i have a brand new (LH118501) 8ch and i cannot access the main menu because it keeps asking for the unit id and user and password.I would like to know if there is a way to reset the unit to factory default so i can access the main menu. If not is there a way to bypass this so i can get into the main menu?
View 8 RepliesOriginally Posted by catsavi have a brand new (LH118501 ) 8ch and i cannot access the main menu because it keeps asking for the unit id and user and password. I don't remember adding one but it is possible i did.I would like to know if there is a way to reset the unit to factory default so i can access the main menu. If not is there a way to bypass this so i can get into the main menu?
View 1 Replies View RelatedI have a Lorex Edge 4 channel surveillance DVR system.One camera shows color, the other 3 show color, but every once in a while one of the others shows color.Have rebooted DVR.
View 1 Replies View RelatedI have a Rover system DVR 4CH with 4 CCTV camera's connected to it i want to view it through a computer stream it on the internet for free i dont want to use DYN web hosting because it cost money.
View 1 Replies View RelatedThe setup looks like this:I have a core swith (HP Procurve) which is connected to Cisco router ( which is ISP router).I have to create vlans and do intervlan between them and reach the ISP router.I created two vlans on HP Core Switch ( apart from default vlan 1) , vlan 99 ip add 10.110.234.1 subnet 255.255.255.128 and vlan 999 ip add 10.110.234.129 subnet 255.255.255.128,vlan 1 ip add 10.110.232.42 subnet 255.255.254.0.tagged the ports of vlan 99 and vlan 999 in vlan 1. I am able to do intervlan routing, but i cannot reach router which is 10.110.232.1 subnet 255.255.252.0.I tried these scenrio on packet tracer, it is working fine.
View 3 Replies View RelatedI was about to portforward to be able to make an minecraft server. but i can't connect to the default gateway 192.168.1.1 so for the moment i use hamachi but i would wannt to portforward it to make it easier for others to join.
View 3 Replies View RelatedThis router is resetting to default(erase router name and passwords and resetting router login to default. only thing i see is my sons has a iphone that will use the wifi and i have set parental restriction on it during certian hours. This past 3 time it has reset in 2 weeks his phone with the parental restricions are common. one other thing is i use the app on my droid to check settings on the router .
so th ecommon points here are one one using wifi threw router and has restrictions on it and outer is me with the linksys app to log into my rrouter and make a change like yuring on parental controls on..
but what happens is the router will reboot and renames itself to cisc05179 and cleared all protection and sets router to unsecured.
I have a used 1252 wireless AP. I can't get into it. How do I reset to factory default?
View 1 Replies View RelatedI have 2 WRVS4400N routers that were installed at 2 remote locations to provide VPN access to these sites. The routers have been found reset to the factory defaults on three occasions, twice on one of them and once on the other. Both sites are unmanned so no-one is on site to have pressed the reset button, and both routers were set to have remote management disabled. They are running v2013 firmware.
View 3 Replies View RelatedI have a WRT54G router Ver. 5 with firmware v. 1.02.5. This is the second time this has happened to me but the router reset itself to the factory defaults. I lost all my configurations. I'm saving the configuration this time but it will be annoying to keep having to reconfigure the router.
View 9 Replies View RelatedLast year our Network Security Supervisor submit his resignation and unfortunately did not endorse us the admin password we already tried the password he suggested when we contacted him but nothing of them works. Is there anyway we can reset the password without resetting to factory default?
View 1 Replies View RelatedI have been using my ACER tablet with my Netgear router for several months with no problems at all. Then last night I decided to restore my tablet to its default settings, meaning that all my programs, apps, files, etc., were erased. Then I rebooted my tablet and started from scratch, entering the requested information. Everything appeared to be going just fine until I turned on Wi-Fi and attempted to connect to my network (Secured with WPA2), which was available and showed Good signal strength. I clicked on it, then attempted to enter my password. As soon as I entered the first digit of my password, the option to Connect to the Internet immediately disappeared, becoming greyed-out. Repeated attempts to connect failed for the same reason.
I called ACER Level 2 Support and tried a couple of procedures which didn't solve the problem. One was pushing the Reset Button twice. The technician told me that I may have a problem with my router settings. He suggested that I go to a local fast food outlet and see if I could connect there. I went to McDonald's and was able to get on the Net without using a password. I returned home and tried again to connect, but still was unable to enter my password.
Would it make sense for me to completely disconnect my router from everything, then reconnect and go through that set-up process all over again? I guess I would have to change my User Name & Password, or whatever is required. Also, if I go this route, should I change my security setting from WPA2 to a different option -- WEP, for example? I just don't want to foul things up to the point where my laptop wouldn't work. I doubt that would happen. I recently received the Ice Cream Sandwich upgrade which has been working satisfactorily; however, it does mean that I'm now attempting to start over from scratch with a different operating system.
I forwarded port 80. I installed all of the required software, everything. The video feed on the Lorex dvr plays to the monitor. I have followed all of the directions and when I try to connect remotely I am missing a plug-in or add-on depending on if I use Firefox or IE.it is the Lorex 110 model I am using windows 7.
View 4 Replies View RelatedI forwarded port 80. I installed all of the required software, everything. The video feed on the Lorex dvr plays to the monitor. I have followed all of the directions and when I try to connect remotely I am missing a plug-in or add-on depending on if I use Firefox or IE.it is the Lorex 110 model I am using windows 7.
View 7 Replies View RelatedWhat is the procedure to reset a 1941 router to factory defaults? I just recieved my1 1941 router. I connected it up to my Mac using USB. I got loged in using the cisco/cisco login and it said it will only work once and that I should create a new account. So I entered the command as directed on the screen and it gave my an error about the command. I verified it three times and each time it rejected. While I was looking online for an answer the connection timed out and now I can't get back in.
View 1 Replies View RelatedWe have QoS configured throughout the company, but the standard config we have applied across the 3750 switches only includes the below: We have IP phones (not cisco) attached that are marking with EF, and the PC is an untrusted end device (so needs to be by default marked as zero).Is the above enough to trust VOIP DSCP EF without resetting it to DSCP 0, or do I also need to add a trust line (i.e.: mls qos trust dscp)?
View 2 Replies View Relatedwhy the WAN protocols like Frame-relay, HDLC and PPP are called Layer2 protocols?What is the address scheme they use?
View 5 Replies View RelatedI have got a PC at work (Windows XP Pro SP3) that is on two networks with the IPs 10.20.30.167, subnet 255.255.255.0 (internet enabled) and 10.0.0.20, subnet 255.255.255.0 (no internet). On the 10.0.0.X network there is a gateway with the IP 10.0.0.200 allowing access to another network; 192.168.60.X, subnet 255.255.255.0 (no internet). I have added the route on my work PC to access the 192.168.60.X network via this gateway and I can access all PCs on all three networks from this PC.Now, I am using LogMeIn Hamachi so that I can access the networks at work from home. The PC at work is the 'gateway' PC on the Hamachi network. When installing Hamachi it created a new network connection and bridged this connection with my 10.20.30.167 network adapter to allow access to the 10.20.30.X network from an external PC when connected using the Hamachi VPN connection. I have manually configured my Hamachi connection on my PC at home to the IP 10.20.30.169, subnet 255.255.255.0, with the default gateway set to 10.20.30.167. I can ping all computers on the 10.20.30.X network from my PC at home.
I then added a route on my PC at home for 10.0.0.X to go via 10.20.30.167 (the 'gateway' on the Hamachi network). I also enabled IP forwarding on the 'gateway' PC (my PC at work). I can not ping any PC on the 10.0.0.X network from my PC at home apart from 10.0.0.20 (the other NIC in the Hamachi gateway PC) and 10.0.0.30 (another PC on the 10.20.30.X network that is also on the 10.0.0.X network).Now, with IP forwarding enabled on the Hamachi gateway PC I would assume after adding the route on my PC at home for 10.0.0.X traffic to go via 10.20.30.167 that I would be able to ping all PCs on the 10.0.0.X network...I also tried adding a route on my home PC to send all traffic for the 192.168.60.X network via 10.20.30.167 which has a route via 10.0.0.200 to the 192.168.60.X network, but this also did not work.I then tried adding the 10.0.0.20 network adapter into the network bridge that the Hamachi connection made, also keeping both IPs (10.20.30.167 and 10.0.0.20) on this network bridge by adding them into the 'IP Settings' in the 'Advanced TCI/IP Settings'. I also added the 10.0.0.200 gateway for good measure. I still cannot ping any PC on the 10.0.0.X or 192.168.60.X networks from my PC at home.
I have also added the route to the 10.20.30.X network on a PC on the 10.0.0.X network to go via 10.0.0.20 and tried pinging a PC on the 10.20.30.X network but this also has not worked. Also setting the default gateway on a PC on the 10.0.0.X network to 10.0.0.20 does not allow this...Surely bridging the networks 10.20.30.167 and 10.0.0.20 on my work PC would allow another PC on the 10.0.0.X network to access the 10.20.30.X network after adding the route or setting 10.0.0.20 as the default gateway?
I have two computers. Computer A is connected to the internet through GSM network. Computer A also have NIC adapter which is connected to local network with IP 192.168.33.10/24.
Computer B in connected to internet with DSL connection.
On both machines I use TeamViewer to make VPN secure tunnel between this two computers. Computer A gets IP:7.200.100.2 Computer B gets IP:7.200.100.3
How can I access from computer B to specific device with IP 192.168.33.250 which is on local network of computer A?
Is it possible to route traffic from VPN to other local network, or it is some possibility to use port forwarding from VPN connection to specific IP address on the local network to specific port number?
We have a PPPoE DSL link with a dedicated IP providing by a small ISP(ISP A) in Canada. We are having trouble reaching a small group of IPs in the US to be able to access some client resources.We have eliminated all possible local issues by removing the firewall and making a direct connection to the ISP. We have also had numerous tests prove successful when we use other local ISPs.
Trace routes show that the packets get dropped a few hops from the destination on a US ISP(ISP B).The routes even appear to be very similar to the other ISPs we tested. We escalated to ISP A and they say that everything is working properly on their end and the problem is with ISP B. They claim they "have no partnership with ISP B and therefore cannot create a ticket to get it resolved". I tried calling ISP B but I get nowhere because I am not a customer of theirs.
My solution is to give ISP A the boot, but management has denied that request because of the amount of effort required to switch over. How I can escalate this? Is there anyway to go over and above the ISPs?
I have an skill exercise with 4 Routing Protocols Default Route,Static Route,Eigrp, Ospf. I have about 6-7 routers, and each of them has an routing protocol. But the problem is the Main router INTERNET, which it has to use Static in a direction, and default in the opposite path. This is the scheme of routers and how the r.protocol have to be configured.
View 19 Replies View RelatedThe websites I usually go on now have some type of error page when I go to them. So far it has happened to 2 of them though they might not be related.
Here's what the page says:
Site 1- Valenth
Quote:
Warning: mysql_connect() [ function.mysql-connect]: [2002] Connection timed out (trying to connect via tcp://ec2-184-73-84-14.compute-1.amazonaws.com:3306) in /var/www/valenth.com/include/database.class.php on line 25
[Code]....
i've had this internet problem that has been going on with a wireless laptop i've had since april. it only happens on this computer, and i've tried many solutions. occasionally, i will try and go to pages on google chrome and an error pops up that says "this webpage is not available." when i play games that are online, they get disconnected as well. i've added google chrome and my other browsers to the firewall list and i've also changed the DNS server. when i use the troubleshooter it says something like "router, or modem is not connected to the internet. i've even downloaded the "fix it" program and it detected no problems
View 1 Replies View RelatedI can't get RDP to work on a specific computer.I've already set it up on the router, know the IP address, and I can get it to work great with the server, but the workstation we want it to go to won't accept it.I checked, it's set to allow RDP, the firewall exception was setup, also turned off the firewall completely, removed the antivirus software, checked TCP/IP filtering on the lan connection, even changed the listening port and still nothing.
View 9 Replies View RelatedProblem with a conflicting IP address. Basically on a normal running day my wireless is switched on and connected perfect to my internet, however if i want to download any large files i plug my Ethernet to my laptop and disable the wireless from my laptop, instantly then the LAN connection kicks in and im on the internet again as i find download speeds are faster through a LAN. However today my wireless is fine but the second i switch to LAN the ! symbol appears and a message says their is an IP conflict.
View 2 Replies View RelatedI've been timing out via any FTP client, including FileZilla, FireFTP, and a few others. I even downloaded a few just to see if I could connect with other clients.I contacted my host who can't recreate the issue on their end. I contacted my ISP who instructed me to use my command prompt in order to connect to their server, and that of mozilla. Both times I was able to connect via the command prompt.I don't understand what's going on.If I can connect to the sample sites that my ISP gave me, why can't I connect using an FTP client any longer. What possible change could have been made to have caused that disconnection that happened a few nights ago, and is now causing the timeouts I continue to receive?
View 6 Replies View RelatedHow can i actually change my ip...tryed those cmd things but nothing works. Ineed to change ip somehow.
View 1 Replies View RelatedWe know that every node in the network uses its routing table to forward the packets towards their destination. I have a doubt that which data structure used to implement these routing protocols.
View 6 Replies View Relatedencapsulation of routing protocols. Where exactly in the OSI, or TCP/IP for that matter, model does the data of the routing protocol fit into ? Is it encapsulated inside the transport layer segment payload ? So far from the I've gathered, that's where it should fit.
#####@@@@$$$$routing/procotocol/and/data/etc#####
#-Data link header and trailer
@-Network layer header
$-Transport layer header.
I just received a blu ray player for Xmas that has an Ethernet connection for streaming Netflix,YouTube, etc. my problem is my router is upstairs and the blu ray is downstairs. I really don't want to run an Ethernet cable from the blu ray to the router. Can I use another router on the same network and have it close to the blu ray?,I have a netgear router just laying around and the main router is a Verizon fios router.
View 4 Replies View RelatedI live outside the US but want to listen to US radio stations online and, naturally, a lot of them are blocked because I'm not in the US. I've tried a few places and applications, like UltraSurf, FoxyProxy, to get around this but they either don't work or are so convoluted as to be impossible to use. What else is out there that actually works and isn't pain to use?
View 1 Replies View RelatedI have a need to use two routers (Each with different ISP) on my (LAN) office network.I presently DO NOT want to go the (Two ISP's on one router, or Load Balancing router). I Just simply want two routers with two separate ISP's.I will assign the managers workstations to the faster ISP, and other Workstation to the slower connection.And it seems to work, and all resources seem to be available on the LAN, regardless of which (Gateway) Router(1 or 2) I point the workstation to.I assume because all devices are on the same LAN 192.168.0.XXX Is this a proper way to allocate and use two routers on the same LAN?
View 2 Replies View RelatedHow to get the packet format of CFM used in the provider backbone domain having ethertype (0x88e7) & Itag fields in it. I think wireshark doesnt have this code implemented yet.
View 1 Replies View Related