I have a router and a server that are connected through two unmanage switches. The router has DSL service in it and I want to access the internet on the server but I can't. The two are in the same network and it is a static IP network. I can ping the router from the server.
View 36 RepliesI cannot seem to see my server behind a cisco router. I have a feeling it is because our network phone system may be robbing the IP address?We have two fixed IP addresses.The first one, is assigned to the router.We have two swtiches set up behind router and all the other network stuff interanally wrks great.We also have full internet access. When I type the IP in on the web, it accesses the talkswitch phone system.I have set the internal IP to the server as fixed.I have port 21 open for FTP.When I run a test, the internet sees port 21 open. However, I cannot seem to cal lup the server over the internet. Could the talkswitch system somehow be interfereing with the logon?What would the proper syntax be to access the server?
View 3 Replies View RelatedI am having a similar problem to a couple others with the dir-651.Frequent Disconnects difficulty even connecting to routers home page.Internet worked ok on dir-615 i had before, just slow gaming speeds occasionally running vista 64 Timewarner cable.And i do have the newest firmware.
View 3 Replies View RelatedMy problem is I can not connect to any ftp server or any database server using my home internet connection. But i can connect to the same servers using my work internet or even using my 3G mobile connection.I tried to contact with my service providers with no luck.I am using a Zyxel wireless router. Is there any settings in my router which stops me to connect those servers.
View 4 Replies View Relatedif i flash my firmware on my router, can i still view the router logs before the flash? i heard that .logs can be on the ram of the router.
View 1 Replies View RelatedI have a little probs@a site .we have a vsat link connected to a linksys E1000 router which is pluged into a cisco 2950 switch doing DHCP to the LAN,then a WAN link configured on a cisco 2911 router on static ip which is pluged into the same switch to serve the same LAN.I have been having issues of the workstations accessing both the WAN and internet@ the same time.
View 1 Replies View Related active# sh running-config
: Saved
:
ASA Version 8.2(5)
!
hostname active
domain-name dhalahore.org
enable password 2KFQnbNIdI.2KYOU encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code].....
I have the Apple Time Capsule connected to my ISP using PPPoE and it is working just fine creating a wired and wireless network. The IP address of TC is 192.168.1.1 and I have set it's DHCP range between .100 to .200Next, I wanted to add VPN to the router as I live outside the US and wanted to access some services in the US. So I got an ASUS router and flashed it with Tomato firmware.I assigned the ASUS as IP address of 192.168.1.10, connected this it to a LAN port on the Apple and used a DHCP type Internet connection to set it up. I then created a second WiFi Network and gave the DHCP range between .11 to .20Now using any Wi-Fi device, I can connect to either of these networks and browse the web just fine. The ASUS is all setup as a VPN client so any traffic going through the ASUS is through a US based VPN.
View 5 Replies View RelatedI no longer have my netwk admin and i moved the server to my residence and i also have the pcs that logged on.i booted the servers up and connected the pcs using a router but can't log on im using a verizon wireless router can i get rid of that since i dont want to have it on the internet.
View 1 Replies View RelatedI got an internet from provider (which is LAN cable sticking from the wall) - and it works fine when I connect via LAN cable - when I write the IP Address, Subnet Mask, Default Gateway, and DNS servers on the LAN adapter and create a PPPoE connection with username and password. I want to do the same but wirelessly. I have an ASUS RT-N10 LX wi-fi router - and connected the cable from the provider to the WAN slot on the router. Then I have accessed the router from my laptop [URL] - and configured everything as it was on my laptop.
IP Adddress: 192.168.17.191
Submask: 255.255.252.0
Default Gateway: 192.168.16.1
DNS1: 192.168.1.250
DNS1: 192.168.1.10
Wireless network works fine, the default gateway is pinging - but DNS servers are not accessible. As a result no internet connection available ( Moreover - when I want to ping the DNS (ping 192.168.1.250) - I tries to get a response from other location 192.168.1.3
We need internet connectivity on all workstations
View 1 Replies View Relatedi have one machine have 2 Ethernet devices and i need to connect this server to different 2 network with 2 different gateways (192.168.2.x "vpn network" and 192.168.1.x "adsl network" )so if any other one need to connect this ftp server can connected from vpn or adsl
View 1 Replies View Relatedi just want to ask how can i block all proxy server websites in my router( any brand ) so that no one can access, like facebook i already block it in the router but they still access using proxy server website.
View 2 Replies View RelatedI want all the computers on my LAN to access via a proxy server in another country. I have a Netgear DG 834N router and would like that to connect to the proxy server rather than having to define it on each browser.
View 1 Replies View RelatedI'm trying to install ios into my cisco 2821 which boots in rommon. Apparently the ios is corrupted, I have set the IP_ADDRESS, IP_SUBNET_MASK,DEFAULT_ GATEWAY, TFTP_SERVER, TFTP_FILE but anytime I issue the 'tftpdnld' and confirm to continue, the process will time out give this error message" ARP: address resolution for 10.203.8.49 timed out.ARP failed with failure code 1. TFTP transfer aborted.
View 6 Replies View Relatedipconfig /all reports one of my three DNS servers as 192.168.1.1. My Default Gateway and DHCP Server are also reported as 192.168.1.1. This is from a recently installed Valet M10 updating an old Linksys router. The Linksys reported the three DNS servers octets independent of the router's ip and other default settings.JK
View 1 Replies View RelatedThe automatic connection to the preferred network (with a strong signal) does not occur immediately. When I choose it in the list of preferred networks and click on 'connect' (with the password present of course), a message appears stating that the computer is connecting to the network. However, after some time nothing happens and the message terminates. There is no other information given (e.g. 'the computer failed to connect..."). After up to 15 mins or so, the network connects automatically (not sure if this has anything to do with turning the router off and on, restarting the computer, turning the wireless adaptor off and on....)
View 4 Replies View RelatedWe have a quad port NIC on our Dell server.I want to take all 4 ports and plug it into our switch and have it all go to the same IP of the server and just have to share the data load in/out.Do I need to configure anything to do this?
View 6 Replies View Relatedmy laptop is re-staring when access the server
View 1 Replies View RelatedI have a Windows Home Server v.1 I set it up nearly a year ago, and everything runs fine.I have 3 different user accounts that are password protected.On my PC, i have been running Windows 7 and using the server as my My Documents folder.I recently installed Windows 8 Consumer Preview on an old Hard Drive, and i can't seem to access any folder on the server that isn't already given public permission. Whenever i try to access my User folder i get an access denied message, but no prompt to enter a password so i can use it.
View 3 Replies View RelatedI get stuck in a problem,What can be the reason for not working my configuration or any other reason that can be .
[CODE].....
Is this possible and if so what commands do i need to configure on my ASA 5510 for it to work.I have two web server within my DMZ and i want to access the outside url of on on the web server from the other. Currently i can access the internet from both webserver server but not the url form either webservers.
E.g. config
webserver 1 https://xxxxxx.xxxxxxx.com ---> public ip---> dmz ip
webserver 2 https://xxxxxx.xxxxxxx.com ---> public ip---> dmz ip
I have a new SG300-28P, and have had occasional issues with being unable to connect to it via anything other than the serial port. I have connectivity between my machine and the switch (tested with ping each way), and in fact, have the same problem if I take a laptop to the switch and connect them directly.What happens is that though the switch is operating normally, http, https, ssh and telnet attempts to access all fail in one way or another. Ssh and telnet either yields no response or a refused connection (even though those services are enabled). For http and https, I'll occasionally get enough of the web page to be able to tell what it is ... but attempts to log in just don't work.While this is happening, the CPU and packet load on the switch is very, very low.Rebooting didn't work entirely, though it may have made it better. Resetting to factory defaults and then reconfiguring makes it work.This is using the latest firmware: 1.2.7.76.
View 3 Replies View RelatedI recently bought a personal laptop that I'd like to use at work. It came with Windows 7 Home Premium installed and because of that, I can't join it to the Windows Server 2003 domain we have. I don't really need to print or any of the other things that go with being on the domain, I just need access to a few key folders. Is there any way to access shares on the server with Win 7 Home?
View 2 Replies View Relatedi'm getting "general network error" while accessing application from server..
client machine: Windows 7
server machine: Windows 2008 server
Switch : 24 port unmanaged D-Link switch ..
network cable: CAT-5 cable.
I am having some trouble understanding extended control lists. I am trying to prevent a certain host on LAN1 from accessing a server on LAN2, while still allowing the host access to the rest of LAN2.This is what I thought the command should be:
access-list 100 deny ip 175.16.1.2 0.0.0.0 175.17.2.2 0.0.0.0
My understanding was that:
Green = source & mask
Red = destination & mask
However this seems to stop all my other hosts on LAN1 from pinging the server also.
We have a ASA5510 with a webserver in the DMZ network 10.2.2.0/24. We now want this web server to be able to access the Exchange server in the Inside network 10.1.1.0/24. I researched this and it seemed straight forward according the the Cisco document below:
[URL]
I'm looking to do this with smtp so I added these lines to the config:
static (inside,DMZ) 10.2.2.30 10.1.1.11 netmask 255.255.255.255
access-list dmz extended permit tcp host 10.2.2.2 host 10.2.2.30 eq smtp
The configuration line:access-group DMZ in interface DMZ Already existed in the configuration so didn't need to be re-entered.
ASA Version 8.0(4)
!
hostname xxxx
domain-name xxxx.com
enable password xxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxx encrypted
names
[code]....
I have Cisco ASA 8.0(5) and I need to block specific url to acees my https server in dmz ?I read about websence technology, but I think it's not free right? Also I read abotu policy inspection map's but in my case is HTTPS not http ..
View 1 Replies View RelatedI have a VPN connection to my office network. The VPN connection appears to work fine as it connects and logs me in successfully. In the connection box I have to provide a domain and my username to log in. Once the VPN is connected I am then able to ping my office computer as if I was on the same network. That is great. The problem is that there is a server on that network that defines a bunch of A records for web applications we are working on and I can't seem to hit any of those from my home computer, even though I can at work. If I remote into the office PC and navigate to these addresses they work fine. I also know that my co-worker can hit these a records from home so it has to be something I'm doing wrong.
[Code]....
i want to ask if i can link two routers while they are totally separated of each other over the internet to make a large LAN the two routers are TP link?
View 5 Replies View RelatedHow do i connect two internet routers to one IP address range?I currently have one broadband router connected on 172.16.0.3 subnet 255.255.0.0, I have a second line which is a copper ethernet EFM 2Mb line connected using a Cisco 1800 router configured on 172.16.0.254 subnet 255.255.255.0, no DHCP is configured on either router. the dhcp is provided by a windows 2003 server on our LAN which is also configured on the same LAN IP range. if i connect the Cisco router into the same switch as the broadband router my network devices stop working and dont respond.
If i check the broadband router it shows all the connections to it as having the same MAC address as the Cisco router?? if i disconnect the Cisco router everything returns back to normal and works perfectly.What I want to achieve is to be able to run both routers on the same LAN to provide internet access by configuring the pc's to route through a specific router. the DHCP I want to stay routed through my original broadband line. at the same time i want all pc's to access to the lan devices (ie. servers and printers) what the correct configuration would be for the two internet routers would be?
I have a question regarding CSS loadbalancer. Let's say there are 2 vlans in CSS:
1. Vlan 10: 10.1.1.0/24 as external interface, interface where most of the clients are coming from.
2. Vlan 20: 10.1.2.0/24 for real server vlan.
Virtual IP 10.1.1.10 is created in CSS on behalf of two real servers (10.1.2.11 & .12) in Vlan 20. Client from Vlan 10 can http access to 10.1.1.10 successfully.
In Vlan 20 there's also few clients which need to access servers via virtual IP. Vlan 20 Client PC (10.1.2.101) can ping 10.1.1.10, but can't access 10.1.1.10 http service.
Is there any way for CSS to forward service request coming from Server vlan to be send back to the same segment?
We have ASA5520 and we want to configure a VPN IPSEC profile so that a partner of ours can access only a server and only on HTTP port.I've tried configuring split tunneling with an Extended ACL but probably I'm missing something. I just configured the ACL so that it included any source to our server's IP on HTTP port but when testing, it didn't work.
However, if I configure a Standard ACL on the split tunneling I can access the server and all the services it provides.Do you know if I'm missing anything on the Extended ACL configuration?
Should I configure this any other way?