Cisco WAN :: HSRP And NAT On 800 Series
Feb 15, 2011
I have a ADSL and ESHDSL service being delivered to a client site and then using HSRP to ensure that ADSL is provided first and ESHDSL will take over after. The ESHDSL is dedicated for DVTIs to branch offices and that works fine, however I want to provide redundancy for incoming services such as SMTP/RDP etc. but when I forward these ports or a direct IP NAT traffic can only flow if directed to the ADSL service because HSRP is masking the route back and since it came in on the ESHDSL router the ADSL router does not know what to do with the traffic and hence drops it.
How to make it so both routers can port forward with HSRP?
View 7 Replies
ADVERTISEMENT
Mar 8, 2011
I want to configure HSRP between two different series routers. In my case the router are 3825 and 3925.
View 7 Replies
View Related
Oct 31, 2012
How to configure HSRP in techroutes 2600 series router and aaa authentication
View 2 Replies
View Related
Mar 6, 2012
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies
View Related
Jun 2, 2012
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
View 3 Replies
View Related
Jul 24, 2012
What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies
View Related
May 27, 2012
My Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies
View Related
Jun 14, 2011
Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
View 1 Replies
View Related
Jan 17, 2011
I have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
View 2 Replies
View Related
Nov 16, 2012
following is the capture of my configuration of HSRP on two switch layer 3 (LAB)
View 19 Replies
View Related
Feb 13, 2013
I'm screwing around with HSRP running between two L3 interfaces of routers. I placed an inbound and outbound ACL on the same interface on both of these routers specifying to "permit ip any host 224.0.0.2" Why am I only seeing counters ticking for the inbound ACL of both of these routers? Is it an order of operations thing?
View 3 Replies
View Related
Dec 6, 2011
I have a pair of physical ASR 1002 routers, called ASR-1 and ASR-2. I setup HSRP on both ASR-1 and ASR-2 on both g0/0/0 and g0/0/1 interfaces, nothing complicated, just straight forward HSRP.
Now Cisco TAC told me that HSRP is NOT supported between physical ASR routers. WTF!
Furthermore, they told me that HSRP only supported within a single ASR because of multiple routed processors. In other words, you can setup HSRP with a single physical ASR but not with two physical ASR routers.
HSRP can not supported with two physical ASR routers?
View 8 Replies
View Related
Mar 7, 2012
We want to implement HSRP between two 3945 ISRs:
RouterModelIOSModuleR1Cisco 3945 Integrated Service
Routerc3900-universalk9-mz.SPA.151-1.T.binNME-AIR-WLC12-K9
R2Cisco 3945 Integrated Service
Routerc3900-universalk9-mz.SPA.151-4.M1.binNME-AIR-WLC25-K9
The issue that we are experimenting is that, although the module's interfaces are up and HSRP in correctly configured, the show standby summary displays that the Active router is local in both routers. We also have some GigabitEthernet in the routers and they are correctly running HSRP. Does the WLC Modules physically support HSRP?
View 1 Replies
View Related
Apr 24, 2012
i have a 6509 connected via layer 2 (VLAN1) to a 3750 (e.g. VLAN1 10.1.1.1)then to the HQ via Metroethernet(L3). Is it possible to connect the 6509 to an ASA that already has VPN connectivity to the HQ using HSRP? Also need to mention, the VPN connection is supposed to be the redundant connection if Metroethernet link fails.
View 3 Replies
View Related
Apr 13, 2011
The Issue we have two 3750 switches and configured hsrp on that . Now instead of connecting these two swiches to an Intermediate common switch we have a cisco asa5520 which has 3 L3 ports of which is it possble to convert 2 ports as L2 ports and use those ports to connect to 3750 switches instead of a L2 switch.
View 4 Replies
View Related
Apr 17, 2012
I m a Network engineer in company, we have around 800 users in the office.Below is the details of my network infra.We have 4506 chasis with IOS version of 12.4 (44r) SG3HSRP is configured for redundancy.HSRP is configured on VLAN besis
The problem that HSRP is not working working properly, When my active VLAN goes down, Standby VLAN act as a Active VLAN but traffice is fail to route trought that VLAN and i m not able to ping another vlan from that VALN.
View 20 Replies
View Related
Dec 12, 2012
currently my organization is connected to internet through a checkpoint cluster directly connected to ISP router.I'd like to use both links, placing a brand new 2 cisco router between Checkpoint and ISP routers.
View 14 Replies
View Related
May 18, 2011
I have a 857w and a 857 router but there doesnt seem to be any HSRP and VLAn support on either router. I have ADVsevcurity on the routers
do Ineed a different IOS or is it just not supported.
View 1 Replies
View Related
Oct 11, 2012
I'll have a problem to configure VPN Ipsec l2l between my CISCO ASA 5510 with HA and a remote lan configured with 2 cisco router with HSRP on lan.
I'll configure a static crypto map with the definition of the two peer (master and backup).Sometimes happen that the vpn is instaured with the backup router. The phase2 is up but no traffic pass between the two net?
View 4 Replies
View Related
Nov 13, 2012
I have the following topology:
2x 877 routers, one interface from each router (port Fa0 which belongs to the router internal switch) is connected to the 2960 switch, the switch himself configured with default settings, flat with one v LAN.
I have configured HSRP in the following manner: router A is 10.0.0.2, router B is 10.0.0.3, virtual IP is 10.0.0.1, take note that the HSRP configuration along with the IP address are configured on vlan1 interface.
Now when i connect a PC to the switch with static IP (10.0.0.4) and trying to ping 10.0.0.1 I'm not getting replies. i see on the PC, using wire shark, the icmp request goes out but on the primary router (and also on the backup) i can't see the icmp request (using debug ip icmp).
this behavior happens only when the HSRP is configured on interface vlan1, when configuring the same configuration on Fa4 (which is WAN interface) everything works fine.
View 4 Replies
View Related
May 9, 2011
I just inherited a network which has 7 switches (3750s) as a Stack. In there, there are 5 SVI (switch virtual interfaces) and in each of these VLANs, HSRP is configured.
Question:Is HSRP really needed in a Stack configuration?If so, what are the benefits?Can I simply clean-up the config and remove HSRP?
View 14 Replies
View Related
Feb 3, 2011
I want to run HSRP into my network.i am using two 4503 switch one is main and another one is standby. i configured V LAN into my switch and its running, now i want to configure HSRP. my configure is attach with this mail and my main switch gi2/22 is connect backup switch gi2/22 and all user is connect to both switch as like HSRP network.
I can use Standby ip
10.0.1.252 (vlan-1)
10.0.2.252 (vlan-2)
10.0.3.252 (vlan-3)
10.0.4.252 (vlan-4)
10.0.6.252 (vlan-6).....so on.
View 1 Replies
View Related
Jun 12, 2013
I have 3945 router using the HWIC-4ESW module.I am not able to see the HSRP configuration commands under these interface.Does this module support HSRP ? If yes , do i need upgrade the IOS of router.
View 1 Replies
View Related
Mar 21, 2011
last weekend i configured HSRP on our default gateway(Cisco 2600) and now i have the problem that the latency is constantly at 3ms and from time to time it goes up to 10 ms. Is that something i should have expected or is there someting wrong with my configuration? The standby ip adresses are the same adresses as the router interfaces had before and the CPU utilization is at 10 % so i do not know what happend here. I atached the config file so if you need further information i will gladly provid it.
View 4 Replies
View Related
Jun 15, 2011
I am using two 7609 router in setup, HSRP enable on both router, and both have WAN connectivity to different PE end router we want to enable hsrp feature ip route traking, in case primary link goes down (Because of any reason link bgp failure, PE device issue).
View 1 Replies
View Related
Jan 8, 2012
I want to setup HSRP between three 6509 switches with a single virtual ip for all the three switches.
know if its possible and share any site or config.
View 1 Replies
View Related
Feb 6, 2013
I have two Cisco Routers 3800 series for my internet traffic (2 ISP). I configure HSRP on the interfaces gigabitethernet and at the main router I put the multilink interface to track. When the connection drops to the main router traffic does not switch on my second router.
View 1 Replies
View Related
Nov 11, 2012
I'm looking to try and implement ipv6 HSRP on a series of IOS-XR Routers running 4.2.1 following on from successfully setting up IPv6 HSRP on a few cat6509s on VLAN Interfaces in other parts of the network. I have entered the "router hsrp" configuration menu and gone into the interface in question that I'm looking to setup with IPv6 HSRP. Unfortunately, there version 2 or address-family ipv6 commands are not available.
View 2 Replies
View Related
Jan 24, 2011
I have 2 routers ( Cisco 3845's) both running identical IOS's. Each router has identical 5 networks on it with one network each being different.I have HSRP set up on the identical 5 networks.Your standard Fail over senario.ON one of the routers one network is not seeing the other router in the same network, Will not Ping or traceroute.And HSRP stopped working ( both were thinking they were active. which of course brought the network to a halt. Non of the interfaces has any ACL on them, They are plugged into a Brand new Cisco 3560v2 switch. I have switches out the cables to eliminate that as an issues.
View 1 Replies
View Related
Apr 17, 2012
is it possible to run hsrp on two routers (not l3 switch) connected to a l2 switch ? if so does the two routers need a back to back connection ?
i know if use two l3 switches (instead of routers) and connect to a LAN switch then we need a back to back connection between the L3 switches
also can we use hsrp on vss on 6500?
design
1800 router 1800 ROuter
| |
| |
|---------- L2 switch-------------------------------|
if the above design is acceptable how does the routers know which one is active and which one is standby ? if we need a direct connection between two routers they have to be on a seperate subnet and routers dont allow broadcasts - so how will hsrp work on routers ?
L3 switch --------------------------l3 switch
| |
| |
|---------------L2 switch---------------|
View 8 Replies
View Related
Jan 23, 2012
Planning to implement HSRP in layer 3 switch.
We have two numbers of Cisco 4900 ME Switches. Basically want LAN failover from these devices. There are about 400 users in our network. I have attached rough network topology for your reference(I am not good at Microsoft Visio). Need to know implementation of the HSRP in these switches. Two distribution switches(Cisco 4900 ME Switches) are connected to 4 Access switches and these are connected to the LAN.
View 2 Replies
View Related
Jul 9, 2012
i have 2 cisco 7604 distrubution routers .Both routers are running 310 hsrp groups.
Sundenly there is hsrp flapping which causes high CPU.
What is the limitation of HSRP group on cisco 7604 router .Below is the show ver from the router
----------------- show version ------------------
Cisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVIPSERVICES-M), Version 12.2(33)SRC2, RELEASE SOFTWARE (fc2)
[Code]......
View 2 Replies
View Related
Feb 27, 2013
I have configure multiple vlans on both the core swithces below is the example, my question is how will be my VTP server configuration on the 3560E since both the core switches will have identical vlans HSRP 2 configured on them. Do I have to configure both the cores with same DOMAIN NAME ?
The core has VTP 2 so I cannot use primary and secondary option.
CoreSwitch1
interface Vlan713
ip address 194.43.86.251 255.255.255.0
standby version 2
standby 86 ip 194.43.86.1(code)
View 3 Replies
View Related
