HP G Series - Mouse Frozen?
Feb 11, 2012I have a HP g Series and suddenly my mouse will not work?
View 1 RepliesI have a HP g Series and suddenly my mouse will not work?
View 1 RepliesWe have one cisco 871 and five cisco 851 routers , all those routers are connected to each other using site to site VPN tunnels, so each router have 5 tunnels, we are usong thhese routers for IP phones, each location have 2-3 IP phones and 2-3 computers, all routers are connected to internet using ADSL modems,
out of these 6 locations 2 cisco 851 routers are getting frozen once or twice a day, and we need to reboot them, I already changed the router at one location with new one but problem is still there, but if i look for the logging ( Show logging ) its shows only interface up and down status that because of reboot, i cant find what is the reason these cisco 851 routers have 4 port LAN swithc in built, that still works even router is frozen, i was not able to ping or access the router not even using console.
laptop has frozen on "this programme cannot display the webpage". cannot access start menu, task manager or anything else. Can turn off with power button but when it comes back on it flashes on the desktop then reverts immediately to the "this programme ........." page again.
View 1 Replies View RelatedAll my gmail accounts open normally to the first page, but the mouse cursor just highlights whatever I hit. It will not open to the relevant messages or any other action.The sign out function works, so I can go to my other accounts, but the same problem persists.It had been working fine for several years.All the accounts are fully functional when I use my ipod or go to another desktop.
View 2 Replies View RelatedRecently we ha a Nexus 7010 with a module frozen that was OIR (Online Remote and Insert) but do not work until reload the Nexus 7k.The command "show tech-support" has the following:
exception information --- exception instance 64 ----
Module Slot Number: 1
Device id : 147
Device Name: 0x93
Device Errorcode: 0x9329201
[code].....
Was is Excessive Interrupt Events? Can this "Minor Error" frozen the system?Is the port 42 on module 1 affected? o was 42 ports?
My Cisco 871w still stops working once a week.Today I found it frozen, after the weekend, and I have executed few commands from the HyperTerminal .The commands were given by cisco coleagues in previous post :show logshow ip int briefshow interfaces counters errorsshow interface FastEthernet1show interface FastEthernet1 statshow interface FastEthernet1 summaryshow interface FastEthernet1 switching
View 4 Replies View RelatedI have had this wireless router a year or two and it had been working fine until late last night when it just quit. It will not connect to any wireless devices in the house. When my main PC is connected to the router, I cannot get on the internet at all. If I plug my PC directly into my DSL modem the internet works fine. I tried the reset button on the router and still nothing. When the router is connected I get this message:"Limited or no connectivity. You might not be able to access the internet or some network resources. This problem occured because the network did not assign a network address to the computer"It's very hard to troubleshoot the problem on the internet because if I have to connect the router to try something then I lose my internet connection.I hate when things quit working spontaneously. Absolutely nothing changed when this issue started. One minute it was working fine and the next it wasn't.
View 1 Replies View RelatedHow can i get the mouse to control the arrow when i connect my tv to my laptop computer;i can control the arrow with the control on the laptop but not with mouse.
View 2 Replies View RelatedWhat is the best method for connecting two PCs to 1 keyboard and mouse?
View 3 Replies View RelatedThis just started this morning after I got AT&T internet. It keeps freezing up my mouse for like 3 seconds every 10 seconds or so when I am online.. but when I disconnect it, the mouse is perfectly fine.
View 1 Replies View RelatedWhen using my laptop, my mouse will at times not move. Also when typing, the curser will jump from where you are typing to other areas on the page (to the middle of other words, beginning, or where?
View 1 Replies View RelatedHow do I resync my wireless microsoft keyboard and mouse. I just switched out my power supply unit and now my keyboard and mouse is not working. It is a model 3000 and has a white usb receiver
View 1 Replies View Relatedi have a little problem with my wireless half mini card, because always, when i connect my wireless mouse into my laptop, my wireless half mini card starts to disconnecting me from wifi.
This problem is happing ALWAYS, when i join my mouse, Roccat Pyra to my laptop. If i join another kind of wired/wireless mouse, my connection to wifi is stable and everything works fine.
So type of my wireless half mini card: wireless half mini card dw1520-N WLAN
I tried to reinstall/ actualize drivers of this mouse and half mini card, also actualized whole Win7 and still having this problem.And for sure, i once more repeat, that i'm having this problem ONLY when ROCCAT™ Pyra – Wireless is connected, with other kind of mouses (logitech/genius) everyhing works fine.
I just bought a Dell XPS 8500 and find that the Dell Bluetooth driver will not detect my Microsoft Sculpt Bluetooth mouse..
View 1 Replies View RelatedI have lost my receiver to a wireless mouse and key board of LOGITECH K260. kindly tell me what should i do to resolve this problem. can i get its replacement from market?
View 1 Replies View RelatedComputer was hooked to router by cat 5. System worked fine. Due to network configuration changes I had to switch to wireless. Now the Mouse is jittery, delayes in movement and freezes.
OS: Windows 7 Ultimate 64
Ram: 16Gb
Mouse: Razer Naga Epic
Adaptor: WUSB600N Vs 1
MB: ASROCK Extreme 7
Processor: Intel 2600K
Video: ASUS ENGTX 580
Im using Dell Inspiron 1440. recently upgraded from W7 home premium to W8 Pro. Im able to use my dell Bluetooth travel mouse with W8 pro but the mouse track wheel is not working and the side buttons too. im able to move the curser, use right click and left click. what should I do to make the side buttons and the mouse wheel to work in W8 Pro.
View 4 Replies View RelatedI have an Inspion N5030 running Windows 8 with the Dell 365 Bluetooth chip installed. Up until recently I was able to use my chip to connect a Sculpt Touch Bluetooth mouse, but as of late, I am not. When I place the mouse into discovery mode I am able to see the mouse, but when I try to connect to it I get an error that says, "That didn't work. Try again and make sure your mouse is discoverable." I know the Bluetooth chip is still working as I am able to control my iPhone from the computer. I have all the updates installed for my system, including the driver for the Bluetooth card.
View 7 Replies View RelatedI recently acquired a Latitude E6510 with Windows 7 Pro 64bit. My Dell DR984 Bluetooth KB/MS receiver works on my Latitude E6400 with win 7 32bit works but fails on the new notebook.
I have tried the Broad-com updater, but it fails with a message that Dell must be contacted. Where can I find drivers so that I can use the DR984 with my new notebook?
Ciso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies View Relatedwhy I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies View RelatedWhat's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedDoes AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies View RelatedI have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies View RelatedOur house has a cat5 line that runs from downstairs, around the outside of the house to an upstairs office. We are consolidating all the outlets that are randomly spread around the walls. The cat5 cable is about 6 inches too short to reach the new box so we figured we might as well run a new cat6 line. (I think we can make the run 20 feet shorter so that's a bonus.)The cat5 line has 2 jacks wired in series at either end. Everything I've read says cat6 is much more touchy and you should only expose the minimal amount of wire from the sheathing and don't untwist the pairs more than necessary. Can I put two jacks on each end of the cat6?
View 4 Replies View RelatedSome Routers support DHCP spoofing (zyxel / speedtouch).With DHCP spoofing (or half bridge) you can directly spoof you'r public IP address to the firewall. Firewall gets public IP address directly from modem. Benefit of this (no waste of an extra IP address). Modem has no IP address. It has to be possible with an 8xx series router I heard, but I cannot find how.I guess it can be done with a bridgegroup with the dialer and VLAN 1 in it (no ip addresses given).I tried but without any result.
View 2 Replies View RelatedWe've just discovered it seems the 2800 series aren't getting IOS 15.2?
We're running a 2851 for our CME and specifically want some features in CME 8.8...
End of Sale has been announced, but as it stands you can still purchase this router new today.
I have some simple rules on 2 extended lists:ip access-list extended FWINpermit tcp any host 192.36.86.231 eq ftp-data ftp 22 www 443 516 666 671 672 2222permit tcp any host 192.36.86.231 eq 4500 8008 8443permit tcp any host 192.36.86.231 range 5900 5950permit tcp any host 192.36.86.231 range 33434 33550permit tcp any host 192.36.86.241 eq ftp-data ftp 22 www 1935 2195 3306 8888permit tcp any host 192.36.86.241 range 8080 8090permit tcp any host 192.36.86.241 range 33434 33550ip access-list extended FWOUTpermit tcp host 192.36.86.231 any eq ftp-data ftp 22 www 443 516 666 671 672 2222permit tcp host 192.36.86.231 any eq 4500 8008 8443permit tcp host 192.36.86.231 any range 5900 5950,The issue is that 192.36.86.231 can access internet, and 192.36.86.241 can not.Is there a way to troubleshoot 192.36.86.241's connection/packets flow?
View 1 Replies View RelatedI am looking for a Cisco document that gives me the,IP through-put on 2901, 2911 and 2921 routers with Policy based routing applied.,IOS version 15.1.3TOther processes, EIGRP Stub, VLAN routing, SRST,MGCP gateway (analog and PRI).
View 1 Replies View RelatedI have a ADSL and ESHDSL service being delivered to a client site and then using HSRP to ensure that ADSL is provided first and ESHDSL will take over after. The ESHDSL is dedicated for DVTIs to branch offices and that works fine, however I want to provide redundancy for incoming services such as SMTP/RDP etc. but when I forward these ports or a direct IP NAT traffic can only flow if directed to the ADSL service because HSRP is masking the route back and since it came in on the ESHDSL router the ADSL router does not know what to do with the traffic and hence drops it.
How to make it so both routers can port forward with HSRP?
how can i add two printers of different hp series to the same local network ?
View 1 Replies View Related