I am currently having trouble with my NVIDIA nForce Networking Controller. Every morning when I turn on my computer, I have no network connections available, even though I am connected to a home network via Ethernet cable. In Device Manager, there is a yellow triangle with an "!" inside beside the following entries:NVIDIA nForce Networking Controller (of course)Standard Enhanced PCI to USB Host Controller
View 5 RepliesI cannot seem to locate a driver for the "Nvidia nforce networking controller." ALL information I can glean from the computer does not show anf further information or part numbers or numbers after "nForce".
HP dv6704nr Pavilion Entertainment PC
I've recently reformatted an old hdd and i've installed windows xp professional on it and as usual the first thing that came to mind was to go on the internet to download all the drivers i needed. I ran into my first problem, apparently i can't access the internet because i don't have the driver that allows me to use the internet. I've downloaded the same driver that i had on the other hard drive, but it's just not doing anything, i can't create a Local Area Network in my connections. I'm on the same computer as said computer, except different hard drive. Don't have any of the cd's nor do i know which drivers were installed on this hard drive.
Here's some of my computer spec's:
Microsoft xp
CPU type: AMD athlon 64, 2000 MHz(10 x 200) 3000+
Motherboard Name: ECS nForce3-A(5PCI,1 AGP, 2 DDR DIMM, Audio, LAN)
Motherboard Chipset: nVidia nforce3 250, AMD Hammer
System Memory: 1024 MB
BIOS type: Award(09/16/05)
Network Adapter: NVIDIA nForce Network Controller - Packet Schedular Miniport
when i connect an eth cable to my pc everything says its doing its job righht ie driver up to date etc but i cannot get it to show as connected , all i get is that a cable is unplugged warning .
View 8 Replies View RelatedIt keeps saying the connection between the modem and the computer is broken. I've installed a new ethernet cable. it works then it drops. we have hughes net here. the techs have been out and cannot isolate the problem.
View 3 Replies View RelatedI recently installed windows 7 ultimate and my NVIDIA GeForce 7000M /nForce 610M can not connect. I re-installed the drivers and it still can not start. only my wireless works. Compaq pressario f763nr laptop.
View 1 Replies View RelatedI have an HP Pavilion notebook that was given to me by a friend who had upgraded to a new computer. Due to the fact that she no longer remembered the password to the computer I did a clean install of Windows Vista Home Premium to gain access to the computer. Unfortunately, while the computer seems to be running perfectly, when I attempt to find network connections my computer not only can't find wireless connections, but it doesn't even allow the option of manually creating a wireless connection under my Internet options.My computer has a built in NVIDIA nforce Network controller listed under my network adapters and when I check its status it states that it is working properly, yet it doesn't detect any wireless networks. In addition to this, I've read online that the wireless indicator light on my computer should switch from orange to blue when turned on, but even with my wireless switched on the light remains orange.I've also clicked the update drivers option on the NVIDIA network controller, but it states that the drivers are current and changes nothing.
View 14 Replies View RelatedI have just wired my house and have a cisco 2950 switch running in the basement. every rj45 jack in the house works with everything except one computer. we have a HP with an nforce 4 chipset. this computer was connected through a hub and to a netgear router using the wires in the walls, the same wires and ends this switch is connected trough now. This computer stoped detecting a connection when we moved it off the hub and to the switch. all the ends and punch downs are using B wiring pinout. I have tried a new cable, when i plug any cable from the wall jack to this laptop it works, when i move the same cable to the HP it does not detect any cable plugged into it. when i setup ICS on this laptop it will connect and does detect the connection with the same cable running from the wall jack to the HP that it previously did not detect.perhaps the HP wants to use the 2 pairs that are other wise dormant? im about to install a new nic and see what that does but i can not understand why the Nforce nic would not connect to a cisco switch
View 3 Replies View RelatedNVIDIA is blocking my internet connecting on only one of my computers and it has become somewhat of an urgent situation. I need to know how to get rid of it immediately. I have no idea what NVIDIA is. I was using my computer and going on the internet without a problem and 3 hours later this issue came about.
View 2 Replies View RelatedAfter getting the cable set up (some new wireless modem that comcast gave us) we were able to connect to the internet once, after putting in the password, but after that the next day our computer would not recognize any networks at all, it's just say no connections are available.I already:-restarted computer,-reset modem (we used to have a router and a cable modem but now only the wireless modem)-rolled-back drivers,-disabled then re-enable driver (did NOT uninstall or reinstall)-opened the computer up, take out the adapter, tryed and got the dust off-unscrewed and rescrewed antenna- tested a laptop, and it had an internet connection - and probably a few other things which I can't rememberLast time on the computer, I uninstalled a few things with revo, ran registry cleaner, browsed internet, and installed a new nvidia driver (after the problems arose). I was able to install a netgear wireless usb adapter (which is how I'm on the internet right now), but it frequently gitters and I can't use the NetGear for very long seeing as how a different computer uses it.
View 3 Replies View RelatedI have reinstalled XP on an older PC and have run Driver Reboot to check all the drivers are ok. So far so good, except - I cannot get onto the internet.... router etc is working... have reinstalled the nvidia nforce networking controller (as this kept coming up with errors). When trying to connect, error message is: limited or no connectivity.
View 5 Replies View RelatedMy computer is a Dell Inspiron desktop 531S. I use Windows Vista.
I have an NVIDIA GeForce 6150 LE INT with integrated NIC card. The ethernet port isn't recognized though. I have downloaded all the latest drivers and updated my BIOS and everything I found listed about.
I just installed nVidia Nforce drivers for my Asus 750i motherboard, I show I have internet connection, however I can not get windows to pull up a site. TRIED everything reset modem, router, checked all settings. When I pull up the networking system information, it states connection status: disconnected via the Nvdia controll panel. Reset everything back to factory defaults still nothing....IT was working, I intalled I tunes, and then it stopped....I uninstalled Bonjour thinking that it might be the issue....nothing
View 1 Replies View RelatedI have an Acer AX3400 (windows 7). I'm trying to install wireless router Netgear WNR3500v2. I did not succeed sofar. Do I have to uninstall NVIDIA drivers first?
View 1 Replies View RelatedI recently installed a very basic version of XP on my old laptop (Gateway MT3707).After hours of searching for the correct drivers, I found them, and installed them. After installing the correct drivers for wireless internet I was able to pull up the list and find my network on it.When double clicking on our wireless network it asks for a network key (also called WEP key or WPA key).Now we have a password for our network, but after an exhausting amount of tries that won't work. I not sure if that is what its looking for. In our apartment we run mac OSX, windows vista, etc., but usually the password for the network is satisfactory. I have never ran into this problem.I hate to be a noob, but I don't know where to go from here.
View 6 Replies View RelatedI know that the 3600 series APs are not supported on the 4404 WLC. However, would the following scenario be supported? I would like to use the 4404 (software rel. 7.0) as a guest anchor with a 5508 (software release 7.2) as the foreign controller supporting series 3600 APs. I ask because the APs do not need to join the guest anchor.
View 7 Replies View RelatedWe have a customer that have 2 5508 as primary and backup controller and a 4400 as an anchor controller. We plan to upgrade the 5508 to 7.3.112.0 and the 4400 is already 7.0.116.0. Will there be any issue if the anchor controller is not the same code as the foreign controller? Do I also have to upgrade the acnhor controller to 7.0.240.0?
View 2 Replies View RelatedWe are trying to navigate the waters in choosing between a in-house, controller-based, wireless network solution or a cloud-based solution. We have been presented with the usual suspects in cloud-based (Aerohive, Meracki, etc) and with Cisco (5500) and Aruba on the other side. We are a multi-campus organization with approx. 200 APs.Any hard reasons why go with a controller-based vs. cloud-based solution? If we must keep the conversation limited to Cisco, why go Meracki over Cisco's WLC solutions or vise versa?
View 1 Replies View RelatedI am looking to configure a wired and wireless guest network. I have industrial barcode scanners that connect to one SSID and then there is the business network on the office SSID (no vlan seperation for these devices just different SSIDs). There is not really a need to seperate the business network from the scanners in any case. However, there are needs for a guest network and this needs to be seperated. At the bare minumum I would like to have the wireless guest network. Here is what I have: 2125 Wireless LAN controller managing 18 LAPs (1 indoor and 17 outdoors)Cisco Cat 2950 switches (2 x 24 port and soon to be replaced with 2 x 48 port 2960's with 802.1x capability) Sonicwall TZ210 firewallOne existing wired and trunked vlan for PLC infrastructure. One ESXi hosting Windows server guests (soon to be 2 with vMotion) The reason for the wired guest access network is tp prevent anyone from plugging into the wall jack in the office with thier home laptops or anyone else from being on the same subnet as our domain machines. Granted they would be unathenticaed but there would be no layer 2 seperation and that is what I think would be best.
How would I go about doing this on the wireless controller without an anchor controller just using my existing hardware? I would like to have the Guest SSID only availible in the front office. Is it possible to offer a guest network while still servicing the business network SSID on the same access point? Then might I be able to have the guest network be treated as it should at the controller? However this might present another issue altogether as the guest traffic will be over the same wire as the business SSID until it hits the controller for management.
Having some serious problems on the networking front here at home. I have 3 PC's and 2 Xbox's that run constantly. Our Internet bandwidth is Insight's 50.0 which is 50Mb download speed 5Mb upload speed. The problem we're having is this. Ever since we upgraded from dual 20Mb lines on a Cisco RV042 to a 50Mb on a DIR-655 we've been having latency issues. I have everything turned off in the router. It's basically there to give out IP numbers and thats it. All security is handled from the PC's themselves. Bandwidth tests are fine, I sustain download speeds above 7MB/s using download managers. But pings are terrible. Xbox live is terrible, PC online gaming is terrible. Pingtest.com is terrible. Only when behind routers. I've tried it behind 3 seperate routers. The DIR-655, the Belkin f5d8236 that insight provided me, and the cisco rv042 originally used for dual wan routing. all of which are met with serious failure.
If I plug directly in to the modem pings are fine. Add a router and pings go to shit.
I have 3 LAN connections. I m using 3 modems and 3 switches to connect all the pcs in LAN.but now i want 1 pc as a server which have connected all the 3 lan network with it.so that everyone can share its file to server and even all clients. Should i have to create VPN or homenetwork to connect with server? and i must have to install microsoft windows server in server pc?
View 4 Replies View RelatedMy laptop (Win 7 x64) can currently access all the shares on the XP computers in my home network but,although I can see it, I cannot access the laptop from my main xp computer. I haven't tried to access it from the other xp computers downstairs. I have read the guide on this site as well as 3 or 4 other threads on this subject but am unable to resolve the issue. Completing the network setup so that I can look into my laptop from this main xp computer. My laptop has a wireless internet connection but I also have it plugged into my wired home network for sharing. I will provide other details as needed. I suspect that some essential services for file sharing may not be running on the laptop, but I'm not sure.
View 19 Replies View RelatedI have been looking at ways of networking my printer in my office. The problem being that my printer does not have any kind of inbuilt networking capacity.So I thought I could connect it via USB to my router as it has a USB port on it.The router is an Orange Bright Box - In the specs for the router it says that the USB port is for file sharing, mentions nothing of connecting a printer to it
View 2 Replies View RelatedTrying to network between a Windows 7 computer and a Windows XP computer is possibly the hardest thing I have ever done.I have googled for hours and hours and none of the solutions seem to be working.I will try to explain what I have already done. Although I have done loads and I am sure I am missing some things.I have a Windows 7 laptop and for this exercise I shall call it WIN7. I have a Windows XP computer and for this exercise I shall call it WINXP.Both computers are in the same network which I have called SAMNETWORK. I have enabled permission to Everyone in folder sharing settings on WIN7. I have turned on Sharing and I have made myself discoverable with no password set on Network and Sharing Advanced Settings. Both user accounts on the XP and 7 machines are the same and both passwords are the same. I have turned all firewalls off. The WINXP computer has sharing enabled.
I have done a lot more things including installing LLTP (sp.?) and changing registry entries like Lsa/anonymous something like that (can't remember the actual directory) but I have changed registry entries as I have read elsewhere on the web and I have changed the network from home to work but that did nothing etc. etc. But everything that everyone suggests is just not working and I have been looking for about 4 hours now so you can imagine I have tried everything I have found!Anyway, my 7 laptop can see WINXP but when I click on it, it states that Windows cannot access \WINXP. The WINXP computer can see shared folders from WIN7 but it also states that it is not accessible. However, I did once get the WINXP computer to access the WIN7 shared folders. However, that doesn't even work now. I need the WIN7 to access the WINXP files. [code]
Running Windows XP Im a bit Dizzy as i can't seem to workout what's going wrong or what im doing wrong lol!!!8 Pc's on the network, all can view files etc.apart from one Pc Lets just call this "Bob1"It keeps asking for user name and password, now there's no user name or password on the giving pc, file and sharing is open and all the right ports giving. what i can't understand is that the reaming 7 pc's on the network has the same setup and files permissions, on the same subnet and can ping each other to my knowledge.So just to prove myself wrong i made a password for the pc that was asking for one on the network and this still did not work.so to cut the story short 7 pc's can search each other fine but on "Bob1" keeping asking for user name and password.
View 3 Replies View RelatedI am having trouble with setting up connection between pc using windows 7 and a laptop using windows xp. Do I have to setup a separate network on my laptop?
View 1 Replies View RelatedI am trying to use the existing rg-6 in a building for internet but am not sure how far a coax can go and still get a good signal strength?
View 1 Replies View RelatedI am trying to add an XP computer to our (already) Win7 computer.Now...I have connected the xp computer to the external modem that gived the 7 it's signal by way of ethernet cable). I went through changing and matching up the workgroup names, and.....turned on "Network Discovery" on the 7 end....after everything is said and done...I DO get the internet signal to the xp, but knock out the 7, altogether.
View 4 Replies View Relatednetworking error which seems to make no sense to me, i have computer 1 (tower computer) computer 2 (laptop computer 3 (tower computer1 & 2 have networked happily together for 4-5 years, sharing files and printers both ways. 3 was connected and happily joined the network but only with 2. 1 can see files on both 2 & 3, have now disconnected 3, have reset and rebooted router and both computers are up to date with software patches, i can not work out why 2 (or 3 before it was disconnected) can see 1 on the workgroup but can not access 1 in any way. i can, however, copy a shortcut from 1 through metwork places into 2 and access those files from 2. but network wizard or manual setting can not get full sharing.
View 6 Replies View RelatedI am the CEO of a small company with 5 divisions, 2 of which are remote. There is also my home office that I wish to be on the company VPN.We can't afford an IT department, so it is up to me to ask for a network diagram (as specific as possible) that lays out all the hardware required.My plan is to eventually have an intranet web server, file server, and database server all for internal use. Our external webserver is hosted by a well-known company. Growth must be considered both in hardware and network.
View 4 Replies View RelatedI have two NICs and two seperated network connections on Windows Vista System. I want all visits to websites that are blocked by our Corporation LAN go to the external network, so I can use my personal emails etc.All the other applications still use corporation LAN.
1) Corporation LAN subnet: (Connection 1 - DHCP)
IP: 142.241.X.X
Subnet: 255.255.255.0
Gateway: 142.241.X.X
2) External network LAN subnet: (Connection 2 - DHCP)
IP: 192.168.1.X
Subnet: 255.255.255.0
Gateway: 192.168.1.1
When i try to go online it says that i dont have a connection, and that it does not detect any networking hardware. How do i fix this?
View 7 Replies View RelatedI am trying to link a Windows 7 machine with a laptop running Windows XP. The workgroup on both computers is the same. On the Win7 machine, I have a couple of folders set to be shared. The first is the C Drive and the share name is C-drive. The second is Quickbooks that I have named Quickbooks. On the XP machine, I went to map network drive and in the blank typed \Remote1C-drive. It asked for username and password and just like that we were connected. But I can't see all of the files on this drive. I don't even see all of the folders - one of which is Quickbooks. So I tried \Remote1Quickbooks and Windows XP couldn't find that path even though I'm positive that folder is shared on Win7. So no matter what I try, I can't see this folder on the XP machine, I even tried copying this folder to other locations around the computer and setting up shares in hope that something would work, but it never did. So I went back to the C Drive share on the XP machine. I tried to go in reverse, creating a file and putting it on the root of the c drive (I did this on the XP machine, but the file should have actually been located on the Win7 machine. When I check Win7, the file didn't exist. So I tried the other way. I right clicked on the c drive in Win7 and created a new bitmap image file. Back to the XP laptop, that file doesn't show. But if I look at the c-drive on Win7 from the xp machine, I see several other folders and some of them like Program Files contains actual files. But some of them are just empty such as \Remote1C.
View 6 Replies View Related