I have a Lorex Edge 4 channel surveillance DVR system.One camera shows color, the other 3 show color, but every once in a while one of the others shows color.Have rebooted DVR.
View 1 RepliesOriginally Posted by catsavi have a brand new (LH118501 ) 8ch and i cannot access the main menu because it keeps asking for the unit id and user and password. I don't remember adding one but it is possible i did.I would like to know if there is a way to reset the unit to factory default so i can access the main menu. If not is there a way to bypass this so i can get into the main menu?
View 1 Replies View RelatedI forwarded port 80. I installed all of the required software, everything. The video feed on the Lorex dvr plays to the monitor. I have followed all of the directions and when I try to connect remotely I am missing a plug-in or add-on depending on if I use Firefox or IE.it is the Lorex 110 model I am using windows 7.
View 4 Replies View Relatedi have a brand new (LH118501) 8ch and i cannot access the main menu because it keeps asking for the unit id and user and password.I would like to know if there is a way to reset the unit to factory default so i can access the main menu. If not is there a way to bypass this so i can get into the main menu?
View 8 Replies View RelatedI forwarded port 80. I installed all of the required software, everything. The video feed on the Lorex dvr plays to the monitor. I have followed all of the directions and when I try to connect remotely I am missing a plug-in or add-on depending on if I use Firefox or IE.it is the Lorex 110 model I am using windows 7.
View 7 Replies View RelatedFor an assignment in a class I am taking I created a simple network using GNS3 and set up static routing. Everything works fine, I can ping all of the hosts. One of the questions I am supposed to fill out is what happens when I use the "show ip route" and "show ip protocols" commands. When I use "show ip route" I get what seems to be the correct output. However when I use the "show ip protocols" command nothing happens. No output, no error, no nothing. It just goes right back to the prompt. This happens exactly the same on both routers in my network. incase it matters the router is c3640.
PS. would the output be non-existent because I have not set up any ip protocols. In a similar assignment I set up rip and when I used "show ip protocols" i did get what appeared to be the correct output. However I didn't write it down and when I put in the command again about an hour later after I took a break I also did not get an output until I re-entered the rip related commands.
i have this problem when using Remote Live Viewer the Web Remote Client of DviewCam 3.2: i can only see one camera at a time, even more i have to stop playing the current one if i want to change the camera. the viewer shows me the grid for playing many cameras but i don't know if they can be played simultaneously. I can select any camera and will play so i don't think it's an access problem.
View 2 Replies View RelatedDoes the color strips on C3750X stack power cables mean anything, I mean the green and yellow ones. On all Cisco pictures the green one seems to be plugged in the upper ports. I asked local Cisco representative, but he seems not to be sure. We tried to try different scenarios, and it looks like it does not matter what cable end we use. We do not have any external power supply, only interconnecting C3750Xs.
View 1 Replies View Relatedwhen connecting my router to my tv are the wire colors thru or crossed
View 2 Replies View RelatedHow to successfully implement OER w/ NAT? I will have an 1841 with the 4-port EtherSwitch module that will have 3 cable modems connected and utilizing cisco's OER to utilize all 3 links for outbound Internet traffic. However, I am concerned about NAT. The only other interface used on the 1841 will be the connection to the local LAN (inside). I'm thinking this will require a loopback, but I'm not finding anything on CCO to back me up. Is it possible to just let the CMs do NAT? 1 CM is a static IP and the 2 others are DHCP.
View 2 Replies View Relatedi have a problem with a cisco cat. 4507 edge switch as when i have a login ssh session to the switch the supervisor engine restart and the redundant Sup. engine becomes the active and so on this problem mainly happen when i have multible SSH session to the switch and it happened very rarely with a single ssh login
the ios version i use is cat4500-entservicesk9-mz.122-54.SG which im using on all my edge switch and they are all working fine excpt this one
Today I'm going to be re-organzing my network, kind of and I just wanted to get a second opinon. Right now I have an ASA 5510 and a Cisco 2911 and a Cisco 2960 (and I have two more 2911s and 2960s that handles our phone network).
Router 2911 is on the edge Gi0/0 has the public IP and Gi0/1 is not used and then I have 5 individual VLANs (Gi0/1.100, 1.200, 1.300, 1.400, 1.500) VLAN 100 is our internal network 10.10.18.1/24 (router is 10.10.18.1)And the 2960 is used for swichport access, the ASA is on the side and only used as a VPN.
What I want to do is put the ASA on the edge so I can dump all the access-lists and everything then 2911 will only be used to route the traffic. Now I know I will have to reconfigure the VPN, which isn't a problem. My question is when putting the ASA on the edge do I just put the public IP on the ASA's e0/0 and then plug the 2911 into the e0/1 of the ASA and give the Gi0/0 of the 2911 the ip address of 10.10.18.1 or do I just shut it down? The reason behind this is because I would actually like to use the ASA for more than just the VPN passthrough.
I have a very basic networking question If I have, say, 3750's (or any L3 switch, capable of routing) at the edge and a 4500 at the core, where should I route? At the edge? At the Core? Both?
View 4 Replies View RelatedRef a setup required for approximately 300 Surveillance Cameras connected within a LAN. Around 250 Gigabit Optical Media Converters will bring in these cameras to Control Room. Cisco hardware to accomodate 300 IP cameras running on around 12Mbps which makes around 3.7Gbps total on 250 ports. The cameras then have to be distributed to network video recorders and several computers for recording and live monitoring. system that is capable of accomodating around fity more cameras in future.
View 1 Replies View RelatedI am trying to upgrade my 2960 edge switch through tftpd...i have configured vlan 1 with IP address 172.16.10.1 and tftpd as 172.16.10.2 I am trying to ping tftpd, but I couldn't, but when I try to ping vlan 1 from tftpd, i can?
View 6 Replies View RelatedI want to configure Cisco 3560 SWITCH with IP cameras. I need to configure the ports connected to Camers. IP addresses to the Cameras has been assigned.
View 1 Replies View Relatedi have 2 no of 3560G in our core, now my requirement is to establish the redunent network like for the edge 2960G using stack or some other way ...
View 6 Replies View RelatedI need to make some changes on our network. We currently have two sites 150 miles apart we join both by way of fiber and on each side we have Cisco 3750 stack switches, configure trunking for all V lans on one port in site one then through the the long haul fiber to site two with site one using 10.1.1.30 and site two using 10.1.1.40 as their default gateway, with static routing all V lan sub nets to the other sites default gateway life is good.
My question - seeing how we have sites using the same sub net 10.1.1.x to trunk all data to each site through switches; we need to now change the network and add each site to the MPLS network, site one switch 1 IP address 10.1.1.30 going to MPLS router one with FA0/0/0 using IP 10.1.1.31, site two having switch 1 IP address 10.1.1.40 going to MPLS router one with FA0/0/0 using 10.1.1.41. I need to know will this work.
We have the same sub net in each site 10.1.1.x to the MPLS routers then the external router interface connecting each site to local switches, will this cause any problems by using the same local sub net for each site?
I've been fighting what seems to be an increased number of outqueue drops on our core stack and edge switches for the last 3 or 4 weeks.(The core consists of a stack of 5 3750s in 32-gig stack mode. The wkgrp switches are 3560s. all are at 12.2.52) The wkgrp switches are directly connected to users. We use Nortel IP phones with the phone inline with the user PC. auto-neg to 100/full. [code] However I have tried turning off QOS on a couple of workgroup switches (no mls qos, but left individual port configurations the same) but am still seeing drops.Since I have disabled qos on the switches in question (no mls qos) (not the core tho) I am presuming these commands have no affect on the switch operation and therefore cannot be related to the problem. With QOS turned off one would presume that it is general congestion - especially at the user edge where busy PC issues might contribute. So I wanted to see if I could see any instances of packets in the output queues building up.
I wrote some scripts and macros that essentially did a snapshot of 'show int' every 20 seconds or so, and looked for instances of 'Queue: x/' where x was greater than zero.What I found after several days of watching the core stack, and a few of the workgroup switches that are most often displaying the behavior, was that I NEVER saw ANY packets in output queues. I often saw packets in Input queues for VLAN1, once in a great while I would see packets on input queues for fa or Gi interfaces, but NEVER on output queues. [ code] Additionally, when I look (via snmp) at interface utilization on interfaces showing queue drops (both core and wkgroup), they are occurring at ridiculously low utilization levels (as low as 4 to 8%). I've tried to look for microbursts between the core and a wkgroup switch where the core interface was experiencing drops, but haven't seen any (using observer suite). [code] While the queue-drop counts aren't critically high at this point, they are happening more frequently than in the past and I would like to understand what is going on... In most cases, no error counters are incrementing for these interfaces. Is there some mechanism besides congestion that could cause output queue drops?
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies View Relatedwhy the WAN protocols like Frame-relay, HDLC and PPP are called Layer2 protocols?What is the address scheme they use?
View 5 Replies View RelatedI have got a PC at work (Windows XP Pro SP3) that is on two networks with the IPs 10.20.30.167, subnet 255.255.255.0 (internet enabled) and 10.0.0.20, subnet 255.255.255.0 (no internet). On the 10.0.0.X network there is a gateway with the IP 10.0.0.200 allowing access to another network; 192.168.60.X, subnet 255.255.255.0 (no internet). I have added the route on my work PC to access the 192.168.60.X network via this gateway and I can access all PCs on all three networks from this PC.Now, I am using LogMeIn Hamachi so that I can access the networks at work from home. The PC at work is the 'gateway' PC on the Hamachi network. When installing Hamachi it created a new network connection and bridged this connection with my 10.20.30.167 network adapter to allow access to the 10.20.30.X network from an external PC when connected using the Hamachi VPN connection. I have manually configured my Hamachi connection on my PC at home to the IP 10.20.30.169, subnet 255.255.255.0, with the default gateway set to 10.20.30.167. I can ping all computers on the 10.20.30.X network from my PC at home.
I then added a route on my PC at home for 10.0.0.X to go via 10.20.30.167 (the 'gateway' on the Hamachi network). I also enabled IP forwarding on the 'gateway' PC (my PC at work). I can not ping any PC on the 10.0.0.X network from my PC at home apart from 10.0.0.20 (the other NIC in the Hamachi gateway PC) and 10.0.0.30 (another PC on the 10.20.30.X network that is also on the 10.0.0.X network).Now, with IP forwarding enabled on the Hamachi gateway PC I would assume after adding the route on my PC at home for 10.0.0.X traffic to go via 10.20.30.167 that I would be able to ping all PCs on the 10.0.0.X network...I also tried adding a route on my home PC to send all traffic for the 192.168.60.X network via 10.20.30.167 which has a route via 10.0.0.200 to the 192.168.60.X network, but this also did not work.I then tried adding the 10.0.0.20 network adapter into the network bridge that the Hamachi connection made, also keeping both IPs (10.20.30.167 and 10.0.0.20) on this network bridge by adding them into the 'IP Settings' in the 'Advanced TCI/IP Settings'. I also added the 10.0.0.200 gateway for good measure. I still cannot ping any PC on the 10.0.0.X or 192.168.60.X networks from my PC at home.
I have also added the route to the 10.20.30.X network on a PC on the 10.0.0.X network to go via 10.0.0.20 and tried pinging a PC on the 10.20.30.X network but this also has not worked. Also setting the default gateway on a PC on the 10.0.0.X network to 10.0.0.20 does not allow this...Surely bridging the networks 10.20.30.167 and 10.0.0.20 on my work PC would allow another PC on the 10.0.0.X network to access the 10.20.30.X network after adding the route or setting 10.0.0.20 as the default gateway?
my computer is a dell dimension 1100, with a Linksys WMP54G wifi card, running vista home basic.In the wifi thing in the notification area, it shows two wireless networks, One is my normal SSID (Lower Net), and one is "Unidentified network". They are both on one wireless connection (Wireless Network Connection 3). When i try to go on the internet, it says i'm not connected. i tried disconnecting from the unidentified network, but that disconnects me from lower net too.
View 13 Replies View RelatedI have two computers. Computer A is connected to the internet through GSM network. Computer A also have NIC adapter which is connected to local network with IP 192.168.33.10/24.
Computer B in connected to internet with DSL connection.
On both machines I use TeamViewer to make VPN secure tunnel between this two computers. Computer A gets IP:7.200.100.2 Computer B gets IP:7.200.100.3
How can I access from computer B to specific device with IP 192.168.33.250 which is on local network of computer A?
Is it possible to route traffic from VPN to other local network, or it is some possibility to use port forwarding from VPN connection to specific IP address on the local network to specific port number?
We have a PPPoE DSL link with a dedicated IP providing by a small ISP(ISP A) in Canada. We are having trouble reaching a small group of IPs in the US to be able to access some client resources.We have eliminated all possible local issues by removing the firewall and making a direct connection to the ISP. We have also had numerous tests prove successful when we use other local ISPs.
Trace routes show that the packets get dropped a few hops from the destination on a US ISP(ISP B).The routes even appear to be very similar to the other ISPs we tested. We escalated to ISP A and they say that everything is working properly on their end and the problem is with ISP B. They claim they "have no partnership with ISP B and therefore cannot create a ticket to get it resolved". I tried calling ISP B but I get nowhere because I am not a customer of theirs.
My solution is to give ISP A the boot, but management has denied that request because of the amount of effort required to switch over. How I can escalate this? Is there anyway to go over and above the ISPs?
I have an skill exercise with 4 Routing Protocols Default Route,Static Route,Eigrp, Ospf. I have about 6-7 routers, and each of them has an routing protocol. But the problem is the Main router INTERNET, which it has to use Static in a direction, and default in the opposite path. This is the scheme of routers and how the r.protocol have to be configured.
View 19 Replies View RelatedThe websites I usually go on now have some type of error page when I go to them. So far it has happened to 2 of them though they might not be related.
Here's what the page says:
Site 1- Valenth
Quote:
Warning: mysql_connect() [ function.mysql-connect]: [2002] Connection timed out (trying to connect via tcp://ec2-184-73-84-14.compute-1.amazonaws.com:3306) in /var/www/valenth.com/include/database.class.php on line 25
[Code]....
i've had this internet problem that has been going on with a wireless laptop i've had since april. it only happens on this computer, and i've tried many solutions. occasionally, i will try and go to pages on google chrome and an error pops up that says "this webpage is not available." when i play games that are online, they get disconnected as well. i've added google chrome and my other browsers to the firewall list and i've also changed the DNS server. when i use the troubleshooter it says something like "router, or modem is not connected to the internet. i've even downloaded the "fix it" program and it detected no problems
View 1 Replies View RelatedI can't get RDP to work on a specific computer.I've already set it up on the router, know the IP address, and I can get it to work great with the server, but the workstation we want it to go to won't accept it.I checked, it's set to allow RDP, the firewall exception was setup, also turned off the firewall completely, removed the antivirus software, checked TCP/IP filtering on the lan connection, even changed the listening port and still nothing.
View 9 Replies View RelatedProblem with a conflicting IP address. Basically on a normal running day my wireless is switched on and connected perfect to my internet, however if i want to download any large files i plug my Ethernet to my laptop and disable the wireless from my laptop, instantly then the LAN connection kicks in and im on the internet again as i find download speeds are faster through a LAN. However today my wireless is fine but the second i switch to LAN the ! symbol appears and a message says their is an IP conflict.
View 2 Replies View RelatedI've been timing out via any FTP client, including FileZilla, FireFTP, and a few others. I even downloaded a few just to see if I could connect with other clients.I contacted my host who can't recreate the issue on their end. I contacted my ISP who instructed me to use my command prompt in order to connect to their server, and that of mozilla. Both times I was able to connect via the command prompt.I don't understand what's going on.If I can connect to the sample sites that my ISP gave me, why can't I connect using an FTP client any longer. What possible change could have been made to have caused that disconnection that happened a few nights ago, and is now causing the timeouts I continue to receive?
View 6 Replies View RelatedHow can i actually change my ip...tryed those cmd things but nothing works. Ineed to change ip somehow.
View 1 Replies View RelatedWe know that every node in the network uses its routing table to forward the packets towards their destination. I have a doubt that which data structure used to implement these routing protocols.
View 6 Replies View Related