PAT pool as the primary method for dynamic PAT. For example, if you enter the following twice NAT command that configures a PAT pool (object2) for fallback when the addresses in object1 are used up, you see the following error message:
hostname(config)# nat (inside,outside) source dynamic any object1 pat-pool object2
interface round-robin
ERROR: Same mapped parameter cannot be used to do both NAT and PAT.
ERROR: NAT pool allocation failed.
You can alter this command to make it PAT-pool only by removing object1; the PAT pool is used as the primary method, instead of as a fallback method:
hostname(config)# nat (inside,outside) source dynamic any pat-pool object2 interface
round-robin
(CSCtq20634)
Is there any other point I need to consider moving from ASA 8.4(1) to 9.0(2)?
I have a 'Comcast Business Gateway' a friend gave me and I would like to use it instead of the regular gateway. The business gateway has extra Ethernet ports on the back where as the regular gateway just has one for your router. I plugged in the business gateway and I couldn't access the network. I used 10.1.10.1 which I thought was comcast's default but to no avail. I am not a tech so I am now stuck.The whole reason I am trying to do this is because the wireless routor is in the house, with a ethernet wire running to the shop. This distance is about 60 feet. I have the computer pluged into the wire but I can't get the printer or the other computer to connect to the wireless. I would like to connect the Business Gateway to the house wireless and then run the hard wire to the shop and connect another wireless router to the wire and run the shop on its own wireless. I tried one of the wireless extenders and it does not have enough juice.
View 1 Replies View RelatedIt was so much easier to transfer from xp to win7, but now that I upgraded both to win7 I can't just simply share it and transfer my files. I need to share 1 entire drive, what's the easiest way to do it.
View 4 Replies View RelatedHere's what I have so far which involves 3 computers:
PC1 has : Window XP w/ Linksys WRT54G w/ Linksys software installed
PC2 has : Windows 7 connected to router via cable
PC3 has : Windows XP connected to router via wireless
My goal is to make my new Windows 7 (PC2) the primary computer just like a server which handles the router and other stuff like printers, scanners, etc. I want to swap the Linksys WRT54G on PC1 to be on the new PC2 (Windows 7) so that the router can be configured and monitored on that machine.
My guess is that I just simply install the Linksys WRT54G's software to PC2 and make the necessary settings just like the XP machine (PC1) and I'm done. Do I need to UNinstall the router's software on the PC1 (XP) machine first? Do I disconnect my internet connection on my PC1 machine?....or do it really matter?
I have 2 computers hooked to a network, both have windows XP I want to get rid of the computer that the printer is physically connected to and move it to the other pc on the network?
View 2 Replies View RelatedI had a home network with 2 laptops (one XP and one Vista) and 1 desktop (XP) configured through a Lynksys wireless router. There was already a Canon wireless network printer (with the Vista laptop set up as the "host" pc). This Vista laptop had to be on in order to print from any of the other 2 computers on the network. I then added another laptop (this one with Windows 7 64-bit OS) to the same home network (using workgroup), and I can print wirelessly from it in the same way (the older Vista laptop has to be on). The Vista laptop is hardly ever used since adding the new Win 7, and I would like to be able to print without having the Vista laptop on. How would I go about this? Do I have to delete the printer from the Vista laptop and re-install on the Win 7? It seems like there should be a way to let the router be the "print server," but I have no idea how to accomplish this. The WLAN settings on the printer all indicate the proper router settings from the initial setup. The printer is a Canon MX860.
View 8 Replies View RelatedI am moving a Windows Server to a new location. We currently have static IPs but are not using any of them so at the new location I requested no new static IPs. With that being said is there anything I need to worry about when I move? From what I have heard it should be a turn it on and go type of move.
View 1 Replies View RelatedRecently I have noticed that my browser, both firefox and chrome are loading rather slowly, as well as any type of streaming media, and downloads. I have performed spyware/adware checks and haven't come up with anything major. I am kind of at a loss as to where to begin to diagnose the problem. I had not installed anything new on my pc before this started. Also my laptop that is on the same network is running fine.
View 3 Replies View RelatedI've typed this question 4 times and keep losing signal so sorry if it appears multiple times, i have moved rooms and my laptop, toshiba satellite is now getting very weak signal. i bought a netgear usb adapter but it doesnt solve the problem much.
View 9 Replies View RelatedMoving into a new spot and some of the computer will be forced to go wireless. Is it better to have an adapter or an actual built-in PCi card?We play a lot of games, so that is my main concern, will we notice a big difference? The router that I am using is a WND3700 with latest firmware update.
View 3 Replies View RelatedCurrently I'm with a pure Cisco shop, running every LAN Switched infrastructure (even in the HQ datacenter) with PVST+, I'm noticing in the documentation I've read and labs I've created that RSTP is... great, and I've observed that even the uplinkfast functionality seems to be build in by just enabling rapid-pvst. Of course I'll propose a migration plan, document the network, diagram it entirely and provide effective steps to implement the change, but that's assumed from any get'go.
View 1 Replies View RelatedIs a protocol inspection or something like it that allow MSDTC flows avoiding to open a backward rule will all ports?
I have for FTP and other protocols as ICMP too but MSDTC ?
Currently trying to set up the above so that if an access service is not matched then it will go to the next one. Looking at the logs what happens is - our auth is set to AD so it matches that - then it isnt in the correct ext AD group and goes to default deny access.
Cant see how to get around this - the only continue command is in the advanced area of the auth - but i cant set up ext ad groups on the auth. How do i get this to move between access services if it doesnt match the ext AD.
We have an old Cisco 2600 series router, running a single T-1 line, AT&T is the carrier. Very standard stuff.
The T-1 works perfectly on the old router. Cisco 2600 with a WIC-1DSU-T1 card. We have a brand new 2911 router with a VWIC3-1MFT-T1/E1 card in it. The circuit runs 100% clean and trouble free on the old router. When I plug it into the new router, it shows up/up but has a massive number of errors on the line, and the circuit is not usable. There are no timing slips or anything like that.
I have another site using the same router and card with the same configuration on that T-1 and it works perfectly. Zero errors. This site (in a different city) is totally slammed with errors. We already replaced the T-1 card and still have the exact same issue.
I've actually been doing this a long time, and I've tried all of the usual things, adjusting line build out, changing clock source, checking and re-checking configs. Nothing seems to reduce the error rate.
I personally think it has something to do with the Smartjack. Like maybe their LBO is too high or too low, and the old router card was more/less sensitive than the new one?
This is a layer 1 issue and is not defective hardware or defective configuration. I am looking for T-1 insights or bugs/issues.
I used my Pix config to setup the ASA 5505.Everything seems to be right. I used ASDM to view settings and it seems right. I am missing something minor, but I am going blind looking at it.
I can remote into the network from outside, but internatlly I cannot get out of network. No internet or email is passing through.
: Saved
:
ASA Version 8.2(5)
!
hostname textasa
domain-name testcorp.com
enable password 579oWRzSY5syo9yt encrypted
passwd 579oWRzSY5syo9yt encrypted
[code]....
I have a customer moving from a 5505 to a 5510. They are currently running websense express, which monitors and filters traffic based off of a port mirror on the ASA. Can this function still be performed on the ASA5510? If so, I am having trouble figuring out the method.
View 6 Replies View Related