I want to setup a lap environment for my studies using Microsoft Virtual pc. I have installed 3 virtual pc of which 2 are windows server 2008 named srv1 and srv2, the third virtual pc is running windows XP professional services pack 2 with the host operating system being windows 7.I have installed Microsoft loop-back adapter and i am trying to network the 3 virtual pc and the host.
srv1 ip address is 192.168.2.200
srv2 ip address is 192.168.2.201
wk1 ip address is 192.168.2.10
host pc's ip addresss for the loopback adaptor is 192.168.2.5 when i check the workgroup i see only srv1 and srv2 i am only able to ping srv1 and svr2, the rest are unreachable.
Just purchased an Asus K532-BBR9 laptop. Everything works fine, except on college campus the internet is very slow, and disconnects every few minutes.My fellow students laptops do not seem to have this problem.I figured it may be a driver issue, so I am trying to update everything.Under Network Adapters in Device Manager. The Microsoft Virtual WiFI Miniport Adapter is not up to date when I do a driver update scan.Then it says "Windows can't verify the publisher of this driver software.." with options to install anyways.
I have two computers, one is a Dell Dimension 8300 while the other is a Compaq Presario Desktop. Both use Microsoft Windows XP OS 32 bit and are networked using a Microsoft Wireless G-Base Station MN-700 on the Dell and a Wireless G-Adapter on the Compaq. This arrangement worked quite well for some time and recently they stopped communicating with each other. I reset the base station as described in the manual. When I did the same for the Adapter I could not enter the correct Wireless Security Key. I tried copying the key from the Base to the adapter but to no avail. Do I have to uninstall both units from their respective computers and reinstall from the CD provided?
I am in the process of configuring load balancing on ACE module but struggling to configure virtual IP address for ACE module. I'm working on ACE30 module and using software version A5 (1.2). ACE module is in slot of Catalyst 6504 switch.
I recently installed a very basic version of XP on my old laptop (Gateway MT3707).After hours of searching for the correct drivers, I found them, and installed them. After installing the correct drivers for wireless internet I was able to pull up the list and find my network on it.When double clicking on our wireless network it asks for a network key (also called WEP key or WPA key).Now we have a password for our network, but after an exhausting amount of tries that won't work. I not sure if that is what its looking for. In our apartment we run mac OSX, windows vista, etc., but usually the password for the network is satisfactory. I have never ran into this problem.I hate to be a noob, but I don't know where to go from here.
have a problem with downloading microsoft silver light with both browsers ie mozilla firefox and internet explorer as i click the download button firefox say silverlight server not loading or busy and explorer says page cannot be displayed and i need it really badly as i need to send photos to all my friends.
I cant access microsoft webpage. I have fresh copy of win XP pro SP3, IE 8, and connected through an updated Vodafone ADSL modem through ethernet. Strange thing is, I can access bank, tv over internet, etc. except MICROSOFT webpages.
I have a problem with my 802.1x Solution in ACS Version : 5.2.0.26. The hours between my ACS and the AD lost synchronize, for that reason the user in my network can't authenticate in the Solution. when i see the hours was different for the AD in 5 minutes, i have to force again the common ntp server 172.25.0.34 (which is ip ntp server). I don´t know why is the reason for lost synchronize, maybe could be a bug.. or samething that i have to configurate in the ACS or AD.
We're using Cisco Secure ACS 5.2 as a Proxy AAA server, using Active Directory as an External Identity Store. They are already synced and connected and thus I can login into the VPN using my Domain credentials.
But that's not enough. My client needs to limit who can and can't establish VPN session, I mean, the way it is now, EVERY single employee can do that if his/her credentials are valid in the Active Directory domain controller. So I need to do two things:
1) Using the Microsoft NPS server, via dialin attribute, allow or deny VPN sessions using ACS/ASA;
2) Using the company user credential attribute to identify which Authorization Group the requesting user should be in, Downloadable ACLs will then be applied according to the access policies created for each company.
We have two separate external connections, one behind a pix one behind an asa, clients behind either of these firewalls cannot get to skydrive.live.com - the page title loads but then thats it!im debugging behind the pix becuase there is less traffic and ive pulled this from syslog so far-have been googling but not sure if this syslog data is normal or not really
I can't seem to connect to any wifi. I opened my device manager and looked under network adapters ant there is a little triangle with a ! in it. What can I do to fix this???? I'm a college student who needs access to the internet badly
Running Windows 7 64bit, ISP is EATEL connected through a PACE 3801HGV to a new Linksys EA6500. Since the initial setup ( I was walked through the setup via Linksys support) I cannot access windows update, (the error screen tells me to restart my computer, "Windows update cannot currently check for updates because the service is not running. You may need to restart your computer", and I have done so 25 times) and I cannot update my Microsoft security essentials. Windows firewall tells me that the 'advanced settings snap-in' failed to load. Is it safe to uninstall and try to reinstall these or is there a way to start the services?
I have a LAN running Window server 2000 as domain controller and having 40 client PCs.i want to configure my server as a mail server which is for the time being only a file server. i dont want to use POPS, IMAP or Exchange server.instead i want to use Microsoft Mail to configure my client computers.i have only heard about "Microsoft Mail" mail so far.
I cannot access any microsoft websites except when in safe mode + networking. I can browse all other websites just fine, but can only access any microsoft sites in safe mode.
I'm running WCS 7.0.220.0.I would like to authenticate users that are able to logon the WCS, through MS Network Policy Service (RADIUS).I would like all my domain users to be member of the local group on the WCS "Lobby Ambassador", so all domain users has access to generate guest access accounts, for the web auth... I can see under the WCS Administration under AAA that it should be able to use RADIUS - but i'm not sure how to setup the NPS policy?
Having some serious problems on the networking front here at home. I have 3 PC's and 2 Xbox's that run constantly. Our Internet bandwidth is Insight's 50.0 which is 50Mb download speed 5Mb upload speed. The problem we're having is this. Ever since we upgraded from dual 20Mb lines on a Cisco RV042 to a 50Mb on a DIR-655 we've been having latency issues. I have everything turned off in the router. It's basically there to give out IP numbers and thats it. All security is handled from the PC's themselves. Bandwidth tests are fine, I sustain download speeds above 7MB/s using download managers. But pings are terrible. Xbox live is terrible, PC online gaming is terrible. Pingtest.com is terrible. Only when behind routers. I've tried it behind 3 seperate routers. The DIR-655, the Belkin f5d8236 that insight provided me, and the cisco rv042 originally used for dual wan routing. all of which are met with serious failure.
If I plug directly in to the modem pings are fine. Add a router and pings go to shit.
so i installed ms dynamics RMS 2.0 i think with sql server 2005 express and after setting all up i try to log in through store operation administrator ith the company namesqlexpress it says connectionopen load netlibs but when i change the server to (local) it logs in then i try to open the pos it says [title]store operation business rules :[body]: Can't connect to databasewhile try to open store operation manger it says [title]Database Failure :[body]: could not connect to database.?
I did not put a wep code/passphrase in my router when asked if i wanted it secure. I said yes and router was set up secure but I don't know the code. How do i find it?
How do I resync my wireless microsoft keyboard and mouse. I just switched out my power supply unit and now my keyboard and mouse is not working. It is a model 3000 and has a white usb receiver
I am transitioning from a Microsoft ISA server to a Cisco ASA 5510. So far so good, until it comes to getting AAA functioning properly. I have a Microsoft IAS server that is functioning properly, however when I try to test it through the ASA's ASDM it errors out. When I run a packet trace it shows it's being blocked by the dreaded implicit ACL. The funny thing is that I can ping and traceroute to the IAS server from the ASA. I found numerous config examples for AAA using IAS, but still not working.
Could it possibly be behaving this way because my ASA and my IAS server are on two different internal netowrks? (172.31.1.x-ASA, 10.1.1.x-IAS)
In my organization we are having 12, LMS 3.2 servers deployed across the globe. As per Audit policy we need to deploy Microsoft win2003 server security patches on all servers using WSUS. Every month our server team sends us query before applying the patches regarding it's compatibility with LMS.
In another thread here on HardOCP, webdev511 made the first mention I've seen of Microsoft's new malware cleaner. MS is making clear that Microsoft Security Essentials (MSE) is for prevention, while Microsoft Standalone System Sweeper (MSSS) is for removing existing infections of difficult-to-remove malware.The obvious competitors to MSSS are ComboFix and Malwarebytes' Anti-Malware. Having been lucky enough to not suffer an MBR-based malware, I'd like to hear what is best to do should I run into one.
We just set up the AnyConnect SSL vpn on our ASA. I am able to establish a connection fine using the Cisco AnyConnect client. I would like to use the native Windows VPN client though if possible. What configuration changes on either the firewall or the client I would need to make for this to happen?
how to use Microsoft server 2008R2 NPS with cisco wlc 4400.am i correct, each LWAPP AP have to be connected to NPS . (this AP is also called access server)?when client tries to connect to the wlan, (in this case lets say we want a user in AD, after providing its creds, can access the network, internet etc) the auth req is sent from AP to NPS/RADIUS? where does WLC come into play here, what does WLC do?
Are there any configuration documents that shows how to configure a Cisco ASA5540 for client VPN access using smartcards and Microsoft IAS. Microsoft IAS will stand between the ASA5540 and Active Directory.
i need a documentation or a procedure to how make integration LMS 3.2 with microsoft active directory to make usernames of devices appear in end hosts reports.
I have some users from another company who are visiting my company. The use outlook to access their mail. I think it is via RPC over https (ssl). When there are on my network they are unable to send messages but when the connect to an ISP directly they are able to send. I have a cisco 2821 as my internet router and an ASA5505 (8.0.5...i downgraded it from 8.2.3) as my firewall. I have not blocked anything from going out. Of note is that when other users use window live configured for gmail....which uses tls they are unable to send emails with atachements. Regular emails go though no problem. Hotmail can send atachments without a problem (there is no encrytion there). I have narrowed the issue down to how the firewall treats esmtp or tls traffic passing though it. I have already diabled inspect esmtp on the firewall.
On one of our laptops we are using MSN.com as our Homepage. Today when we try to open MSN.com we are directed to a screen wanting us to open a Microsoft account What do you think we can do to eliminate this problem.
My ISP is Cox communications in Tucson, AZ.I was subscribed to their basic ("essential") internet speed tier and was getting about 3.68mbs DL and .78mbs UL.I recently upgraded my service to their "prefered" speed tier which is supposed to be up to 18mbs DL speed. I am now getting about 2.85mbs DL and 4.88mbs UL. I have had two techs out who have completely replaced the drop from the outside pole across the street, installed brand new coax all the way to the modem. The modem is brand new (cisco eMTA) Yesterday, after spending 3 hours trying to resolve the issue, the tech connected his own lap top to my modem and was recieving around 25mbs download. It seems the problem must lie in my computer somewhere, but they weren't even sure what it might be.
Tech Support Guy System Info Utility version 1.0.0.1 OS Version: Microsoft� Windows Vista� Home Premium , Service Pack 2, 32 bit Processor: AMD Athlon(tm) 64 Processor 4000+, x64 Family 15 Model 95 Stepping 3 Processor Count: 1 RAM: 1918 Mb Graphics Card: NVIDIA GeForce 6100 nForce 405, 128 Mb Hard Drives: C: Total - 227553 MB, Free - 155007 MB; D: Total - 10919 MB, Free - 4617 MB; Motherboard: Gateway, MCP61SM2MA, FAB1.0, WYSV80903004 Antivirus: AVG Anti-Virus Free Edition 2011, Updated and Enabled
